This video is exactly what I needed. Will be using this for the reverse wiring for my manual swapped GS300. Also has BMW 6speed ZF gearbox (from E46.)
@JeromeArcher-rd4ws
27 күн бұрын
Hey bro I’m about to pick up an 01 here in a few days and I appreciate this video this has me hyped
@lakaies174
Жыл бұрын
My dude, thank you for the reverse lights wiring, also very good to know about the Wilwood cylinder, but from my research it says that the E9x slave cylinder and CMC bore is 3/4"? I see you're using a stainless steel clutch line, which one did you use to fit the CMC to the ZF slave cylinder?
@OhToeKnee
2 ай бұрын
thinking of doing this to my gte single turbo stock ecu gs300 wondering if it runs just fine with stock ecu at WOT with just jumping the neutral switch wires.
@jaguvaari
Жыл бұрын
Hi, in your previous post you mentioned/ revealed the gearbox rattle issue....and to do something to eliminate it.... I have a 71 Mustang with a 429 V8 making ab. 650 hp/750 Nm and having a Tilton 3 disc rigid discs and a lightened steel flywheel on the engine side and after the gearbox GS6 53DZ I have rigid steel flange and a prop shaft with longitudinal movement to eliminate the rigid rear axle movement. After installing the gearbox I noticed the same gearbox rattle as you had. Did you do something to cure the rattle and what actually is the reason for the rattle. You comment would be highly appreciated. I also invite others to comment this issue which is. a bit embarrassing as it sounds unhealthy although the gearbox otherwise works completely fine.
@ChefNorrawitJ
Жыл бұрын
Hey Bo , do you have the part # for the willwood master cylinder
@EdsonHenry
Жыл бұрын
Appreciate this video. I have one question. Did you have to run an AUTO to Manual Module so the car can run with the stock ecu?
@BoBuilds
4 ай бұрын
No it ran perfect fine for me
@UninhibitedAuto
2 ай бұрын
Which zf transmission did you use??
@user-tz5mm4vr2x
5 ай бұрын
Did you get that trans mount somewhere or did you make it?
@BoBuilds
4 ай бұрын
It’s from Collins adapters
@liamcooke5513
8 ай бұрын
Hey mate, did you end up doing something with the handbrake? Im looking at doing this swap in the future and the handbrake is my only concern
@BoBuilds
8 ай бұрын
i got an E brake handle from an 06 mustang from Amazon. work fine with the original e brake cable
@BoBuilds
8 ай бұрын
just had to reroute the cable and i mounted the e brake handle on the driver side of center console
@ORCChannel
9 ай бұрын
Can you write full code of this gearbox because bmw have so many zf gearboxes
@BoBuilds
9 ай бұрын
GS6-37bz
@ORCChannel
9 ай бұрын
@@BoBuilds thanks
@dannyrodriguez6396
6 ай бұрын
What driveshaft are you running from the trans to diff
@BoBuilds
4 ай бұрын
Telescoping 54” steel shaft, custom made
@jbjdmcruiser23
4 ай бұрын
Question tho, will you accept another customer? I need mine to be done.
@BoBuilds
4 ай бұрын
Where are you located
@josevaldez7281
Жыл бұрын
What converter you running in the truck Norris 5.3
Пікірлер: 29