1. Enlarge discharge hose diameter +25-50% larger than inlet funnel diameter 2. Move Suction section near discharge end. 3. Make venturi section adjustable to allow optimization.
@themanwhoneverfoundgold.3860
8 жыл бұрын
Nice instruction vid there, mate! I have got the pipes, and a building plan, but lack some small pieces, like the stop lid on the collecting part. My idea is to have a thinner sucker pipe as a front piece. I`ll proberly make a tip on the suction mouth in metal, with some inwards bent triangels. Just to prevent the bigger rocks to go into the system and block the pipes. Still haven`t found alluvial gold yet, but already started making a "bazooka" fluid bed box in aluminium. 80 cm in length. Also bought a plastic drop riffle sluice box, and waiting for another kind of metal sluice box to arrive. Looking foreward to the spring now. Still much snow here.
@southpawsgoldprospectingan4092
8 жыл бұрын
+The man who never found gold. Lol you have gone sluice box mad ;-) The plastic drop riffle work well where did you get it? I want to do a bazooka type too Yes put some mesh or something in your nozzle I dont have the problem with the big hole but I would be with the smaller tube. Check the moss at high water level on the inside bends. Going next week to get some.
@themanwhoneverfoundgold.3860
8 жыл бұрын
+Southpaws gold prospecting and adventures Here`s the drop riffle thing I bought. Have tried it and it collects the heavy stuff very well. www.ebay.com/itm/Eldorado-Gold-Sluice-Box-Professional-expert-Gold-Prospecting-Equipment-/252296961778?hash=item3abe121ef2:g:uvIAAOSwgQ9V4zxN I love DIY-stuff, so I went for making a bazooka thing here. Got this sheet of aluminium from a friend, and what else than a fluid bed box could I make of it, hehe.. Made a small model 1/4 size in cardboard, and will do some improvements and small changes with the full-sized box.
@southpawsgoldprospectingan4092
8 жыл бұрын
Cheers mate I will have a look shipping and tax makes everything stupid prices here. The DIY stuff is best I am trying to figure out how to make a bender to bend the sheet aluminum. I have seen some stuff. I am just starting some tomatoes f3 ;-) Hope all is well with you mate I know you had some bad times this year and last. Go and find some gold. I would like to see your box. I have a job interview tomorrow bit nervous..
@sirwilliamofpennylot
6 жыл бұрын
Flapper valves work pretty good, choker valves work even better. Remember to have your outlet hose connected when testing because you need water in the outlet pipe to make the outlet valve close when you pull the upstroke. A lot of people forget this when testing their new invention and think it doesn't work. regards Bill
@southpawsgoldprospectingan4092
6 жыл бұрын
Thanks Bill good info. All the best Dave.
@bayoubilly6971
8 жыл бұрын
I've seen the stright style gravity dredge it works well but you need lots of hose and drop. It works well actually. Nice hand dredge.
@southpawsgoldprospectingan4092
8 жыл бұрын
+Bayou billy Cheers I have seen them too. I am hoping the way I want to try will give me a bit more suction by using a funnel flair at the top I dont want to have to pack 300ft of pipe lol but the drop is the most important thing. I have to give it a try I know it will work in some places better than others.
@fannycubells6747
7 жыл бұрын
hello,i'm a french prospector and i live in south of France. here we can't use any motor to dredge and when i looked your vidéo i have made your system, it run very well ! not on a long distance (2 to 3 mètres ) and with big suction. so tank you for this great idea
@southpawsgoldprospectingan4092
7 жыл бұрын
Hay thanks we are the same here no motors. I would love to see a clip of it working. Good luck with the prospecting. Dave
@fannycubells6747
7 жыл бұрын
Southpaws gold prospecting and adventures OK , i'll try to make a clip sunday if weather Will be good, but i'll make it with my phone because i have no camera ...
@southpawsgoldprospectingan4092
7 жыл бұрын
Most of my filming is done with a Phone. Hope the weather stays good I want to be out on Sunday too ;-)
@TheNimshew
6 жыл бұрын
kzitem.info/news/bejne/z6-gwJWFsqZlfaw
@beyondinfinity5601
6 жыл бұрын
where in france do u prospect.? i would love to find a prospecting partner for to go prospecting in france sometimes.
@daveuk2560
7 жыл бұрын
u dont need that much of a river drop mate. submerge all the flexi pipe in the river until the river is running through it, raise downriver end and presto. have some kind of mesh over the suck end for big rocks, also have some kind of heavy weigh around for when u want a break, if the front end sucks air it stops. flexi pipe works best ofc but remember the natural riffles in the pipe, be sure to clean it out every now and then :) used this method for many times. you will need something to slow the flow on the box as alluvials will be going tooooo quick, hope this helps.
@southpawsgoldprospectingan4092
6 жыл бұрын
Thanks for the info.mate ;-) I want to be able to work close to the sluice with this. Just so I can see what I am running and getting.
@DaleCalderCampobello
8 жыл бұрын
Now I see how the pump works. The new theory makes sense to me hope it works as well in practice.
@southpawsgoldprospectingan4092
8 жыл бұрын
+Dale Calder It is more of a suck than a pump but it gets the gold off the rock where a shovel would not. I am going to have a play around with the siphon dredge over the summer might just save my back. It will only work in certain areas but if I can do it on the cheap well worth a try its not like we get lots of gold here. Its all fun as long as I dont get arrested ;-)
@TheNimshew
6 жыл бұрын
With the hand dredge, I say use a wye fitting turned around. Take an 1/8 th bend and make an 'H' fitting. Have the suction side coming from the side inlet and the discharge straight ahead. That way, any material that comes up drops into the straight part below the piston. All the other hand dredges, the discharge is offset.
@paulm1813
8 жыл бұрын
My wife will go mad if I dismantle the kitchen sink to make one of those :)
@southpawsgoldprospectingan4092
8 жыл бұрын
+Paul Marvin Dont do that lol. Its nicer to work with when its new and not slimy.
@MrDazP1adv3ntures
8 жыл бұрын
I need to make one ready for my inaugural season
@southpawsgoldprospectingan4092
8 жыл бұрын
+MrDazp1 You need one for rock you can not get the gold off the rock with a shovel. The gold will lay on the rock like it lays on the miller table. Get a hand brush too so you can sweep the beds rock and get the stuff together.
@eastcoastcarpenterofalaska5073
5 жыл бұрын
Look up Ram pump, it uses a pressure tank and one-way valve can build up to 70 PSI, that's how I'm going to do some good sluicing in the backcountry
@richardchase4019
3 жыл бұрын
That is a very good idea....
@akbychoice
2 жыл бұрын
Seems the 45° should be put on in the opposite direction
@robbostreasureadventuresen8916
8 жыл бұрын
Thinking outside the box Davey. You may be on to something brother. ATB mate Robbo
@JanTheDetectorist
8 жыл бұрын
Hi dave, you should throw an eye on jabsco joker valves for a one way manual pump system
@southpawsgoldprospectingan4092
8 жыл бұрын
+Jan The Detectorist Thanks Jan I will Have a look. Cheers.
@meehan302
8 жыл бұрын
Thumbs up Davey
@southpawsgoldprospectingan4092
8 жыл бұрын
+Patrick Meehan Thanks Patrick
@dionata6805
6 жыл бұрын
Por favor coloque a list de materias por escrito se puder obrigado
@TheNimshew
6 жыл бұрын
So you want to make a bazooka? If you had a 1" pipe coming in at an angle from a gas pump. How many feet per sec? Then, water is .433 lbs per foot. 100' = 43.30 lbs Go online and search for tables (psi/feet per second)and pipe size.I'm not looking, but I'd make a guess of ,at least 50 psi. The drive line would have to start above the bazooka about 135 feet vertically to get 50 psi at the bazooka. It can be done, but, wow! You'd have to run a whole lot more pipe(unlless it's a vertical cliff)Plus, you need the flow ABOVE to be substantial. It'd suck a swimming pool dry in a minute. No piddling creek would do.
@southpawsgoldprospectingan4092
6 жыл бұрын
Man I wish but we can only work with hand here no power. Would be fun though until the 5k fine lol
@TheNimshew
6 жыл бұрын
Any motor is not allowed in California for dredging. You aren't allowed to use a shop vacuum(though I see nothing wrong with collecting material from above the water line, taking it home and panning it) Still, not allowed.
@TheNimshew
6 жыл бұрын
There's a video of a syphon dredge I think it's 49er... something. 800' vertical head.
@TheNimshew
6 жыл бұрын
kzitem.info/news/bejne/z6-gwJWFsqZlfaw this one
@southpawsgoldprospectingan4092
6 жыл бұрын
Thanks thats some setup. You hit the nail on the head i would need a lot of pipe to get it set up. I will stick to the old shovel I think is just for fun.
@lifeinthailand
8 жыл бұрын
Hope you didn't find any gold in the garden sand, That would be bad for you and the family...lol
@southpawsgoldprospectingan4092
8 жыл бұрын
+lifeinthailand I could just have sand delivered by the ton sit at home and pan it ;-) Never have to leave the house lol.
@JadesAdventures22
8 жыл бұрын
hay do you make them for ppl and sale them
@southpawsgoldprospectingan4092
8 жыл бұрын
No just made them for myself but work well ;-)
@JadesAdventures22
8 жыл бұрын
if i pay wood you make the man bits of it for me
@southpawsgoldprospectingan4092
8 жыл бұрын
Would cost to much to post mate.
@fannycubells6747
7 жыл бұрын
hello dave, il gone prospecting Last week and made a clip... it was not long because batterie low .my son send it next week because I don't non how ! bye
@southpawsgoldprospectingan4092
7 жыл бұрын
Hi fantastic thanks look forward to seeing it ;-)
@TheCominghome
6 жыл бұрын
It wont work, why don't people try things before they waste their time making a stupid video on it.
@southpawsgoldprospectingan4092
6 жыл бұрын
Fanny Cubells This guy made one and it works. Try and keep your comments polite. Happy new year ;-)
@GoldPanningIRE
6 жыл бұрын
It will work it's the same concept as I used for bilge pump drive dredge I tested at home. 1&1/4 PVC to a Y connector with a funnel on the inside. after fine tuning the sweet spot is found, the pressure of the water passing this point is enough to suck gravel in. Just make sure the output in larger than the input so a 1&1/2 inch Y would be best with a reducer for the section to 1". As regards the funnel - Drill a hole in a small bottom a rectangular plastic bin and dam up the area with rubble bags. Result is 100% gravity powered suction dredge. I will do a vid on this during the summer as I have all the parts already
@southpawsgoldprospectingan4092
6 жыл бұрын
Thanks. One guy built one last year in France and showed me a video of it working ;-) I would be very interested to see your build all the same. Thanks for the comment.
@richardchase4019
3 жыл бұрын
LoL....your comment is as stupid today as it was two years ago, you rude little prick.
Пікірлер: 52