Thanks for this. I took my blades off to clean and couldn't figure out what position they need to be in to reinstall. Got a date with a hottie and needed a quick trim.Looking good now. Phew. Appreciated.
@jjkarwowski
2 жыл бұрын
I noticed my Wahl being noisy so I loosened the screws and it suddenly ejected off like a sling shot! All the blade and components holding them together blew apart like a grenade. I attempted to put it back together, but trying to place the spring back inside threw me a giant curveball. I couldn't get it set right. I watched over a dozen Wahl KZitem DIYs and not a single one discussed it or showed a close up. I was about to give up, until I watched your video. I know you didn't go into detail about the spring, but you had just the right closeup angle and it was enough to help me put it back together successfully. It now hums like a gentle hummingbird. Thank you!
@brianmeinking2723
3 жыл бұрын
My girlfriend had taken apart the blades to clean and re-oil but had forgotten how to reassemble it. We both watched this video and learned a lot. We reassembled and aligned the blades then applied the oil. Thanks for the great video!!
@donnadavis9934
3 жыл бұрын
Thank you for sharing this video! You demonstrated in such a clear and simple way. I had taken ours apart to clean them but have been afraid to use them since bc unsure if they were put back Together and adjusted properly. after watching your video I reassembled them per your instructions and they're working great!
@Sarah-hz3gy
3 жыл бұрын
Thank you, the way that you showed the blades up closely with plenty of light, how they were to be aligned properly etc... very helpful! It wasnt easy to keep blades in position and still, until screwed in tightly, however perseverance pays off!!! Thank you again :)
@adysen
3 жыл бұрын
Outstanding and easy to follow tutorial. Thank you for teaching me how to care for my hair clippers the correct way!
@shelby3822
Жыл бұрын
Thank you - took mine apart to clean and didn't adjust... started biting my neck immediately
@bembesully8360
Жыл бұрын
Now that's the details I needed..thank you
@matthewbuzzard4024
2 жыл бұрын
Thanks. I never knew that u had to do all of this
@JockeyCake
Жыл бұрын
Excellent video. Thank you
@russ1669
2 жыл бұрын
great and clear instruction thankyou
@duragggura3695
3 жыл бұрын
Great Video...clean cut instructions..kudos!!!
@MegaSafetyFirst
3 жыл бұрын
Thank you, I appreciate your feedback! 👍
@alexiariley2827
3 жыл бұрын
This helped so much thank you!
@johnvicars9382
2 жыл бұрын
The white component, along with its spring (situated in the cavity beneath the blades) popped out as I was removing the blades, and I can't figure out how to re-attach the spring to the white component. Any suggestions?
@baselkaskas2093
2 жыл бұрын
Fk mine too did u figure it out 😂😂
@deficoinfx7863
3 жыл бұрын
Thanks for the help
@annakortukov2845
Жыл бұрын
Thanks, great video! 👍☺️
@noy5626
6 ай бұрын
Thanks! Helpful video 👍
@ramonmaldonado7570
Жыл бұрын
Thank you for the vid
@rudygonzalez7690
3 жыл бұрын
I followed the instructions in the video as best I could, but the top blade is loose. How can I fix that?
@tshepontlhane8882
2 жыл бұрын
Good afternoon I wanna know how to assemble from the inside
@IM-xg2ki
2 жыл бұрын
So nice, thank you! YOu saved me! :D
@Poraqui
25 күн бұрын
I've noticed that the bottom blade (the one with screw holes) has uneven "big teeth" at the extremities. Is this feature there to know which side we should align the blades to? In this case the author aligned the first teeth of the upper blade to the small "big teeth" of the bottom. Is that the standard procedure? My Rowenta clipper also has the same configuration.
@shinobi6r
2 ай бұрын
Whats the name of the plastic piece w the spring where can i find it for the andis envy clippers
Пікірлер: 27