Really it is great video. In which cases, should be using Torque Mode in VDF ?
@automationdirect
2 жыл бұрын
You would use Torque mode anytime you want Torque to take priority over speed. Winder, rewinders, capping, and web applications are some good examples of when torque control is utilized.
@winddopreview
3 жыл бұрын
Many thanks for that video, it will help me. May I suggest that after an introduction video, you add a detail video on parameters that influence the torque mode. (Bias, ASR...) Regards,
@automationdirect
3 жыл бұрын
Thanks for the feedback. We do plan to do a more advanced tutorial. It's just on a very long "To Do" list. You query will help move that up the priority queue.
@eduardoangel3152
3 жыл бұрын
I have troubles setting the torque mode, i would like to see more videos about this, thanks
@automationdirect
3 жыл бұрын
Thanks for the feedback. If you are still having issues, please contact our free tech support folks, they will be happy to help you. community.automationdirect.com/s/contactsupport
@yogeshkarkar007
Жыл бұрын
thanks. i had done my project with showing your hints
@automationdirect
Жыл бұрын
We are glad you found the video helpful. Make sure to check out our other videos at www.automationdirect.com/videos
@glennjameson2676
4 жыл бұрын
Nice informative vid! Cool demo
@automationdirect
4 жыл бұрын
Thanks for the feedback! Did you know that we have over 1200 automation videos like it at: www.automationdirect.com/videos (Random Search) www.automationdirect.com/cookbook (By Topic)
@societeenergie5193
3 жыл бұрын
Very instructive video, thank you for sharing
@automationdirect
3 жыл бұрын
Glad it was helpful! Did you know we have over 1200 tutorial videos like it at: www.automationdirect.com/videos ......................... By topic www.automationdirect.com/cookbook .................... By Subject
@aymansaad7429
3 жыл бұрын
How can I make analog set point for torque to overcome less torque at low speed That make motor jerk or not able to start
@automationdirect
3 жыл бұрын
Hi Ayman, Take a look at Parameter 3.00 (A1) or P3.01 (A2) option 3. I think that is what you are looking for. There are other options in there that you might be interested in too.
@aymansaad7429
3 жыл бұрын
@@automationdirect thanks for interest I have drive motor when operates at frequency below 50 HZ with load it can't start i need to increase torque. I increased torque boost but nothing occurred what is the parameter that concerns this.
@qzorn4440
4 жыл бұрын
great video... it looks like this could replace loadcell torque feedback on drag braking action on heavy paper roll let-off unit instead of fraction drag brakes...:) also the drive keypad seems better than rockUNwell hmi keypad that fail from poor membrane button design.. which requires a new hmi for new/old non-working drive...:/ thanks AD
@automationdirect
4 жыл бұрын
Yeah, this is a cool feature to have in a VFD. Yet another reason the GS20 is such a great value! Did you know that we have over 1200 automation videos like it at: www.automationdirect.com/videos (Random Search) www.automationdirect.com/cookbook (By Topic)
@jaikrishna741
Ай бұрын
Do you have any calculator for this? thanks in advance
@automationdirect
Ай бұрын
A calculator for which part of the video?
@aymansaad7429
3 жыл бұрын
Great work
@automationdirect
3 жыл бұрын
Thank you so much 😀
@yogeshkarkar007
Жыл бұрын
IT IS POSIBLE TO MAKE IN DELTA MS30 DRIVE?
@automationdirect
Жыл бұрын
Yogesh, We do not sell the Delta MS30 drives. Thanks
@mihaiadam2978
3 жыл бұрын
great job
@automationdirect
3 жыл бұрын
Thanks! Did you know we have over 1200 automation tutorial videos like it at: www.automationdirect.com/videos ............ random search www.automationdirect.com/cookbook ....... organized by subject
@monachanlukose6048
2 жыл бұрын
Please translate in hindi
@automationdirect
2 жыл бұрын
Did you know that KZitem already does this for you? In the lower right corner of the video, click on the little gear icon. Click on "Subtitles/CC" Click on "Auto Translate" Click on the language you want.
Пікірлер: 27