Good information, however, I really have to ask, what situation would you want to convert a G40 from a flat tip, to RAC? Thank you
@MEVD2011
4 жыл бұрын
Great video Darren keep them coming 👍🏻
@AirlessDiscounterInternational
4 жыл бұрын
Thank you so much! :)
@grubbetuchus
2 жыл бұрын
What about going from a RAC tip, converting back to a flat tip? What are the part numbers? Converting from a G40 262929 to a G40 262932?
@MEVD2011
4 жыл бұрын
Someone put a thumbs down 😂 you couldn’t make it up could you maybe he don’t like clear and informative videos 😂😂😂😂 #lemon 😂😂
@seasgarage
2 жыл бұрын
Sebastian vettel's brother paints? Great video.
@wesleyburke7514
3 жыл бұрын
Informative... thanks
@joobasics6891
24 күн бұрын
How does it compare with a Kremlin set in terms of quality of finish?
@AirlessDiscounterInternational
24 күн бұрын
We have too little knowledge about the brand Kremlin since we don't work with, to say which one is better. But in terms of professionnal quality finish, we can say that the G40 and now days the G50 stand by the top air-assisted guns on the market for contractors and industries! - G50 : airless-discounter.de/Graco-PerformAA-50-Air-Assisted-Spray-Gun-with-General-Finishing-Air-Cap-AXM311-Nozzle-26B510 Kind regards, Airless Discounter team
@Igor-q3f
Ай бұрын
Is there any other accessories for this gun? My graco rep showed some kind of needle to make closer to the hvlp.
@AirlessDiscounterInternational
Ай бұрын
Hi, Thank you for your enquiry. We don't have an extension or any other accessory for this Graco Aircoat gun, but you'll find filters (#60, #100 and #200) as well as nozzles and the air cap in our shop. - Nozzles : airless-discounter.de/Spray-Tip-for-Graco-G15-G40-Spray-Guns-AirCoat - Filters : airless-discounter.de/spray-gun-filters - Air cap : airless-discounter.de/Graco-AIR-CAPASSY-249180 And all the spare parts needed to repair it of course. Kind regards, Airless Discounter team
@liquidprogressions
2 жыл бұрын
Can you put the tip on the FastFinish Pressure Boosted Hopper Gun
@AirlessDiscounter
2 жыл бұрын
No
@benjoyce727
Жыл бұрын
l am spraying 150 -200mm timber using an oil based enamel with the G40 which tip would l use
@paulricketts2863
3 ай бұрын
208- 315 depends on the width
@Artie6937
4 жыл бұрын
Hi I have the Wagner 4600 i normally use flat tip, however I have tried the reverse tip conversion and you can squash the fan but spitting occurs, does the graco spit with this conversion ? Cheers
@AirlessDiscounterInternational
4 жыл бұрын
Hi Artie, it will be difficult to make an assessment of the spitting occuring on your Wagner 4600 without inspecting the spray gun directly. We haven't had any customers report an issue with Graco G40 with the conversion kit so far.
@duartepaintinghandymanservices
4 жыл бұрын
Perhaps your gun needs new packings
@Artie6937
4 жыл бұрын
The Wagner spit with the reverse tips because air horns are designed to adjust the fan pattern size only but there none to further atomise the paint like the flat tip air cap
@duartepaintinghandymanservices
4 жыл бұрын
Artie6937 have you tried to increase the pump pressure, the reversible tip can be atomized with only the pump pressure, maybe you have the pump to low and the air as well causing to spit, raise the pump pressure and play with the air pressure after. I would start with around 2 pounds of air, the wagner also has a fan adjuster I believe
@Adamulduren
4 жыл бұрын
Is there difference between spray quality between two of them
@AirlessDiscounterInternational
3 жыл бұрын
Hi, Thanks for your comment. From our experience, if you compare the G40 with classic aircoat tip and with reversable tip ; the classic one will always remain the best in terms of finish and precision. Kind regards, Airless Discounter team
@eleelife
3 жыл бұрын
What kind of a compressor do you need to run this gun. I have a titan 440 and a 5 cfm at 90 psi 1.5 hp compressor, would that be sufficient?
@AirlessDiscounterInternational
3 жыл бұрын
Hi, A small compressor will be sufficient, as only the gun needs to receive it and in AirCoat it is gonna be never more than 2 bars of air pressure needed. Kind regards, Airless Discounter team
@rattlinbucks
10 ай бұрын
Did you ever try running this gun with your 440 and compressor?
@coryblair5503
3 жыл бұрын
What one is better?
@AirlessDiscounterInternational
3 жыл бұрын
Hi, It is always preferable to stay with flat nozzles in Air-assisted spraying but both work. Kind regards, Airless Discounter team
@Painter95
2 жыл бұрын
where can i get the conversion kit from flat tip to racx tip?
@AirlessDiscounterInternational
2 жыл бұрын
Hi, If you have the following G40 models, 262932 & 262929 ; you can use this ref : 24U616 - www.airless-discounter.de/Kit-de-conversion-Graco-buse-plate-vers-buse-RAC-24U616 If you have these ones, 24C855 & 24C856 ; you can use this ref : 24C791 - www.airless-discounter.de/Kit-de-conversion-RAC-de-pistolet-Graco Kind regards, Airless Discounter team
@Skabanis
4 жыл бұрын
I have the 595 sucks cleaning those 100 dollar tips
@AirlessDiscounterInternational
3 жыл бұрын
Hi, it can take some time but we are also offering these needles if you want to try : www.airless-discounter.de/Tip-Cleaning-Needles-Needles-for-Spray-Tips Kind regards, Airless Discounter team
Пікірлер: 31