Upper oring: 8mm ID, 13mm OD, 2.5mm W lower oring: 10mm ID, 14mm OD, 2mm W
@draven4101
Жыл бұрын
Hey brother, thanks for the part numbers. This seems to be a common problem and you saved me the leg work of looking everything up. Ordering everything as we speak. Again bro, I appreciate the vid.
@garageonomics9411
Жыл бұрын
Ride safe.
@timothyupleger7007
3 жыл бұрын
Thank you for the tip on using an oil/transmission/primary drain plug o-ring on the fuel quick disconnect. It worked great.
@woodmister
Жыл бұрын
Saved me a hell of a lot of time. I'm ordering as I comment. Thank you for your help👍🏻
@mikebrown1972
3 жыл бұрын
Thanks for your video, I believe its just what I needed to see. I knew it was risky buying a 10 year old bike with 474 miles (2010 Street Bob), one owner and as soon as I touched the fuel check valve, it started leaking. I can see clearly the one on the fuel line is dry rotted, I'll start there. If I have to replace the check valve, lower, I know what to buy for that too now! Thanks for the video and ALL the time you saved me finding the right part! Sincerely!
@GoExpicitYourself4482
Жыл бұрын
Nice video exactly what I needed to know. Mine just started leaking yesterday. Thank you very much.
@garageonomics9411
Жыл бұрын
Glad it helped.
@commonsensepatriot9450
3 жыл бұрын
Thanks for the video! The drain plug o ring fit and fixed the issue. Not surprised Harley won't tell you this or sell the o ring to fix the problem.
@garageonomics9411
3 жыл бұрын
It is insane that something this simple is a mystery to them. They probably would not make a big enough profit from just an o ring. Haha
@boogerjoe1
9 ай бұрын
High five, looks like some others have used the drain plug rings with success, saves me any further delay since i have a sack lmao. Great info, thx
@boogerjoe1
8 ай бұрын
Oil plug oring didn't work, it's a bit too big in diameter, had to get the corrects oring and it worked
@rrmorris67
Жыл бұрын
I have a 2005 Road King and I have researched this leaky check valve problem quite extensively, as it happened to me a couple years ago. Back then I too was appalled at the prices so sought out a more reasonable solution. I ended up doing the same thing, and bought those same Fuel tool o rings to very carefully replace the lower o ring (there is an upper one in there, too). Good luck trying to rebuild the whole thing without the Fuel Tool tool, which costs $100! Anyway, here I am 2 years on and it is leaking again. Not regularly, and not much. It is very slight. But it is leaking and it will no doubt just get worse with time. I have a big trip coming up so I am fixing this once and for all. Turns out you can replace the whole check valve AND the inside the tank pex fuel hose connected to it for only about $30, including shipping. Its a Drag specialties part on Revzilla. In my research I have learned that the 2 pex lines inside the tank, as well as the Fuel pressure regulator housing, can get brittle (ethanol fuel effects on plastics and rubber) and fail and cause lots of problems and even leave you hopelessly stranded. So that's it. Im taking the whole unit out and I am replacing everything inside the tank (except the fuel pump) up to and including the leaky check valve. SO, two hoses, the regulator, housing, check valve and fuel filter. Also replacing the gasket and special screws that seal and hold the top plate down. I Already bought the parts. If you have an older fuel injected Harley and havent thought about whats inside that tank you may wanna get in there and replace that stuff as preventative maintenance.
@hossfly2832
3 ай бұрын
So the answer is to empty the tank?
@ianosborne188
3 жыл бұрын
Ive had a Springer for 30years..NO O Rings Problems There.. What the F is Up with this System!!!? 2015 Harley.. ⛽Leaks fuel on Hot Cylinders 🔥🔥🔥WTF!
@luisangelpandemonium
2 жыл бұрын
Thanks for the tips...
@chrisgotthat2435
3 жыл бұрын
I jumped the gun and ripped out the small o ring from the fuel line attachment first. When I noticed the leak, I popped the fitting off, it was in bad shape. I replaced it, thought I was good to go and still have a leak. Now I need to deal with quick connect o ring.
@goodboyringo9716
3 жыл бұрын
More Harley junk ! If Harley can't provide a better system , just give me a hose and clamp , like the old days. I'll try the small o-ring first but I removed the check valve from the tank but it looks good . Blew in the check valve hose and it holds air then I pushed in on the valve and air escaped so it seems good . My Road King has two check valves at the bottom of the tank . One is high pressure ( check valve near outside of tank ) and one a return. The return hose is smaller than the pressure hose. If you buy the short hose it won't work for the pressure ( to short) so knowing that will save you money. The pressure hose with check valve is 22" long, return is shorter.
@johnjohnson2855
Жыл бұрын
I totally agree a hose and a clamp never failed me yet!!!
@chrisgotthat2435
3 жыл бұрын
I got my gas to stop leaking with a new o ring i can heat my fuel pump when my harley is on, like the same sound as when the pump primes before turning it on. Is that normal? The motor and bike sound fine, no sputtering or anything like that.
@user-vk7jl9sz3h
4 жыл бұрын
Hello from Russia, guys. Could u please specify if it is quiet manageable to change the o rings by myself? Should the new ones be special, or random no-name o ring will do?
@lyndonwilliamson3781
2 жыл бұрын
Hi Great video and description and I have the same problem with my Harley,,,,how does you get the O ring out of the quick release unit on the tank,,,,I have changed the small O ring on the fuel line but still it’s leaking
@garageonomics9411
2 жыл бұрын
I used an o-ring tool, or pic and a mirror to see up into the fitting. It takes a little patience for sure
@ianosborne188
3 жыл бұрын
Is That Rain☔⛈️ Or Fuel Taps Leaking!!!!
@steventwiddy3402
3 жыл бұрын
I want to see you replacing the O ring in the check valve without the tool
@brianholmers9632
3 жыл бұрын
got it in there with a screw driver and used a socket to push it up.. once it was in the recess groove.. I used a smaller socket that fit inside oring to seat it in the groove nice and tight.. the hardest part was getting all the old oring out.. whole job took 5 minutes
@phabloagr
3 жыл бұрын
Would have been nicer if you had shown how to do it man haha 😅
@garageonomics9411
3 жыл бұрын
It was meant more to explain that there are o rings out there that work and you don’t have to buy the entire part from Harley.
@RodrigoMartinez-rl9pq
4 жыл бұрын
Do you have the sizes of each of the 3 o-rings you changed? I am from Argentina and is difficult to get that on Harley shop. Need to go to another place to buy them. Thanks!
@garageonomics9411
4 жыл бұрын
Fuel-tool part numbers MC300 and MC600-5.
@Budboy7
4 жыл бұрын
How do you get the quick release back in. I took it off to get under the tank now I can't get the thing back in there. Do you have to pull down and push the valve up it it or just push it up??
@garageonomics9411
4 жыл бұрын
Yes, you pull back push the connector in and then release. If that is not working and fairly easy then something may be out of place.
@coloradogrownHD
2 жыл бұрын
Did you have to drain the fuel out of tank to take that hose off??
@whatsinthembags
2 жыл бұрын
no
@LovelySinghGujjar
4 жыл бұрын
Please tell me how you managed to change upper o ring ?
@garageonomics9411
4 жыл бұрын
Patience. Ha. You need an o ring pick, a small mirror, and a light helps. The mirror helps you to locate the o ring. Once you find the groove with the pick it comes out fairly easy. Make sure to put a bit of lube on the new one.
@rustyjohnston3180
4 жыл бұрын
How about a video of how to change the damn O ring? (That's what I thought I was going to be watching)
@garageonomics9411
4 жыл бұрын
In all fairness the title does not say “how to change”. My frustration was with Harley not supplying the o ring so I was showing options. I did explain above in comments how to go about changing.
@glend4704
2 жыл бұрын
@@rustyjohnston3180 exactly!!! The video shows parts only. Not how to do it. That’s about useless !!
@fulviocervai7390
2 жыл бұрын
Ciao volevo chiederti se devo svuotare il serbatoio per sostituire le oring? Grazie mille Fulvio
@johnjohnson2855
Жыл бұрын
Yes
@martinnajera417
3 жыл бұрын
I hope this is not a dumb question just learning as I go but do you have to empty the gas on the gas tank to do this?
@robertmccully9017
3 жыл бұрын
No you do not.
@martinnajera417
3 жыл бұрын
Robert Mccully thanks man I appreciate it.
@BustedKnuckleCattle
Жыл бұрын
@@martinnajera417 lol i was looking through the comments just for this question, i was just about to ask the same thing bout to do mine.
@Nationalpdinc
11 ай бұрын
The Harley Davidson store sold me both hoses for $400 Dollars .😢
@jeffgalford3863
3 жыл бұрын
Did you drain gas??
@garageonomics9411
3 жыл бұрын
No I did not. It is a quick connect fitting so very little has should come out. You will get a little bit when connecting/disconnecting.
@metallica85rules
4 жыл бұрын
Can you post sizes or part numbers?
@garageonomics9411
4 жыл бұрын
Fuel-tool part#s MC300 and MC600-5
@dougbourdo2589
3 жыл бұрын
Good Grief. Don't people watch the video?? It is shown at least a dozen times.
@timgonzales9671
2 жыл бұрын
I went to my dealer and they gave me a o-ring
@MrRpibiz
4 жыл бұрын
u dint show anything
@Jennifer-bg1ih
4 ай бұрын
The quick connect is $70
@crystalmayer7909
4 жыл бұрын
Need to be Vinson o rings not water ones. Those will get eat up quickly.
@stephenwilliams1824
4 жыл бұрын
Viton O-rings
@rickanna8662
3 жыл бұрын
You didn't show how to do it!??
@transrus1
4 жыл бұрын
Best video ever . Lots of details on this . Hahahahahaha
@rickschwebke4710
Жыл бұрын
You did not show how to change out the O rings. All you did is talk about the kits
Пікірлер: 66