Thanks Dan. I'm retired too and have a new Hangkai in my shed ready for me to fire up. It helps when somebody else has been to the trouble of trouble shooting problems, to reduce problems for other people.
@BoilerDan1
6 жыл бұрын
Great encouragement for me! I'll be adding more.... The pull start has a defective plastic piece that comes lose. It can result in the pull cord catching when you release it too fast (Mine did and broke the cord. Solution. glue that little guide into place and wrap it with a little electrical tape too. I'll make a shorter video soon showing exactly what happened and the fix.
@dennisalexis4452
5 жыл бұрын
Hi thanks for the tutorial I was given a 3.5 older mode, l had to check it out but runs fine no problems I didn't know about the oil next to the prop so will check it tomorrow. Keep up the good work.
@Steve-fz3pl
5 жыл бұрын
Thanks Dan, very usefull videos, just wish I had seen it or spent the time to look over my Hangkai 3.6HP before taking it out. I have mine mounted off the side of a canoe, its really just an inexpensive project. First failure was the choke setting. After inspecting the air filter I realised the choke settings were backwards and got it going in a bucket. Next time out my pull start and claw pawl failed with bits everywhere. $20 on ebay and I’m good to go again. Maybe this time. Ive added marine grade 75-90 gear oil to the gear box. Marine grade silicone grease to the seals and shaft. Pulled the water pump apart and coated all surfaces with the silicone grease and put it back together with thread lock. Couldn’t get a NGK-BM6Y, got a NGK-BPMR7A and a Honda/Denso W22MPR-U.
@BoilerDan1
5 жыл бұрын
Thanks for sharing. I didn't indicate in my early videos that when using a bucket, make sure you keep the water cool. Running a hose so it doesn't overheat. I actually kept adding snow and ice but failed to show that. Sounds like my videos have helped! Especially on the backwards choke! Also put some new wax on that pull cord, it will last a lot longer..... Mine shows no wear at all (0:
@Steve-fz3pl
5 жыл бұрын
Thanks Dan, the water stayed cool, started fist pull. Thanks, my cord came waxed as with the spare, the new one wasn’t though. I was tempted to canabalise into an electric and like the look of the Hangkai 4HP electric I found on Aliexpress but Ill stick to the gas for now.
@user-hb8be5wb4q
5 жыл бұрын
Oh, while you got it running, you could cruise over to the neighbors, 3 houses down, your brother is in his boat, but needs a tow back to the main yard. The neighborhood kids are complying he is disturbing their snorkel class in the snow. Brahaha! All these small 2 cycle motor have their quirks, but when broke in, they are great. I had a 7 hp Eska back in 1973, it ran good and powerfull. Enjoyed it very much, especially after I got the bugs worked out. Thanks for sharing this video.
@BoilerDan1
5 жыл бұрын
Thanks for watching. I hope to take it on a full day (downstream journey) passing by a little cabin my parents had along the Tippecanoe River. Just waiting for water levels to return to normal! It'll be about a 20 mile trip, so it should be a good test of the motor now that it is broken-in. Speaking of the "snow snorkel class", I remember taking an old V bottom boat of my dads out in the winter when there was a thin sheet of ice extending out on the river about 10 feet. I went slow, pretending the boat was an ice breaker and chipped away at the ice. It was an old two cycle motor on it.... Wish I still had it! But I wouldn't repeat the bit of foolishness again! …...What were my parents thinking :0-(
@MrRaab-hu9rs
5 жыл бұрын
Thank you for the review and detailed "take apart". The build quality scares me. You just saved me a couple hundred bucks.
@BoilerDan1
5 жыл бұрын
Mr. Raab I’m glad you found the review useful. Although I am very happy with the motor, I understand you not wanting to take the risk or messing with it. For me it’s an adventure! Thanks again for watching.
@Okinanam69
Ай бұрын
No guts…no glory! Hangkai separates the men from the boys. It is fun…because it really is a Honda motor under disguise!😊
@Okinanam69
Ай бұрын
The name should have been “Hond-Kai.”
@BoilerDan1
Ай бұрын
@Okinanam69 Ha😂. You nailed it! You’ve got to love tinkering and then you’ll enjoy the adventure!
@grahamhall2662
2 жыл бұрын
Excellent review thank you. Don't think I will get one, don't fancy risking my life half a mile out to sea. You helped me to decide on this engine.
@BoilerDan1
2 жыл бұрын
Thanks, glad to help! I wouldn’t take it out to sea either!👍👍
@RC-hm9vg
2 жыл бұрын
I'm going to get one of these. Seems pretty straight forward. Worth the expense and time. I'm going to use it on a Paddle boat. Great detailed video. Thanks
@BoilerDan1
2 жыл бұрын
They seem to work for some, not for everyone. But if you tinker with motors it’s works fine. The clutch is an issue, but swapping out the tension spring helps, and regularly replacing it! Not hard to work on… Good luck with yours, and thanks for watching 👍👍
@Truebluexpat
5 жыл бұрын
Best review I have seen yet, thank you
@thisismecantuseeitsacz5823
5 жыл бұрын
The best Review I have seen thank you for sharing
@BoilerDan1
5 жыл бұрын
Thanks! Stay tuned, I'll add more as any issues present themselves.
@28ebdh3udnav
3 жыл бұрын
Thinking of buying a small personal boat so I can visit the river and lakes here in my area
@BoilerDan1
3 жыл бұрын
I would recommend something a little more solid than the raft I put together. I lost thrust because it to squishy. So spend a little more and find a better design! Thanks for watching 👍
@Ibanezflyingfingers
3 жыл бұрын
To pull out the starter rope for maintenance, just pull it out and tie a loose removable knot in the rope near the starter housing. Also although it has a water pump, this machine is actually air cooled. The water pump only cools the exhaust tuner. It won’t harm the engine to run it without water pumping but it will melt the cowling and stuff
@BoilerDan1
3 жыл бұрын
Good to know regarding the cooling system! Thanks for watching and taking the time to provide some valuable information!👍👍
@jimcatx3090
5 жыл бұрын
Great video you seem like a great guy I love to tinker and upgrade thinks myself thank you
@BoilerDan1
6 жыл бұрын
I was getting ready to do a 25 hour run time review. When I removed the cover to pre-inspect the motor, one of the fuel lines broke off. I will definitely add in a recommendation to change the fuel lines at the time of purchase. It did spew gas around until I removed the cap to relieve pressure.. Could be a serious fire risk if there had been any spark around. I'll cover this in my next video post.
@raniasuesi9026
4 жыл бұрын
from where did you buy the fuel lines?
@BoilerDan1
4 жыл бұрын
Ran Sue : Fuel lines from Amazon. Here’s the link. HIFROM Replace 4-Feet Fuel Line Hose Tube (4 Size) I.D. x O.D. 3/32" x 3/16" 1/8" x 3/16" 1/8" x 1/4" 0.080" x 0.140" for Poulan Craftman Chainsaw String Trimmer Blower www.amazon.com/dp/B01LPSP00U/ref=cm_sw_r_cp_api_i_z5ebFbNK2W8W3
@raniasuesi9026
4 жыл бұрын
@@BoilerDan1 Thank you sir
@jimqian5205
4 жыл бұрын
Why no lube when you got it? Now I know. Because shipping don’t allow oil to go.
@deweylee2449
5 жыл бұрын
Hey Dan. The idea of a filter for the intake of the carburetor is a mute point because outboard motors don't use an air filter anyhow . The environment that they operate has little dust and there is to much of a chance of moisture getting them wet and choking the airflow. All and all a great review and informed review. Thanks and we will be awaiting the on the water review.
@BoilerDan1
5 жыл бұрын
Not the first to point that out to me. Fortunately I had not changed it, and I will leave as is! Thanks for watching and taking the time to comment. I hope to make a full day journey on a small river that I'm familiar with (Tippecanoe River)... Once the water levels come down to normal!
@7o177
5 жыл бұрын
cheers for the info dan me and the boys are making plywood boats this summer and the cruize n booze will be on.
@rolkamon
5 жыл бұрын
Thanks for the review, very informative, Im gonna add my comments here as this seems the best resource regarding this engine on the net. Like a 60’s era car this engine is very simple so if you have any mechanical inclination your gonna be able to deal with it. Its a 200$ motor where as something high quality is gonna be a minimum of 4x more expensive so im not gonna criticize its crudeness, for 700$ im gonna deal with it. The engine is listed as water cooled but its really not sure there is any circulation through the block, the thing is a loud screamer like a fully air cooled. The water cooling might just be injected to cool the exhaust. There seems to be some sort of inertial transmission where at a certain rev a gear engages that will turn the prop and engage the water pump. This presents difficulty at docking as you have no steering or propulsion at low power. Also not sure the type of transmission or clutch geared or friction. Gets very low propulsion at anything less than full power. I have this on a dinghy i transit to my sailboat on a mooring. I have to deal with wind currents and chop, at full power the engine moves the boat well but at anything less its nowhere near good enough. The power curve is a hockey stick at 90% power.
@BoilerDan1
5 жыл бұрын
Nice review. The transition you mentioned is inertia. There have been some comments on mine making metallic noise. Actually I discovered that the quick fasteners that I use on the metal side poles have the metal hinge vibrating on the metal pole causing that noise on the video. That being said, you can hear the clutch as it is partially engaged at slower speeds. The water pump system is also very simple, no gears, it just fits over the square shaft leading to the gears for the propeller. I'm planning on a video this fall of how to disassemble that area an replace the pump wheel. Not that it's needed, I'm just having fun with the motor. And yes, full speed or idle are about your only options with it. Thanks for responding.
@rubenvor
4 жыл бұрын
Outstanding detailed review! Thanks for taking the time and share such valuable knowledge and information. I was planing to buy a 2.5 suzuki to put on a excursion 5 inflatable boat, but after watching this video, I'll definitely get one of these hangkai 3.6. I'll make sure to change those ful lines for better ones. Hopefully it will do fine with salt water. Thanks.
@BoilerDan1
4 жыл бұрын
Some additional things to consider is the clutch system is very weak and wears out quickly. Changing the tension spring will add a lot of life to it. You can see the change I made in my video on putting in a new clutch (actually two video's, one removable and the second installation. Not a difficult task as I'm not a mechanic and was able to figure it out on my own 😂. But I'd consider ordering a spare clutch to have available. Regarding saltwater.... I've seen complaints that the water cooling tub rotted out? Again, it's a simple tube that you could replicate with a similar diameter copper tubbing... Running the motor in a tube of fresh water when on shore would flush it out.... There is a 4 hp hangkai out there that is air cooled. Might be a better choice? I've got several video's out on the 3.6 hp, so keep my link handy for things you might run into if you do get one. Don't over pay... I don't think it's worth $300. I paid under $200 and was happy with that even with some of the issues. I appreciate your taking the time to provide positive feedback for my efforts. I was just documenting my journey... Not realizing how successful it would be! 👍👍. 1. Clutch replacement - kzitem.info/news/bejne/qWqjtnurfn2ffn4 2. Clutch installation - kzitem.info/news/bejne/sqtvtZ6Om3-mp3Y
@rubenvor
4 жыл бұрын
@@BoilerDan1 Thanks a lot Dan. I think I have watched all your videos. I'm a car mechanic, so hopefully won't have any problems with those parts replacement. I have one last question, can you tell if a 6hp motor will be too much for one of those excursion inflatables? For me, it seems the restriction is the motor mount that comes with those boats, but I'm guessing with a sturdy mount connected directly to wooden floor and to the boat mounts, and that goes over the inflatable might be possible. What do you think? And thanks again for all the great videos!
@BoilerDan1
4 жыл бұрын
rubenvor : I’d be concerned about it handling that much power. The index brand is a entry level raft. There’s some sturdier ones out there. But yes if you can mount the motors weight and thrust to the wood floor it definitely would help. But I’d seriously consider a more sea worthy raft 👍
@markbrown7449
2 жыл бұрын
Dan, I read somewhere that this little motor is really a "1.5".. Either way, it'sa step upfrom a electric trolling motor. Even though I don't need one, I'd still like to have one. My fishing buddy gave me his "OLD" jon boat. As long as it gets me to where I wanta go to and back, this motor is for me .. Thanks man
@BoilerDan1
2 жыл бұрын
Point A to point B it will do. It should push a Jon boat a lot better than an air filled raft! It’s a bit noisy but it sounds good for what you’re wanting to accomplish. Thanks for watching 👍👍 There are little issues so I encourage you to watch more of my videos…. Especially on replacing the clutch. I’m no mechanic and am able to do it. Parts are available through eBay and some from Amazon too 👍👍
@djassisti
3 жыл бұрын
Thank you very much for the 2 videos, they were very helpful :)
@BoilerDan1
3 жыл бұрын
You’re welcome! Actually there are 16 videos that I produced, several are of repairs. Here’s a link to the series to help you find specific information about the motor. kzitem.info/door/PLjMZtm2hvqrOIvLcah1u1V45Y_R-AKeqm Thanks for watching and taking the time to comment.👍👍
@bwyyy7306
5 жыл бұрын
I just bought a 1985 Johnson 4.5 ho two cylinder for 300 CAD, it’s had little use and runs great, I thought about a Chinese motor, but the Johnson will run for years, even tho that engine is new, you don’t get any warranty
@4shorefishing779
4 жыл бұрын
Thank you for your great in-depth review!
@BoilerDan1
4 жыл бұрын
You’re welcome. I’ve made several videos on my journey with the motor. You might want to watch most of them before buying one as I’ve covered several issues with it! Thanks for watching.
@4shorefishing779
4 жыл бұрын
BoilerDan1 watched several so far lots of good info!
@michaelgonzalez249
6 жыл бұрын
I have had zero problems with my hangkia 3.5. It did not have oil in gear box that was easy fix. Also replaced plug wires cj8 replacement "E"nergy premium plug from Home depot. Aside from that engine as easy to maintain as garden " weed whacker." On my inflatable Sea Eagle ex380 we fly along. Easily 7-9 mph depending on tidal flow.
@BoilerDan1
6 жыл бұрын
I'm very happy with mine too. I have yet to run it in a calm water environment like a lake or pond. No tidal flows in Indiana! :0) I agree, the motor is a very simple design, and parts look easy to come by via eBay. I hope to soon get on a small lake and see how it does in calm water. I expect the 7-9 mph you described. Thanks for watching and commenting.
@atgtowing4367
2 жыл бұрын
thanks so much you answered all my questions!!!
@BoilerDan1
2 жыл бұрын
You’re welcome. I’ve made several videos on my experience with the Hangkai motor. It’s not for everyone, but I have enjoyed playing with it! Including a few repairs 😂 Thanks for watching 👍👍
@KayakQ
4 жыл бұрын
Great Video! Super helpful with all the information that you have provided! Thank you!
@BoilerDan1
4 жыл бұрын
You’re welcome. I’ve made several follow up videos on the motor including some repairs so keep watching! Thanks for taking the time to comment.
@SD-rs6qn
5 жыл бұрын
The first good video on KZitem about this outboard. Thanks, it was very helpful.
@BoilerDan1
5 жыл бұрын
Thanks!
@saidhadi7875
4 жыл бұрын
Vey helpful video. It is much much better than the manual which comes with the motor. It is also the best demonstration available online. Thank you very much
@BoilerDan1
4 жыл бұрын
Thanks, I’ve made several videos of my adventure. Some thoughts change along the way but all in all I’m still happy with the motor. Thanks for watching and taking the time to comment 👍
@SneakerShow24
4 жыл бұрын
Very helpful! Thank you so much!
@robertclark1868
5 жыл бұрын
I got mine in last season. Used it a few times. Decent motor, I ust need a bit more speed. Keeping it anyway though!
@BoilerDan1
5 жыл бұрын
It works well going downstream! :0)
@Etrician55
4 жыл бұрын
You should strongly consider marine grade gear oil, they have additives to help with expansion so it doesnt blow your seals out
@BoilerDan1
4 жыл бұрын
Good advise, Thanks
@thatbigskeptic
Жыл бұрын
Great video. Thanks for the info. I am looking into one of these.
@BoilerDan1
Жыл бұрын
They are not for everyone! But if you like to tinker, it’ll work. Might check out my repair segments too. It’s exhaust goes below the water line so it’s not great for trolling, but point A to B is fine. Thanks for watching and taking the time to comment 👍👍
@767dag
2 жыл бұрын
to honest it doesn’t look bad , i appreciate the review
@BoilerDan1
2 жыл бұрын
I had a lot of fun with it! Thanks for watching 👍
@philipblick8887
6 жыл бұрын
Hi there I have had some experience with servicing outboard motors, I suggest your comment about the air filter being inadequate is really not that important simply because outboard motors are never used in conditions where dust is an issue. Most outboard motors use some kind of spark arrester type of devise where an air filter would normally be fitted in case of backfire igniting leaking fuel.
@BoilerDan1
6 жыл бұрын
Thanks for the suggestion. I have not replaced it, so your input will be put to use :0)
@Q-BinTom
6 жыл бұрын
Thanks for sharing I am thinking of getting one for my Gheenoe
@BoilerDan1
6 жыл бұрын
I was motivated because of some negative reviews. In watching, many looked bogus to me. Like they had purchased a used one that had been abused to start with. I won't be using mine in salt water, but I've run it for about 15 hours and no problems that were serious. I'm keeping an eye on the fuel lines, and I did change the spark plug... But all in all, I'm very happy with it. I will make another video of it actually on the water with the Intex 4 raft that I have. Thanks for subscribing!
@gajumbo1881
5 жыл бұрын
Did you purchase one for your gheenoe?
@josephleister9198
5 жыл бұрын
Nice video, thank you.
@Hitech82
5 жыл бұрын
Great review pal. I almost bought one after watching your video. I came across a Mercury motor that runs great instead .
@BoilerDan1
5 жыл бұрын
Thanks. The used Mercury is probably a great choice. I'm actually happy with mine for the price, but still only go upstream on a river and not to far out on a lake... Time will tell, and I try to give an honest review. It seems like a simple design, and I like to tinker with stuff, so I don't mind at all messing around with it. Thanks for watching and leaving your comments.
@paulob5153
4 жыл бұрын
Your better of
@paulob5153
4 жыл бұрын
That is one noise revy motor
@colineasterbrook9293
4 жыл бұрын
Excellent video. Thank you.
@BoilerDan1
4 жыл бұрын
Colin Easterbrook : Thanks for watching and taking the time to comment. I’m documenting my experience with this little motor. Several segments available including repairs and improvements that I’ve attempted. So far she’s still running 😁
@BoilerDan1
6 жыл бұрын
It will work for your needs. Be sure to add gear lube and take your time breaking it in for several hours at medium and slower speeds.
@philmoody2445
4 жыл бұрын
Hi Dan, thanks a lot for your great work reviewing the Hangkai. I’ve recently purchased it on eBay and I am going to take it out for a fishing trip in the Netherlands. As you’ve recommended I’ll do some adjustments at the beginning. Concerning the isolation of the motor: how much does it reduce the noise and secondly does the motor heat up more compared to without isolation? I am glad you gave so many tips and hope that you’ll add some more experience.
@BoilerDan1
4 жыл бұрын
I ended up removing the noise deadening material. It made little to no difference in sound and I was concerned about it over heating. Hope yours works out well! Thanks for watching and taking the time to comment 👍
@philmoody2445
4 жыл бұрын
BoilerDan1 need to add one more question: did you ever change the spring of the pull starter? Cause the second pull starter was stuck and I opened it and couldn’t close ist anymore....
@BoilerDan1
4 жыл бұрын
Phil Moody ; As far as the pull start cord, I was never able to figure out how to increase the tension once the cord has spun lose. The good news is that they were inexpensive to buy the pull cord unit. Coating the rope with bee wax really increased the wear and tear on mine as well.
@kenmoran4496
5 жыл бұрын
Thanks for all the work you put into these videos. They have been helpful. I just bought the same 3.6 HP from eBay and have been making all of the updates you have suggested. So far it feels like a pretty solid motor (for the price) once you take care of the known issues. I noticed on this video that you were able to give some throttle and have it stay at that speed without having to provide continual pressure (turn) to the throttle handle. On mine I can turn it freely, but when I let go it turns back to the idle position on its own. Did you do something to allow it to maintain throttle without keeping constant pressure on the handle? I did try tightening the little hex bolt on the end but it hasn’t worked so far. Thanks
@BoilerDan1
5 жыл бұрын
I don't recall adjusting anything? I the beginning I also had to hold it to go full throttle..... Maybe the handle extension that I put on had something to do with it. I ended up putting some small wooden slats inside the handle extension to allow it to grip better, I'm guessing that did it. I want to mention that during break-in I kept a close eye on water temperature in my bucket. You need to supply cool water so you don't over heat. I broke it in last winter and added snow or cold water to the bucket from time to time, but didn't show that on the video's. I'm enjoying the little motor and will get it out again in the spring. I'll try to document any problems that I have along the way and update with a video from time to time. Good luck with yours.
@kenmoran4496
5 жыл бұрын
Thanks for the reply, I’ll see if I can’t find a way to keep the throttle handle turned without holding it. Maybe it starts to “stick” a little after some use. I’ll keep an eye on the water temps in my bucket during break in.
@bentontool
11 ай бұрын
Outstanding videos! Thanks.
@BoilerDan1
11 ай бұрын
You’re welcome. For those that have the means and want to contribute to helping fund my adventures. A new $1 appreciation feature is available: Below and right of the videos. The “Thanks”” tab will show how. No need, just making it available.👍😂😂
@projectpatfilms8357
3 жыл бұрын
Excellent review brother! Extremely helpful. 👍
@BoilerDan1
3 жыл бұрын
You’re welcome. Thanks for watching and taking the time to comment 👍👍
@barriewatson
5 жыл бұрын
The old British seagull always had water in the gearbox you put in marine oil there were no seals but it was always ok
@BoilerDan1
5 жыл бұрын
Thanks, I will worry less about the issue. I figure I'll check it from time to time, and swap it out if looks like too much. Thanks for watching and taking the time to comment.
@kristindivino7479
4 жыл бұрын
this is my girlfriends KZitem account I am commenting from haha Man thanks for taking the time to make this video and share your knowledge it’s been very helpful.
@BoilerDan1
4 жыл бұрын
There are several video's that I've made on my motor. It's been quite the journey! All in all I'm happy with it, but there have been issues.... Keep watching! I've replaced the spark plug, fuel lines twice, and the clutch. The clutch replacement wasn't difficult and I used a lighter spring which has really helped. Check those out when you get a chance. Thanks for taking the time to comment. Hope she didn't mind!
@RedfishInc
6 жыл бұрын
You said you paid less than $200? That's amazing! That is about a quarter of the price of more mainstream brands of similar rated power. Very tempting to give it a try.
@BoilerDan1
6 жыл бұрын
The block of the motor seems very solid to me. Some of the exterior parts are questionable, but I've replaced some of those things. I've mentioned before that I do like the motor and it continues to run just fine. The price does seem to fluctuate, so if you keep your eye open, I bet you kind find a good deal too. I did buy mine between Christmas and New Years Day. Maybe it was a slow time? I've gotten more than $200 in fun with it for sure!
@salamalaykom7181
5 жыл бұрын
@@BoilerDan1 Yes l just order same one from ebay for 180$ . It was fantastic deal
The lower section looks everything like a Yamaha 2hp,does it not have fill screws for gear oil change /refill.
@BoilerDan1
3 жыл бұрын
No, they must have skipped copying that feature 😉 Thanks for watching 👍👍👀
@waynejestings8532
2 жыл бұрын
Thanks, WOW this saved MY ASS, I was told this is a plug and play ready to go just add fuel. I am happy I found this video. I am now going to get some SAE 90 , I will grab a cj8 as well.( just incase ) LOL Thanks again
@BoilerDan1
2 жыл бұрын
When I started my journey and decided to film it I had no idea of what I would run into! Nor how my efforts would help others like me! Just wanted to play around and not spend a lot of money! Although you’ll be doing some work on it, it’s pretty easy and I actually enjoyed it all! Thanks for watching 👍👍
@Voxguitarsrock
5 жыл бұрын
Good review and video thank You! Internally it reminds me of a weed eater at least a little bit.
@BoilerDan1
5 жыл бұрын
Yep, kind of sounds like one too :0)
@douglasadams953
5 жыл бұрын
I just bought one of these motors - my is called a Seahorse but basically the same motor - little different in cover design. Anyway thanks for your videos Boiler Dan you kept me from having to deal with a lot of repairs/modifications. I just got the gear oil, marine grease, new spark plug and will use bow string wax instead of the bees wax since I couldn't find it today. Thanks again and I'll let you know how well it works on my first outing this weekend after I get all the tips you provided done.
@BoilerDan1
5 жыл бұрын
Glad to hear my videos have helped! It will be better doing the break-in during the summer. On the gear oil... Don't over fill it. I discovered there is a line inside the casing. There is also markings on the outside that says fill to here.... very faint but it is there. And if you've watched all of them, you know not to overtighten those nuts! In the summer, you can take it out and just run it slow and medium until your tired of running. Keep track of the time run. The more I have run mine, the smoother it has gotten. Although I haven't even gotten out this summer at all.... The water is still too high for going out in a raft. A hard shell boat would be better. But I'll get out eventually! Thanks for taking the time to comment.
@raniasuesi9026
4 жыл бұрын
excellent review , Thank you sir
@BoilerDan1
3 жыл бұрын
My pleasure!
@sailingeden9866
3 жыл бұрын
So it does not have a transmission and the water pump is keyed to the prop drive shaft. So if the prop is not turning neither is the water pump. How long can it be ran in neutral without cooling water before the motor burns up?
@BoilerDan1
3 жыл бұрын
That I don’t know? The motors block has some cooling fins that might help some? But I’m guessing that you would want it to sit in idle for long periods of time. They offer a 4 cycle that is air cooled, and if I had it to do over again, I would probably get that model. The 2 cycle doesn’t have a muffler, it sends the exhaust out below the water line.... so the fish will definitely hear you coming! It’s basically to get you from point A to B. Not for trolling! Thanks for watching 👍
@unlimitedj06
2 жыл бұрын
Boiler Dan 1, can the tiller handle be reversed? I am trying to use it on a kayak and the motor would be in front of me, it will be facing forward.
@BoilerDan1
2 жыл бұрын
In looking at the handle, it does appear that you could simple un-bolt it from the motor and turn it around. The throttle cable may need disconnected and reconnected so that it doesn't have a twist in it. However, I'm not sure how well suited the motor will be on a lightweight kayak? Especially in the front? Although I think I recall the motor weighs less than 25 lbs. The thrust / pull of the propeller could become an issue? Also, the motor is a bit loud. There is no muffler, it just vents below the water line.... So not good for trolling. But from point A to point B it would do the job...... but I suggest you review all my videos, so you are aware of the issues I ran in to. It's not for everyone, but I enjoyed it. Unfortunately, after I turned 70 my family encouraged me to sell the entire raft and motor. In hindsight, I would have been better off with a lightweight solid fishing boat and trailer.... That being said, I was happy with almost everything except the softness of the raft created a loss of thrust because it would flex..... I ended up breaking even when I sold it.... So maybe if it doesn't work on you kayak, you could sell the motor! Thanks, and keep watching the series before deciding if it is right for you!
@jakers9932
11 ай бұрын
Thank you for this video! This helped me and dad out a lot. Do you know the best way to get a 35:1 mix? I was going to buy a small Jerry can and mix in that, to pour directly into the motor
@BoilerDan1
11 ай бұрын
I went to my local Walmart and they had one. Amazon has several, here’s a sample: Portable 2-Stroke Engine Oil Fuel Mixing Bottle Tank 20:1/25:1/40:1/50:1 Chainsaw Strimmer Chain Saw Brush Cutter Trimmer (1L) a.co/d/5TmtSC7 You might have to mark between the listed ones during break in…. But after that the 50:1 burns cleaner and is clearly marked. Search Amazon and you can probably find one with 36:1 marks. Thanks for watching 👍👍
@jamesstuart3346
2 жыл бұрын
Great review. Thanks!
@BoilerDan1
2 жыл бұрын
You’re welcome. I made several videos in my journey with the motor including some replacement of some maintenance items….clutch and pull cord. I’d suggest checking some of them out too. I’m not a mechanic and was able to stumble through them. But good to know if you’re considering buying one. Thanks for watching and taking the time to comment.👍👍
@raiderman7869
5 жыл бұрын
My state does have non ethanol gas so I have no choice but to purchase already mixed non ethanol 50:1 fuel on line. Can I still do the break in with that cause the next already mix available is a 20:1
@BoilerDan1
5 жыл бұрын
It's very important to use the higher amount of oil in the fuel during break-in. So don't use the 50:1 during break-in. Regarding the fuel, I discovered that I have been using ethanol gas all along. I get the highest grade fuel though. So I would recommend getting the most expensive gas at the pump, then break the motor in with the correct fuel / Oil mix and mix it yourself. So far the only problem I had which probably was due to ethanol in my gas too was one of the fuel lines rotted out. That's a cheap and easy replacement that you could even do right away. Or start out with the 20:1 mix. Just know that even the 35:1 mix (or was it 30:1?) will result in excess oil coming out the exhaust port. But once break in is done, the 50:1 mix will run clean. Have fun with the motor! Check out the other video's I've done, I will keep posting as things happen. So far nothing major, but making some easy changes that I have covered in the video's might help you along the way. Thanks for watching!
@aquelinalauzid
6 жыл бұрын
hi dan i just got this motor and im asking when greaking in motor do you use 50 to 1 ratio or the 35 to 1 ratio
@BoilerDan1
6 жыл бұрын
35 to 1 for the break-in period. That way your getting a little extra oil for better lubricating. It will result in a little oil residue, but that will go away once you are done with the break-in period. Remember to not go full speed during break-in, and vary your speeds over that time too.
@darylphipps2919
5 жыл бұрын
Guessing not much of an air filter as there may not be much dust out on the water? But looks good so fsr.
@MrGizmoto
3 жыл бұрын
I saw on some spec sheets #93 gas, do you use premium gas or is that a different number than octane?
@BoilerDan1
3 жыл бұрын
I always used premium hoping that would have less ethanol, however now most stores Hardware like Menards and even Walmart are selling non-ethanol fuel in the stores in the lawnmower areas. The ethanol deteriorates the fuel lines. But I think you can also get ethanol resistant fuel lines now!
@timkaczmarowski8151
Жыл бұрын
boiler up! hey how does the mix jug work? i just got one of these but the mix jug has no lines to show what level to fill the gas and oil to. I do have Chinese chainsaws and a Chinese leafblower that all came with multiple line mix jugs for different fuel ratios and I could use one of those as they all have a 35:1 option but figured I would use the one that came with the outboard as its the only 35:1 thing I have and I could keep it dedicated for the outboard.
@BoilerDan1
Жыл бұрын
Hammer Down (as they say😂👍). I’d use one of your old ones with the markings. The Hangkai web sight recommends the following: HANGKAI two-stroke outboards fuel used for lead-free number from 90 to 93 two-stroke gasoline and gas oil (TC-W3) mixed oil. The new machine in the running and fuel oil during the volume ratio of 25: 1 (ie, the oil content of 4% gasoline); After the run-in fuel and oil volume ratio of 50: 1 (ie, the oil content of 2% gasoline). Here’s a link to it: m.hang-kai.com/en/ I’m the upper left corner click on the 3 lines. Then click on “News”. You’ll find more information there. NOTE: 25:1 will leave an oil residue so I wouldn’t run that a long time. Then finish breaking in with 35:1. After that it’ll run clean on the 50:1 that they recommend. Back on the jug….. you could mark it yourself by first using your older one. Then pour into it the oil. Mark that. Then do same thing with the gas…. I bought a new one with markings on it 👍👍
@timkaczmarowski8151
Жыл бұрын
@@BoilerDan1 hey thanks for the quick reply, looks like i will use one of my old mix jugs since they dont even want you to use 35:1
@BoilerDan1
Жыл бұрын
You’re welcome….. I really don’t answer this quickly, you just happened to ask about the same time I check for activity.👍👍
@timkaczmarowski8151
Жыл бұрын
@@BoilerDan1 so i did the 10 hr break in with all 25:1 mix, and i hav oil in air filter and in other places, planning on a 50:1 mix now, guessing that will fix all that
@BoilerDan1
Жыл бұрын
Yes, the 50:1 will burn clean! Some people have suggested breaking in at 30:1 . Even that leaves oily residue. Thanks for watching 👍👍
@hankthedog2049
3 жыл бұрын
Thank you sir great video
@BoilerDan1
3 жыл бұрын
Thanks for watching 👍
@heritagelandscapedallas
2 жыл бұрын
trying to change the pull start rope. It's impossible to remove the broken off cord. Needle nose vice grip will not pull out. But the rope snapped off. Used the motor twice. Any advice Land locked in Texas.
@BoilerDan1
2 жыл бұрын
You’ll have to replace the pull start system. Easy and cheap 😁 Here’s a sample: www.ebay.com/itm/324402571624?mkcid=16&mkevt=1&mkrid=711-127632-2357-0&ssspo=u42jVzE4So-&sssrc=2349624&ssuid=s8A53jWuRTC&var=&widget_ver=artemis&media=COPY Here’s how to do it: kzitem.info/news/bejne/lXeanWSuqod_i2k
@BoilerDan1
2 жыл бұрын
Also, coat your new pull cord with bees wax. It’ll last a lot longer!👍
@BoilerDan1
2 жыл бұрын
Amazon has them too: Gekufa 33cc Recoil Pull Start Starter for Compatible with ATVs Pocket Dirt Bike 43cc 47cc 49cc 50cc Gas Scooters Pocket Bikes Mid-Bikes Mini-Choppers Small Quads with Claw Pawl Cog (Set of 2) www.amazon.com/dp/B08SJ2WLNL/ref=cm_sw_r_cp_api_i_R1E2275T5H4VNRBV0YQM
@audiotech1983
2 жыл бұрын
did it come with a title or a MCO manufacture certificate of origin? or MSO manufacture statement of origin? In texas we need it for titling purposes.
@BoilerDan1
2 жыл бұрын
Sorry in Indiana the boat itself is registered. In your case you’ll have to apply for a title to be assigned. Usually you get a form to take with you to law enforcement to inspect. Maybe similar to if you built your own trailer, the state assigned it to a unique number….. maybe not worth the hassle. Sorry.
@mikespinelli1024
3 жыл бұрын
I have an older model Hangkai (grey/diff location of choke lever). Maybe you can help with a few questions. 1. there is no fuel filter. should I add it? 2. I did not add gear oil or use the 32:1 break in mixture. Should do the break in mix now? I will add the gear oil. The instructions at the time were horrible.
@BoilerDan1
3 жыл бұрын
Fuel filter is inside the gas tank and yes I would add one. If you have already run the motor for several hours, then no reason to use the higher oil/fuel mix. But if only run a little, then yes do the higher amount of oil. You can use the motor during that time, just very your speed from time to time. I’ve heard that the older motor came with gear oil in it. But I would check it and change it out anyway. Hope that helps. Thanks for watching 👍
@mikespinelli1024
3 жыл бұрын
@@BoilerDan1 thanks dan ...i did find the fuel filter. there was no gear oil so I added. I have only run it an hour so I'll start the 30:1 mix now. Thanks!
@eamonnocarroll5866
Жыл бұрын
Excellent video
@BoilerDan1
Жыл бұрын
Thanks. It’s not for everyone but if you know what to expect it’ll help.
@nengthor1170
6 жыл бұрын
I bought this Hankai 3.5hp last year on Ebay but hard to use. It was hard to staring up. It took me a lot times to get starting but when I shut of the engine and try starting again it won't start. Had to try so many times when lucking it started but most the times it won't. I hate to use it. Any suggestion. I might throw in the trash. It was brand new motor. It cheap but it not good.
@BoilerDan1
6 жыл бұрын
Not sure how to help. If you did everything correctly.... 35:1 oil fuel mix. Make sure you turn the choke to "OFF" and then turn the throttle handle about 1/2 inch toward higher run. Mine starts every time on second or third pull of the starter cord. Also, did you put gear oil in the bottom, near the propeller? (watch my other video's to see what I am talking about). Good luck, hope this helped.
@HuberLawn
6 жыл бұрын
Neng Thor don't throw it away. If you are interested in selling it let me know.
@geog5523
5 жыл бұрын
Buy a used tohatsu or nissan 2.5 3.5 hp 2 stroke. Ive owned many some of which were blue and from the 80's that ran extremely well and reliably. Thats the best $200 solution to your problem
@mohamedmarzouk8759
Жыл бұрын
Hello Dan, when you do the break-in for the engine, do you remove the propeller?
@BoilerDan1
Жыл бұрын
The best way to break in motor is on your boat. Leave propeller on. I took mine off only because I do not live close to lake. You must keep cool water running in the barrel to keep motor cool if you can’t put the motor on your boat. Here’s the manufacturer’s website that may help too: m.hang-kai.com/en/nr.jsp
@mohamedmarzouk8759
Жыл бұрын
@@BoilerDan1 appreciate it mate
@atanacioluna292
4 жыл бұрын
Wonderful review. Thanks for all the detail. I want to buy a 6 hp 4 stroke. Your review indicates to me that the motors are good enough for the price, which is less than a third of a high brand motor. What's your feeling? Do you agree? It seems to be a bit on the loud side, which is a big deal to me. What do you think, compared to the more expensive brands?
@BoilerDan1
4 жыл бұрын
For some unknown reason, I'm not seeing my reply? I will summarize here: I'm happy with my motor, but there are issues I've had to overcome. They are a little things and are posted in the several video's I've made on the motor. But noise compared to an expensive outboard motor is an issue. It's not as loud as a weed-wacker, but it is louder than any regular outboard motor. However the 4 stroke does have a muffler, so it might be quieter than my 2 stroke. The 2 stroke exhaust is underwater to be specific, so your not going to sneak up on any fish that's for sure! Sorry for the delay, but I"m sure I had responded, it's just not showing up here for some reason? Thanks for watching.
@kk-ge9rn
2 жыл бұрын
Hi, do I put the pin back on it place after I filled the oil?
@BoilerDan1
2 жыл бұрын
Yes you can. But only if you are putting the propeller back on too. It’s best to run the motor on your boat. I only used the bucket because it was winter. I kept adding snow to keep the water cool. If yea use a bucket, you should keep water running into the bucket to keep water cool. But best to take out and run motor on your boat. Thanks for watching 👍
@StevenZhuang
Жыл бұрын
Did you hear a clatter sound when idle or low speed? I think something might be wrong with mine
@BoilerDan1
Жыл бұрын
Not that I remember? But the clutch system has moving parts that could make that kind of sound if your at a speed where it tries to engage and disengage…? The clutch system is not the best on these…. See my other videos on clutch and sprig issues.👍
@DPSlim
3 жыл бұрын
Sir: Thank you so much for the video! When my engine arrived, the instruction manual didn't even display the manufactures name? When in doubt, check KZitem, right? The instructions say absolutely nothing gear oil? fuel line checks? or even the gas mixture? I guess it was all lost in translation! lol
@BoilerDan1
3 жыл бұрын
Well, then it sounds like I was able to help! Enjoy your journey with it. Thanks for watching and taking the time to comment! 👍👍
@stevenbaker2246
5 жыл бұрын
Thank you!!!!
@generalworks47
5 жыл бұрын
good video thanks, i doubt i will buy any of those cheap looking motors.
@BoilerDan1
5 жыл бұрын
Thanks for watching. I'm satisfied if my work helps anyone decide one way or the other.
@livingthedream4882
3 жыл бұрын
Hey dan ..do u know the 3 little spare propeller pins they give u how offen do they snap ?
@BoilerDan1
3 жыл бұрын
Mine never has snapped and I actually ran up on a shallow spot bumping along on a rocky bottom (small quarter size rocks and sand). But I did lose one out in my lawn when I had removed the propeller but forgot to remove the pin.... it was somewhere in the grass but I couldn’t find it.... I carried a spare in my tackle box too. I made extra using a brass rod. I think that’s what they are made of, apparently brass will snap under pressure. The diameter was slightly smaller but it works! I don’t remember getting 3 with mine? I bet they are hiding in my garage somewhere? I’ll have to do a deep dig to find them! 😂 You: Keep living the dream! My location was 28 degrees overnight (-2 Celsius) 🥶
@livingthedream4882
3 жыл бұрын
@@BoilerDan1 ok mate thanks once again 👍
@robertclark1868
6 жыл бұрын
Are you using marine grade 2 cycle oil or just regular 2 cycle oil?
By far one of the best review/demos I’ve watched on any product. It’s appreciated by many. Have you had the opportunity to try it under a load yet? Would you purchase again?
@BoilerDan1
6 жыл бұрын
Thanks! I have not had a chance to try it out on the water yet. I will test it out as soon as the water levels here go down. Near record floods on the Tippecanoe river where I'd like to run my test. Hopefully early April 2018. I also discovered that in Indiana you must register and title a raft if putting any motor on it. I completed that this morning. (I may make a video on that process as you have to get special forms from the seller.) I will continue making video's with any little snags that occur as I use it. I would definitely buy it again. Mid-winter it was just under $200. It will probably go up a little due to seasonal demands. But for my use, spending upwards of $1,000 wasn't going to happen..
@finneganmario7705
2 жыл бұрын
i guess Im asking the wrong place but does any of you know of a way to log back into an instagram account? I was stupid lost the password. I appreciate any assistance you can give me.
@adrianjaxton6584
2 жыл бұрын
@Finnegan Mario instablaster :)
@finneganmario7705
2 жыл бұрын
@Adrian Jaxton Thanks so much for your reply. I got to the site through google and im trying it out atm. Takes a while so I will reply here later with my results.
@finneganmario7705
2 жыл бұрын
@Adrian Jaxton it did the trick and I actually got access to my account again. I am so happy! Thank you so much, you saved my ass :D
@randylenart9674
2 жыл бұрын
Older boat motor's didn't have air cleaner's looks like cheep fun 👍
@BoilerDan1
2 жыл бұрын
I did have a lot of fun with it! Thanks for watching 👍
@steinaresolstrand5134
3 жыл бұрын
Hei. I have just purchased the Hangkai 3,5 HP and I have a question for you. What is the basic procedure to activate the propellar when it has started? There is no "gear handle" to activate the propellar, so is it something that you do on the trottle?
@BoilerDan1
3 жыл бұрын
Yes, it’s by giving more power from the throttle. It has a centrifugal force type clutch that expands and causes the propeller to spin. In one of my later videos I show the clutch system too. In my opinion, the clutch spring is too strong and will cause the clutch to wear out sooner than it should. It’s a relatively easy replacement. I suggest that you watch the clutch replacement videos as eventually you’ll need to do that. Thanks for watching!
@steinaresolstrand5134
3 жыл бұрын
@@BoilerDan1 OK. Thank you so much for answering :-)
@BoilerDan1
3 жыл бұрын
Happy to help! Thank you for watching 😁
@mrg7143
2 жыл бұрын
Would you consider it a louder than an average 3.5hp 2 stroke outboard?
@BoilerDan1
2 жыл бұрын
Yes! Well I’m not familiar with other two stroke outbreaks, but if I had it to do over, I’d reconsider getting the 4 stroke because it has a muffler. But this one is the same as all the other inexpensive 2 strokes out there. Thanks for watching 👍
@marcloranger1762
Жыл бұрын
Hi Dan , I realized you said a Champion cj8 ace didnt have one they suggested a cj7 and after changing the plug and adding new fuel it doesnt start at all? COULD IT BE THE PLUG??
@BoilerDan1
Жыл бұрын
Yes! I’d suggest NKG plug. Here’s a video on it. I list the number with the first 30 seconds of the video. I’m not home or I’d look it up and list it here. But I’m guessing using the cj7 isn’t gapped right? Watch this one: kzitem.info/news/bejne/q4uXrp6tg4WYn6w
@BoilerDan1
Жыл бұрын
You can probably get plug from Amazon.
@marcloranger1762
Жыл бұрын
@@BoilerDan1 Thanks Dan I did get it going and will try it out on the river Monday ,Thanks again
@BoilerDan1
Жыл бұрын
Great! You’ll figure out it’s little glitches with experience 👍👍
@tammyboyd7221
6 жыл бұрын
First off I want to say thank you for your detailed videos on this Hangkai motor. My fist experience with this was last summer when I purchased a used 12f Pelican jon boat that came with a 2 stroke 3.5hp motor. Of course it only worked once but I don't think it was properly taken care of in the first place. I have watched many vidoes about this motor some good some not so good. Being that all the good American outboards are far outside my price range I bought a brand new Hangkai 4 Stroke 4hp. I have followed all your videos and they are great. But we all know the instructions are terrible. I was wondering about how much oil it takes on initial fill up. The dipstick must have been made by a dipstick. Lol. It is very confusing on the marks and the picture in the instructions makes it look like you should fill it to the point you can look down the fill hole and actually see the oil. I would appreciate any input on this. Thank you.
@BoilerDan1
6 жыл бұрын
I purchased the 2 cycle version (mix of oil & gas). I choose it due to the fact that I have to lay the motor down in the back of a Subaru Forester. I read that the 4 cycle because it holds the oil can also leak out if you lay it on the wrong side...? But to answer your question the best I can... It sounds like a similar system to some lawnmowers. You fill until it almost runs out but not quite.... With the 4 cycle, it's more like a car, you have oil in a reservoir that gets splashed or circulated on the engine parts and you will change it from time to time. The 2 cycle you add it to the gas and it burns up with no bulk amount of oil in the engine. For sure still do a gentle break in, as well as add good gear oil....I'm sure it came with none too. I'm in the process of making my final "On the water" test video. I'll post it when complete. Then I will add more if and when I have any complications. Thanks for your encouragement. Wish I could provide specifics on your 4 cycle motor.
@BoilerDan1
6 жыл бұрын
Here is something else I found. It's helpful hints from the manufacturer. Some how to kind of things. www.hang-kai.com/en/nr.jsp But I didn't find anything on oil capacity...sorry.
@tammyboyd7221
6 жыл бұрын
Thank you for your reply I realize I was looking at the wrong videos when I asked my question. sorry about that. I just started my motor and it started right up and sounds great but I noticed that even when idle is turned up there is not water coming out the water exhaust port ( or whatever it is called) that is half way up the shaft. Just wondering if yours is that way? I already took the cover off to make sure there is no blockage and there is nothing.
@BoilerDan1
6 жыл бұрын
I think you stated that you purchased the 4 cycle motor. From what I have seen on line, it is air cooled instead of water cooled. So you won't have water coming out. Here is a link of what I think you ordered and this one is air cooled. www.ebay.com/itm/2-4-Stroke-Outboard-Motor-Fishing-Boat-Motor-Engine-7HP-6-5-6HP-4HP-3-6-3-5HP/332632568029?_trkparms=aid%3D555018%26algo%3DPL.SIM%26ao%3D2%26asc%3D50544%26meid%3D4972393d25644486946bd62579ac2faa%26pid%3D100005%26rk%3D4%26rkt%3D12%26sd%3D282595525253%26itm%3D332632568029&_trksid=p2047675.c100005.m1851 HOWEVER if your model is watert cooled, water will only come out when you speed the motor up above idle. It has a clutch that allows the motor to idle without the propeller moving. So if you speed the motor up so that the propeller is turning, then water will come out if - it is fact a water cooled type. You can also see the water tubes when you remove the engine cover. On mine they are black plastic with one inlet going in on one side of the piston area and the outlet on the exhaust pipe side. At the 14:52 time mark of this video link you can see the two clips and tubes on the sides of the motor. They are the water cooling tubes. Here is the video that shows it> again fast forward to the 14:52 time mark. kzitem.info/news/bejne/lGhop6VtbGdybJg
@tammyboyd7221
6 жыл бұрын
It is in fact air cooled. I did wonder if that was the case and now it makes complete sense. I greatly appreciate your help and look forward to watching more of your vides. Thank you very much for your time.
@nicholasdupuis5721
3 жыл бұрын
Hey boiler Dan thanks for your videos they've been a help ps I'm a subscriber but i got a question though. I got mine running in a bucket but it's not putting any water through the cooling system I don't know how long it's supposed to take it for that to happen cuz I don't want my motor to get too hot. It's running for like 5 minutes and didn't do anything figured it would have started cycling water through.
@BoilerDan1
3 жыл бұрын
Very important: keep cool water running in the bucket! I kept dumping in snow! Better yet, break it in on your boat in the water. You must rev the motor enough for the clutch to engage. That may require almost full throttle! The throttle works on centrifugal force. If no water is coming out, you’re not cooling the motor. The clutch spring in these is too strong. I replaced mine and that helped a lot. You could even remove the spring during break in.... but realize that the propeller will always turn, so I wouldn’t do that all the time. Here’s a link to the video that mentions the spring. I ended up using the one from Menards, not the one I mention from Home Depot. kzitem.info/news/bejne/qGqnsqtnbZ6XbKA Regarding clutch replacement see the below two videos: kzitem.info/news/bejne/qWqjtnurfn2ffn4 kzitem.info/news/bejne/sqtvtZ6Om3-mp3Y And after the spring replacement kzitem.info/news/bejne/rZqqr4h8sWh_YIY Let me know if that’s not clear and I’ll try to help.... But know that if the propeller isn’t turning and no water is coming out, you’re not cooling the motor.
@nicholasdupuis5721
3 жыл бұрын
@@BoilerDan1 I see what you mean I ran it almost full throttle and it was spitting water out like it should. I might replace the spring like you mentioned I'll have to check your videos out on that. Seriously man thanks a lot I appreciate it.
@BoilerDan1
3 жыл бұрын
@@nicholasdupuis5721 It almost has idle and full speed and that’s it 😂. Seriously though, you need to run it fast enough to get the water spitting out. Just keep changing the speed. Even if you slow to an idle for 1 minute, then speed it back up enough to keep that clutch engaged! I think you’re understanding now... it does have to go fast as part of the break in process. Thanks for watching 👍👍
@nicholasdupuis5721
3 жыл бұрын
@@BoilerDan1 I noticed that too lol. I think I am understanding it again I really appreciate it. I'll keep watching if you keep posting thanks again.
@beverlynguyen5220
4 жыл бұрын
I have a question, so does this run off oil and gas mixture?
@BoilerDan1
4 жыл бұрын
Yes it does require mixing the oil and fuel together. They do make one that they are separate too. I went with the one I bought because I needed to lay it sideways to transport it. That can be a problem for the one with the oil separate as it can drain back into the cylinder fouling out the spark plug. Thanks for watching 👍👍
@kyredneckoutdoors
4 жыл бұрын
i think ill have to check and see if i can find fuel line and a primer bubble that will handle ethinal because thats all we have in my area. i just bought one of these and will be beginning the break in next week
@BoilerDan1
4 жыл бұрын
Hope my videos help! One important thing, I have been told that in breaking in the motor, to leave the propeller on. Also if using a bucket, keep running cool water constantly. I’m also trying to find better fuel lines. I’m going to check at a local lawnmower repair shop. Thanks for watching!
@BoilerDan1
4 жыл бұрын
I use the highest grade of fuel and have found an additive that says it will counter the effects of ethanol. I purchased the additive at Wal-Mart. Can should prepare yourself to replace the clutch..... I've posted a video on that too 😅
@TylerLL2112
5 жыл бұрын
I’m trying to decide to go with this or an old faithful Johnson or Evinrude from late 50s-70s. I’ll probably give one of these a shot and if it fails me, I’ll go with an old battle axe Johnson or Evinrude.
@BoilerDan1
5 жыл бұрын
Just make sure you check out my other videos. I've done a lot of tweaking, and recently replaced the clutch as well. I think if you are handy and don't mind working on the motor, it can serve you well. But there are issues. (spark plug, fuel lines, gas cap vent, clutch, lose wire on cutout switch... So check out my other videos so you know what to expect. All in all it runs well, but it's not without issues... Power, noise...… But I do still like mine. Thanks for watching.
@TylerLL2112
5 жыл бұрын
BoilerDan1 Alright. I’m extremely handy. The way I see it, if I buy an old motor I’m going to have to tear into it unless someone else got it running and it’s cost will likely reflect that. I think I’m going to buy one of these an an old Evinrude as a project to fix as a more permanent solution. But, we shall see I have a little while to think on it. Thanks for your reply. I will check out your other videos. I subscribed also. Take care!
@BoilerDan1
5 жыл бұрын
Keep you eye open for a good deal! Especially if you are in no rush. The prices on eBay fluctuate. I paid $181.00 in late December. Just to give you an idea. Have fun!
@nicholashamelink6197
Жыл бұрын
Hi! I just bought one on Amazon for $160. I'm going to put it on and old 12' starcraft jon boat. Your videos have been super helpful. I'm breaking it in now by running it 1hr a day in the tank with 35:1. I was wondering what your thoughts were on running 40:1 after that. Do you think running the extra oil might prolong the lif of the mototr?
@BoilerDan1
Жыл бұрын
Actually after break in the manufacturer’s website advises to reduce to 50:1. I’d go with that as it motor will run cleaner and better. Use the best quality oil and that’s the best way to improve longevity. Here’s a copy of Hangkai website: HANGKAI two-stroke outboards fuel used for lead-free number from 90 to 93 two-stroke gasoline and gas oil (TC-W3) mixed oil. The new machine in the running and fuel oil during the volume ratio of 25: 1 (ie, the oil content of 4% gasoline); After the run-in fuel and oil volume ratio of 50: 1 (ie, the oil content of 2% gasoline) Here’s the website: m.hang-kai.com/en/ Go to the horizontal lines at the top left corner. Click on them then click on “News” and you’ll find some helpful information.
@BoilerDan1
10 ай бұрын
@HI-PSI Due to age (71), and not having a lake nearby….. taking it out on the river on an inexpensive raft….. Sometimes you just need to take into account your limitations….. short answer, no…. I sold it to a younger guy that had previously owned another similar motor and was thrilled to get it. If I’d had it on a traditional hard body boat, I’d probably still be going out with it… Thanks for watching my adventures!😂👍
@jaredpeterson380
Жыл бұрын
TMike down in Cajun country says the problem with ethanol fuel, is the corn residue left in the carb and fuel lines. It will clog things up if the fuel sits in the float too long. I'd never heard that theory before.
@BoilerDan1
Жыл бұрын
You probably know better than me! I’d just heard that. But my fuel line did just snap off one day….. so I decided to just change them out on a regular basis. Not difficult or expensive. Thanks for watching and joining in on the conversation.👍👍
@jaredpeterson380
Жыл бұрын
@BoilerDan1 I've always heard that the ethanol could harm the rubber hoses. To be brutally honest, I don't know jack about any of this stuff. I just enjoy people fixing things, bringing old motors back to life.
@MrJames6674
5 жыл бұрын
remember that the base oil is 90 weight and the top number is just when its cold so REALLY your fine !!!!
@BoilerDan1
5 жыл бұрын
I hadn't thought about hear lube being the same as conventional oil on the numbers. Thanks for the info!
@xaviercanal1
2 жыл бұрын
Thanks Dan pretty good review. I bought one also ;)
@BoilerDan1
2 жыл бұрын
I made several videos of my experience with the motor. Including some repairs and things I had to replace as time went on. I’d encourage you to keep watching as some may be helpful. Also it’s best to break in the motor by using it on the water. I only used bucket because it was winter…. Kept adding snow to keep water cool. You should run hose in bucket to keep water cool. But best is just run on your boat. Thanks for watching and have some fun with yours too! 👍
@xaviercanal1
2 жыл бұрын
@@BoilerDan1 so many thanks for these advices and tips 👍
@BoilerDan1
2 жыл бұрын
It’s my retirement activity! 😂😉
@techguy3424
6 жыл бұрын
I wonder if a predator could be bolted to the lower half without a lot of modifying.
@BoilerDan1
6 жыл бұрын
Enlighten me? What is a predator? I hadn't fished or boated since I was in High School. I'm just winging it with this project.... But I will add that the motor gets better the more I run it! :0)
@RedfishInc
6 жыл бұрын
@@BoilerDan1 it's a brand of Chinese 4 stroke engine carried at harbor freight.
@BoilerDan1
6 жыл бұрын
I wondered what that was? I'm not that much of a mechanic to know the answer to that idea...
@geog5523
5 жыл бұрын
Look at the air cooled Honda 2.3hp or Briggs and Stratton , there are many similar setups on ebay and other manufacturers like Mud Buddy etc. It's been done and they suck too.
@ramabamaboomboom
3 жыл бұрын
Great job
@BoilerDan1
3 жыл бұрын
Thanks for watching 👍👍
@leslietorres7260
6 жыл бұрын
Can you use ethanol fuel if you replace the fuel lines with better ones?
@BoilerDan1
6 жыл бұрын
an ethanol blend - Yes I would think if you replace the lines with better ones it would be fine. I also had someone tell me the lines will go bad regardless. So I will keep an eye on mine for the first season.
@tomkiker2206
6 жыл бұрын
Any gas with ethanol well eventually gum up the jets in the carburetor. Always use non-Ethanol gas on any engine with a carburetor especially a 2 stroke
@BoilerDan1
6 жыл бұрын
Let me update: Tom (see below) is probably totally correct, don't use any ethanol. But if you are in a state that only offers ethanol blended fuels you might try this: I found that there are products that help with ethanol problems. I've cut and pasted info. (can get at Amazon, Walmart...Other places too. Lucas Safeguard™ Ethanol Fuel Conditioner with Stabilizers was developed to specifically address issues associated with using ethanol based fuels. This applies to E-10, E-15, E-85, pure ethanol and any mixtures in between including gasoline. Our Product is completely soluble in all ethanol fuels and will not harm filters. Lucas Safeguard™ Ethanol Fuel Conditioner with Stabilizers contains effective additives to prevent rust and corrosion associated with the use of ethanol fuels. Key Benefits Recommended for use in automobile and marine applications. Cleans injectors, valve seats, combustion chambers and other critical fuel components Stabilizes fuel and prevents varnish & gum formation in ethanol and gasoline Combats deposits and protects your engine oil lubricants from the harmful effects of alcohol combustion NOT RECOMMENDED FOR DIESEL APPLICATIONS One ounce treats five gallons of ethanol fuel. Our new 5.25 oz bottle treats up to 25 gallons (94.6 liters) of ethanol fuel.
@狮子子
5 жыл бұрын
Hi, does it tell u how important the paddle is?
@BoilerDan1
5 жыл бұрын
I wouldn't leave shore without them! :0)
@BoilerDan1
4 жыл бұрын
Thanks! I’m actually considering getting the 4 stroke so I don’t have to mix oil and gas, but that’s about 6 months away from consideration. If you’re concerned with it being noisy then you might reconsider. I don’t know about the 4 strokes but mine is kinda noisy compared to other boat motors. But not as loud as a weed walker or lawn mower. Make sure you check out what repairs I’ve made too.
@brentneves3602
4 жыл бұрын
Hey Dan, if you ever consider purchasing a 4 stroke out board, I have found that the Parsun brand 2.6hp or even the 5hp to be a great, extremely reliable engine. Parsun is a subsidiary of Yamaha, and their outboards are ISO rated, and we'll engineered.
@kernfed
2 жыл бұрын
hubby did what you posted, your a lifesaver!!! lol
@BoilerDan1
2 жыл бұрын
Tell him to still take a couple of paddles along…. Just in case! 🤣. Thanks for letting me know 👍👍
@stanleybest8833
11 ай бұрын
The four stroke is much simpler, air cooled, and has a beautiful quiet idle. 2 cycle? A speed demon.
@BoilerDan1
11 ай бұрын
In hindsight, the 4 stroke would have been a better choice overall. I chose 2 stroke so I could lay it sideways to transport….. Thanks for watching and commenting
@hawgstalkaztv5985
5 жыл бұрын
How much faster between the motor and a 45lb thrust trolling motor , I don’t go far but need more speed
@BoilerDan1
5 жыл бұрын
Sorry I can't specifically answer your question. I've never used a battery powered trolling motor. I can tell you that I chose to go with this little gas powered motor to eliminate the battery lugging around and the possibility of running out of power. That being said, if you watch a few more of my video's you can see me going up stream. The river (Wabash) has a pretty swift current. More than I ever realized growing up in the area. Going upstream, by looking at the shore line, it's a little faster than walking, but definitely not even a slow jog. Going downstream however, I'd estimate about 7 mph. I hope that helps you some. A part of me thinks the 4 cycle (4 stroke) would be a better choice? I had some left over fuel from last season.... Finally decided to try burning it off in a all metal Tiki torch. That worked, but I don't recommend that... Just saying what I did. With the 4 cycle, any left over could be put in a vehicle.
@BoilerDan1
5 жыл бұрын
One other thing to add to my first reply.... If you have a more solid boat, that is still light weight, I think you will do better going upstream. I have mine on a spongy air filled raft and I'm sure I lose some thrust do to that.
@clay6637
5 жыл бұрын
Dan the Champion plug is about as good as the one that failed so put an NGK in , Way better than rowing and most of these Chinese engines have cast iron piston rings so have a long break in period so plenty of short trips with a cool down in between as well.
@BoilerDan1
5 жыл бұрын
I have replaced the plug with the NGK as suggested. Thanks!
@williamsteele1407
5 жыл бұрын
What’s the black star thing that’s not in the motor
@BoilerDan1
5 жыл бұрын
Took me a minute to figure out what you were referring too? But I do have the answer. It is an extra water wheel used in the water cooling system. With the motor you get an extra one of those plus an extra pull start cord/spring assembly. Sorry I didn't point that part out in the video. Thanks for watching and asking.
@raiderman7869
5 жыл бұрын
Which 2 cycle mix brand do you recommend ?
@BoilerDan1
5 жыл бұрын
So far, I just picked up what was available on the shelf at a local Walmart. It is Quick Silver Marine Lubricants: 2-Stroke Synthetic Blend. Also important is adding gear oil at the bottom of the shaft at the propeller. I ordered Mercury High Performance Gear Lube SAE90 from Amazon. But next time I think I'll get the full synthetic at the store that has a range of SAE applications.
@drdraws9597
5 жыл бұрын
Looks like the water cooling is only for the exhaust?
@BoilerDan1
5 жыл бұрын
Not sure what you mean? But the water cooling lines do flow into and out of the engine block, so it does something to cool the motor.
@libinqw
6 жыл бұрын
Why on my manual it says 30:1 mixture ratio under normal usage?
@BoilerDan1
6 жыл бұрын
I looked back over what I received with my motor. Your correct the manual does say 30:1 mix during break in. HOWEVER, I received an email from the seller that there was a printing error in the manual and that the break in gas to oil mixture should have read 35:1. The email also says that after the run-in period the mixture should be 50:1. SO TODAY I LOOKED AT THE HANGKAI MANUFACTURERS WEB SITE: HERE ARE TWO LINKS: 1. This page lists the manufactures recommendation (25:1 break in / then 50:1 after break in). I'd go with 30 or 35, 25 will make an oily mess I'd guess. Once you go to 50 to 1 it runs very clean. I probably really am running closer to 45:1 just to be safe. HERE'S THE LINK: www.hang-kai.com/en/nd.jsp?id=2&groupId=-1 2. This is the LINK TO home page for Hangkai. www.hang-kai.com/en/ To find out information, click on the "Article" section that is at the top of the page in the black band. Then scroll down to find other information on the motor. If you haven't already, please subscribe to my channel. That will reward me for my research on this topic (0:
@libinqw
6 жыл бұрын
Thanks for the info Dan. Yeah I think the manual is probably wrong, I will stick to 25:1 and then 50:1. BTW, I saw in your another video you mounted the motor to a horizontal plastic board kind of thing, did that board come with the motor? I don't see it in my package.
@BoilerDan1
6 жыл бұрын
That was actually an optional item specifically for the Intex inflatable raft. So if you are mounting it on an Intex raft, here is a link to Amazon where you can get one. www.amazon.com/gp/offer-listing/B000NNM4BW Out of stock now but will be available early September. When I looked it was less than $18.00. That's less than I paid! Or search for: Intex Motor Mount Kit inflatable Boats. I'm posting a new video tonight and another in the coming days on a motor preventive maintenance topic.... Stay tuned!
@libinqw
5 жыл бұрын
I C, Thanks Dan, I went to the manufacturer website again, they have some tech videos and docs(I do read chinese), one of the video says 30:1 and the doc says 25:1: hang-kai.com/cn/nd.jsp?id=4#_jcp=1 LOL, I guess probably it is not that strict, as long as it's between 25:1 and 35:1 you are gonna be ok.
Пікірлер: 624