For the SEV (Vertical Electrical Sounding) method, in which resistivity measurements are taken at different depths, how do I define the two layers for the calculation? I am currently working on ETAP 12.6.0
@hrikeshnakhan6588
3 жыл бұрын
how to design the earthmat using bentonite treatment for limiting the Rg value to desired value?
@ETAPsoftware
3 жыл бұрын
Thank you for your interest in ETAP Software, please contact our Technical Support at helpcenter.etap.com/ for more information
@canhochothueBinhDuong
Жыл бұрын
Thank you so much for your sharing, but i have a question that in some case, we design system with special shapes such as the grounding system of the wind turbine (Circle shape) or in case of low resistance need to install additional wells, in which case how to handle it. Looking forward to the answer.
@ETAPsoftware
Жыл бұрын
Thank you for your interest in ETAP Solutions and the Ground Grid Design module. Please contact out Help Center at helpcenter.etap.com or contact one of our ETAP offices at sales@etap.com
@tkjfifkfif995
2 жыл бұрын
Great! Thank you so much !
@ETAPsoftware
2 жыл бұрын
Thank you for your interest in ETAP Solutions and your positive feedback.
@hakantarhan770
2 жыл бұрын
Split factor sample calculations required to understand further
@ETAPsoftware
2 жыл бұрын
Thank you for your interest in ETAP Solutions. Please contact our 24/7 Help Center for assistance helpcenter.etap.com/
@sheriffolanrewaju6111
Жыл бұрын
How can I download etab software or how can I get it
@umutnesil2295
2 жыл бұрын
What happens to step potential and touch potential if system is with NER reducing the ground fault current?
@ETAPsoftware
2 жыл бұрын
Thank you for your interest in ETAP Solutions. Please contact our 24/7 Help Center for assistance with your question: helpcenter.etap.com
@sumitmondal548
3 жыл бұрын
Hi, do not you have hard-drawn copper material for the earth grid? Some client is specific for hard drawn copper.
@ETAPsoftware
3 жыл бұрын
Thank you for your interest in ETAP Software, please contact our Technical Support at helpcenter.etap.com/ for more information
@daravannmel4125
2 жыл бұрын
Thank you so much for your sharing! However, I have some question for some part of the software function. For Soil Editor, Soil Analysis function, mostly you put data from filed test (4 points test/wenner);then, you got result from it. What is the difference between soil resistivity result at site and software? Other points, the result also show the depth of surface layer, how did software solve soil structure without soil investigation (Dig/SPT/etc method)? Thank you for your answer in advance!
@tomandetap3079
2 жыл бұрын
Thank you for your interest in ETAP Products. For detailed product feature information please contact our 24/7 Help Center helpcenter.etap.com for assistance or contact you local ETAP office etap.com/offices
@yichenbi3863
2 жыл бұрын
Hello, the program requires the 2 layers soil model. Therefore it is necessary to convert the field test data into the the required model. The soil analysis helps the conversion. This conversion is similar to the Sunde graphic method as described by IEEE80. It is suggested to contact ETAP support for further questions as this topic is a little bit involved.
@daravannmel4125
2 жыл бұрын
@@yichenbi3863 Thank you for your explanation! However, what is the difference between field data measurement and field data calculated by the software?
@m_malik10
2 жыл бұрын
How can we design earthing using ETAP for the substations with High resistivity and/or high Short circuit Current case?
@tomandetap3079
2 жыл бұрын
Thank for your interest in ETAP Products. Please contact our 24/7 Help Center helpcenter.etap.com for assistance or contact you local ETAP office etap.com/offices
@marcozanotti15
3 жыл бұрын
Hi! I'd like to ask you how to associate the Rg value in order to modify line-ground faults, i mean Isc = Vf/(Z1+Z2+Z0+Rg). Thanks.
@ETAPsoftware
3 жыл бұрын
Thank you for your interest in ETAP software. Please contact ETAP support at support@etap.com, login into our HelpDesk and open a ticket, or contact your local ETAP office or representative
@frataslan2052
2 жыл бұрын
Hi, How can change unit system to metric system in ground grid analysis? i cant find
@ETAPsoftware
2 жыл бұрын
Thank you for your interest in ETAP solutions. You would have to start your project in IEC standard mode and it will automatically use metric units. Please feel free to contact our 24/7 Help Center if you need further assistance: helpcenter.etap.com
@muhammetortagun1465
2 жыл бұрын
Thanks
@ETAPsoftware
2 жыл бұрын
Thank you for your interest in ETAP Solutions and your positive feedback.
@christopherserojano3953
3 жыл бұрын
Hi, for older substation, how should I measure if the ground mat/ grid is still within the acceptable standards?
@ETAPsoftware
3 жыл бұрын
Thank you for your interest in ETAP Software. Your question was forwarded to one of our engineers who will be in touch shortly. In the mean time feel free to contact our 24/7 online Help Center at support@etap.com
@yichenbi3863
3 жыл бұрын
Hello Christopher, generally you can still model the old substation based on its original drawings or you can measure its ground impedance.
@douglasreyescordero7117
2 жыл бұрын
@@yichenbi3863 Hi, Also is very important measure Step and Touch voltage in Old substation and cheack if the value comply with the IEEE 80 what is the most important than Ground impedance. Saludos
@germanmonje3662
4 жыл бұрын
Excelente, sus mejoras en optimizacion y garficas
@ETAPsoftware
3 жыл бұрын
Gracias por su interés en ETAP Software y por sus comentarios positivos
@furkanokn3375
2 жыл бұрын
Could you share the material ? Thanks
@ETAPsoftware
2 жыл бұрын
Thank you for your interest in ETAP solutions. We typically do not share our presenter files. Please feel free to contact our 24/7 Help Center if you need further assistance: helpcenter.etap.com
@vater1665
2 жыл бұрын
nice
@ETAPsoftware
2 жыл бұрын
Thank you for your interest in ETAP Solutions and your positive feedback.
@johngriffin3704
Жыл бұрын
I'm really not trying to be a jerk here but in the interest of giving you some feedback that will improve future presentations, consider using the phrase Ummm a little less. You do it excessively and it makes it difficult to follow your information stream. Otherwise it was a great and thorough presentation!
Пікірлер: 37