Put a pump on that 50 gal. barrel and pump it into a dumpster or an enclosed dump trailer. My son has this exact planer, and yes it creates lots of sawdust. He has a large Oniada dust collector for his shop, but only a 30 gal trash can for collecting the dust. When the dust collector is turned on the pump comes on also. They never have to manually empty the trash can. It goes directly into a covered dump trailer with high sides.
@portercreek
3 ай бұрын
Yeah, mine fills up really fast too!
@seg32
Жыл бұрын
Ron @ Hawthorne Woodcrafters Our Club has 235 members. We just took delivery of a Grizzly G1033x. We have to upgrade the wiring from 20 amps to 30 amps ( 10 gauge wire ). Our old Grizzly was 20 amps with 12 wire. Would you or have you added an hour meter as a reminder for maintenance? We enjoyed you review.
@portercreek
Жыл бұрын
I have not considered putting an hour meter on it, I don’t think I will. Thank you!
@hentges9182
Жыл бұрын
I have been trying to decide between the Powermatic and grizzly.
@portercreek
Жыл бұрын
Grizzly has my vote!
@ralphturney2125
Ай бұрын
As a woodworker you never thought of using a simple wood wedge to lock the top roller in place???
@portercreek
Ай бұрын
@@ralphturney2125 that is what I do now
@markisom78
Жыл бұрын
I noticed you have your planer plugged into a long extension cord. This might be the reason your machine was bogging down under heavy use. I'm assuming your machine is like my Jet 20 inch planer and needs a 30 amp breaker. Over time that extension cord can get hot with that much amperage running through it. Your better off installing a 220 volt outlet near your machine to plug in. Not only does that greatly reduce the heat generated by big amperage, but it also provides a better ground which will prevent any electrical shorts.
@portercreek
Жыл бұрын
The extension cord is oversized so it is not an issue, thanks for commenting.
@ok-hd4so
5 ай бұрын
thats only an issue if you use thin extension cords.
@CaptMike
Жыл бұрын
I have one of these and it has been nothing but a problem feeding. Yes, I have adjusted it three times and tech support has been no help. I even made a video showing the problem and no answer so far. Any suggestions?
@portercreek
Жыл бұрын
What type of wood are you planing? Is the table cleaned and waxed? What have you adjusted one it? There are a couple different things that you can adjust that will affect how it feeds. Can you send me a link to the video?
@CaptMike
Жыл бұрын
@@portercreek Mixed, Oak, Pine, Walnut, etc. Yes to all the above, but ome thing you did suggest cleared up some of the problem. I adjusted the bottom roller all the way up and it helped a lot. I still have a problem with something hanging up as the wood exits. I'll keep working on that.
@portercreek
Жыл бұрын
@@CaptMike when I am planing rough sawn boards I put the rollers all the way up and when I am doing final planing I drop them down all the way to get a better finish. Boards feed through a lot better when they have been smoothed out first. If you are still having an issue with feeding you can lower the feed bar a little more. If you go too far then you won’t be able to take shallow passes because the feeder bar will leave dimples. There is a balance, just have to find that sweet spot! Best of luck! Please don’t forget to hit that subscribe button!
@franka5416
Жыл бұрын
If you haven't already, take a look at Scott Barron's video on calibrating the infeed/outfeed rollers and the chip breakers. It's an excellent video: kzitem.info/news/bejne/w6qZtHyun3amg6w Let us know if something from the video makes a difference for you, hope it helps.
@jamesmcgregor9491
6 ай бұрын
Is the outfeed roller serrated steel or rubber?? The steel roller can leave an embossed marked finish that needs sanding, especially on narrow boards. This is a problem I have with my planer. I think the newer G1033X planer was upgraded to a rubber outfeed roller. Would like a comment on this. Thanks. Jim
@portercreek
5 ай бұрын
I believe the outfeed roller is rubber, I will have to verify though.
@hawkeye3367
Жыл бұрын
Nice review. What type of dust collector are you running? Thanks!
@portercreek
Жыл бұрын
I have a big Oneida 5hp cyclone dust collector.
@auvis1
Жыл бұрын
Thanks for making this video. Do you lock your table with the table locks every time you adjust the table height with the handwheel?
@portercreek
Жыл бұрын
I don’t think we’ve ever locked it! Never had any issues!
@jebahbaum1542
6 ай бұрын
wish someone would do a demo for adding oil to the gear box. The maual is useless
Пікірлер: 24