Does anyone else of knowledge see when the counter weight base plate is lifted off the trailer it is dangerously close to flipping upside down in the straps?
@lennyc624
6 жыл бұрын
Sny734, it sure looks that way. On the link belt you pick it up from the top. It looks like they could have done that here too.
@alltree78
5 жыл бұрын
Because the chains go up thtough the middle of the counter weight and there are 4 equal points of lift it supposedly lol wont flip
@MFKR696
5 жыл бұрын
@@alltree78 Sounds great on paper, but when you introduce human stupidity into the equation, anything can happen lol. Murphy's Law and all that... Never underestimate the power of complacency.
@Sny734
4 жыл бұрын
@@alltree78 The base plate the base plate. No chains. It was lifted with slings
@dilbagsingh9940
2 жыл бұрын
👍👍
@СергейСидоров-л7ь
6 жыл бұрын
Классно
@ЮркаОдессит
5 жыл бұрын
При чем минус 25 для людей сделано
@stevemacca786
5 жыл бұрын
The equivalent Liebherr looks 100% easier.
@antpurple8292
2 жыл бұрын
Saw the Liebherr crane & everything was done by the crane. This 1 is done by manpower👎🏾
@ganjabassdmx253
5 жыл бұрын
Класс 👍
@mannlynnrelaxationcommunit4894
5 ай бұрын
Gd crane but grovea sensor are not very hd spoil faster than otjer crane maybe vrove R&D sgould look into it
@zhanibek2252
7 жыл бұрын
ми күшті екен
@jimsvideos7201
8 жыл бұрын
This takes how long? Day or so?
@manitowoccranes
8 жыл бұрын
+Jim's videos It takes roughly 2.5 - 3.5 hours depending knowledge/ experience with the equipment
@intellidog58
6 жыл бұрын
Manitowoc Cranes like to see the load chart and boom length configurations.? Operating a RT 90 E and the boom seems to be very heavy at low degree angles not allowing much load capacity with 141 ft of main boom . Seems to be built to for capacities straight up at higher boom angles!
@johnnymimbs1492
6 жыл бұрын
free porn
@MFKR696
5 жыл бұрын
@@intellidog58 *All* cranes are built for capacities at higher boom angles. Going below 45 degrees is a real quick way to eat shit. It's not a tower-crane. By the way you're talking, I have a very hard time believing that you operate anything bigger than a pallet jack.
@intellidog58
5 жыл бұрын
INF1D3L010 Well your correct , I’m use to operating crawlers with main boom and luffer ! Dip Shit 🖕
@theworldsbonkers
6 жыл бұрын
Grove Left trigger ABAC Confirm lol
@matthew413
5 жыл бұрын
You'd hold your right Deadman switch for abac! Left would be babc
@Abangjoe778
6 жыл бұрын
How many tan this
@Ос-д5ь8ь
5 жыл бұрын
Блин, я подумал это техника без шасси, мм.как акзалос это гусеничный кран
@katsu7846
7 жыл бұрын
あとカッコいい
@gaborhertelendy3007
3 жыл бұрын
Grove gmk 550 0
@ibelieveyou2066
4 жыл бұрын
Gave up after 30 seconds.I saw too much handballing.
@THEWOODS3
5 жыл бұрын
That’s a lot of fucking about that
@shahzadfarooq6652
6 жыл бұрын
No good gmk355 and gmk5130 because thees model no ato sewing breaks
@PeterAlexanderWelch
6 жыл бұрын
I am sure the operator could take as many sewing breaks during the day as he chooses. You need to be more tolerant of others choices in life.
@lennyc624
6 жыл бұрын
Peter Welch, trying to make it through the day with a torn garment can be very frustrating. The importance of sewing breaks can't be stressed enough.
@shahzadfarooq6652
5 жыл бұрын
@@PeterAlexanderWelch your right but I said that gmk3055 gmk5130 auto swing break is necessary for that models .every other models have these swing breaks but these models have not .I request to Grove that they have to make auto sewing breaks because these are very important Thanks
@shahzadfarooq6652
Жыл бұрын
Your right
@KennyW285
8 жыл бұрын
One day looks about right, probably a little bit less.
@manitowoccranes
8 жыл бұрын
+Kenny Wong It takes roughly 2.5 - 3.5 hours depending knowledge/ experience with the equipment
Пікірлер: 48