Would love to have one of these for under the gable end of my garage
@clydewarman1576
7 ай бұрын
I'd buy one of those for sure.
@kurtopalka5201
Жыл бұрын
Awesome job!
@tombreslin367
Жыл бұрын
wow! That was great work! 👍
@over60crafter
Жыл бұрын
Excellent work.
@jimrosson6702
8 ай бұрын
Very cool great job
@wasupfool5692
8 ай бұрын
Awesome work
@chrispelletier3661
Жыл бұрын
Very cool. Thanks for showing your process. Love your sign!!!!
@bradscustomsigns8585
Жыл бұрын
Thanks
@lstineman
Жыл бұрын
wow.. outstanding
@EdiCNC
Жыл бұрын
Excelente trabalho
@Harley1563
Жыл бұрын
Nice work Cuz 👍
@charlenerusso7829
8 ай бұрын
Super boulot un final magnifique
@infographie
3 ай бұрын
Excellent.
@Rafautomotopasja
2 ай бұрын
Mega praca i super efekt ,Wow :)
@Hotrod66149
6 ай бұрын
Oh hell yeah!
@Kaycee2C
6 ай бұрын
This is beautiful BOSS !
@bradscustomsigns8585
6 ай бұрын
thank you
@iamnotguilty
7 ай бұрын
This right here is BAD-ASS! Well done!
@bradscustomsigns8585
7 ай бұрын
thank you
@ledheadkustomplastic3442
7 ай бұрын
Amazing work Brother.. Love that sign 😎👍🇺🇸
@bradscustomsigns8585
7 ай бұрын
Thank you
@Suavellous
Жыл бұрын
Great video 🙌🏻
@bradscustomsigns8585
Жыл бұрын
thanks
@GyWO10
Жыл бұрын
That’s bad a$$ right there!!!🤩 Thanks for illustrating & explaining your process!!
@bradscustomsigns8585
Жыл бұрын
thanks
@RachelFraser-kb6ew
Жыл бұрын
So cool! I just stopped by your garage sale today
@bradscustomsigns8585
Жыл бұрын
Thanks
@rossgibson9208
7 ай бұрын
Oh my god that’s friggin amazing!!!!
@bradscustomsigns8585
7 ай бұрын
thanks
@TayDavis7276
9 ай бұрын
Awesome 🙌❤️
@bradscustomsigns8585
9 ай бұрын
thank you
@waynegeils2130
Жыл бұрын
Awesome
@JorgeRobinsonPavezReyes
2 ай бұрын
perfect😍
@treggmichelleliebler399
6 ай бұрын
Nice!
@robinp.9886
7 ай бұрын
Woww, Superbe création
@bradscustomsigns8585
7 ай бұрын
Thanks
@SJSSawdust
3 ай бұрын
very nice
@dmccaffe
Жыл бұрын
Watched 4 of your videos back to back and amazed by each. Thank you for posting these.
@bradscustomsigns8585
Жыл бұрын
Thanks, I appreciate that
@M3lv1n-VR46
Жыл бұрын
🔥🔥🔥🔥
@gary.pettineo
8 ай бұрын
WOW
@cellokustom9060
10 ай бұрын
Love this one! Great work! Do you sell your signs?
@ald.3449
Жыл бұрын
That's just fucking incredible!!
@bradscustomsigns8585
Жыл бұрын
Thank you
@ca_ged
Жыл бұрын
Teach me Obi Wan.
@TruthMotorsports
Жыл бұрын
So rustolium for spray, what do you use for rolling? What grit sand paper do you use when removing before rolling? Amazing work by the way
@bradscustomsigns8585
Жыл бұрын
I've been using dollar store foam rollers, at .75 each, I consider them disposable. 100 grit to remove all my overspray, 220 grit to clean it up for painting
@Rallsfam
Жыл бұрын
Love your work! What kind of epoxy do you normally use and where so you get it?
@bradscustomsigns8585
Жыл бұрын
thank you, I currently use Magic Resin, usually ships by next day
@ReevesLittle
Жыл бұрын
After you did the clear it looks like you set a piece of foam core on top (at around 5:05 minutes in). Was that making contact for some reason, was it a dust barrier while the clear cured or does it serve some other purpose? Thanks for the awesome walk through!
@bradscustomsigns8585
Жыл бұрын
thanks. Yes that was just a piece of coroplast to keep the air born contaminants off while it dries.
@ReevesLittle
6 ай бұрын
Thanks!@@bradscustomsigns8585
@kotsios1234567
Жыл бұрын
Hey Sir. You are awesome. Been doing such signs on my cnc but nowhere near the as quality of yours!! I would like to have your contact!
@bradscustomsigns8585
Жыл бұрын
thanks, you can find me on Facebook
@willbarnett205
Жыл бұрын
I love these signs. I struggle with paint. What spray paint do you use? Sand between coats? Thanks for any help
@bradscustomsigns8585
Жыл бұрын
Thanks. Predominantly Rustoleum spray, 3 "light" coats 20 - 30 min apart (don't try to get full coverage in first couple), let dry, light sand and then 1 more coat if needed.
@willbarnett205
Жыл бұрын
Thanks again. Sand with a 220 grit or higher? Thanks again for the advice.
@bradscustomsigns8585
Жыл бұрын
@@willbarnett205 I like to go at least that or higher, just enough to take off the shine
@kansaskutabuddy
Жыл бұрын
As far as the epoxy are you just pouring white initially then after it cures going back over it with the different colors? What type of squeeze bottle are you using?
@bradscustomsigns8585
Жыл бұрын
yes, the first layer is basically a filler because I don't use deep pour epoxy, and I use a slightly translucent white to avoid getting too opaque and ensure that the lights will still show through the final pour. This was the last batch of bottles, but I typically look for sales of similar type www.amazon.ca/gp/product/B08GP3P7RJ/ref=ppx_yo_dt_b_asin_image_o02_s00?ie=UTF8&psc=1
@MagnumPopeye
9 ай бұрын
Why would you not just use clear on the first half?? Would that not have saved you some white die and prep time? Or is there something I'm missing?
@bradscustomsigns8585
5 ай бұрын
@@MagnumPopeye it's only a small amount of pigment, and I think (and it's possible I'm wrong) it helps with to keep the top colors more opaque.
@xarshar9525
Ай бұрын
Hello, Can you tell me what kind of pigment do you use and in what proportions? All of my suppliers are telling me that the covering pigment will not let light through...
@bradscustomsigns8585
Ай бұрын
the white was tinted with Ecopoxy liquid pigment, and the Orange was tinted with Rustoleum bright orange paint
@rodolfogarza2042
8 ай бұрын
Great job,i like it!!! Is it for sale????
@bradscustomsigns8585
7 ай бұрын
made this for a friend
@packer34
10 ай бұрын
Man that is freaking awesome! Would you be willing to part with the gcodes? By the way what size is the sign?
@bradscustomsigns8585
10 ай бұрын
Thanks. If you find me on Facebook under the same name we can more easily communicate
@bradscustomsigns8585
10 ай бұрын
24" wide piece
@TheSheldo03
Жыл бұрын
How did you set it up to cut out on the back side? I tried and my cuts were almost an inch off.
@bradscustomsigns8585
Жыл бұрын
I plot my design in the exact center of the blank, so that after I do the first carve and flip it over, the reversed image is still in the exact center
@TheSheldo03
Жыл бұрын
@@bradscustomsigns8585 that makes sense! Thanks!
@jimyongue6172
10 ай бұрын
@@bradscustomsigns8585 I Think I understand what you are saying, but is there a trick to making sure the sign is positioned correctly when flipping it over? Is it OK if it isn't 100% lined up? Thanks and very cool video!
@bradscustomsigns8585
10 ай бұрын
@@jimyongue6172 well the consistent positioning is the key. I have a preference for a dedicated X/Y location (mine is bottom left), so when I set my zero for X/Y, it is on the same place for every piece I do, never have to reset, the only zero I set is for my Z. So I set my artwork in the exact center of my blank slab, carve my piece, and then when I flip it over, the art is still in the exact center of the blank on the opposite side, so you need only to flip your design to match its location.
@jimyongue6172
10 ай бұрын
@@bradscustomsigns8585 Thanks, I'm new to the CNC machine world. I have some trial and error ahead of me.
@robertosantana129
Жыл бұрын
How did you know to flip it perfectly that it would cut on the other side
@bradscustomsigns8585
Жыл бұрын
I just made sure it was exactly on center of the slab on top cut, and then ensured centered again when flipped
@rickycurry574
Жыл бұрын
This video is by far the best video from start to finish. I have a shapeoko 3 xxl with carbide create software and hopefully to upgrade to a better software soon. I just subscribed to your channel and looking forward to learning from you. You are too awesome. Do you create files and sell them?
@bradscustomsigns8585
Жыл бұрын
I've never really gotten into the file selling game, I've had a few people contact me looking for help and they have sent me a little tip in appreciation but that's about as far as I've gone.
@rickycurry574
Жыл бұрын
@Brad's Custom Signs ok I understand. I will be following you to learn as much as I can and I don't mind paying for some knowledge. I'm now following your Facebook page. Thanks for the awesome videos.
@rickycurry574
Жыл бұрын
@Brad's Custom Signs I have a question. Do you mind telling me what software you use to create the signs? I have carbide create but wanting upgrade.
@bradscustomsigns8585
Жыл бұрын
@Ricky Curry I'm using carbide create standard version. I may update to pro version or something different in order to start doing full 3d carving, I just haven't found the need for it quite yet
@rickycurry574
Жыл бұрын
@Brad's Custom Signs ok thanks. I was told I needed the expensive software to do what I see you are doing. Thanks for clearing it up. I will work with what I got.
@chadmccormack8036
2 ай бұрын
what type of epoxy are you using for the top coat
@bradscustomsigns8585
2 ай бұрын
I am currently using Magic Resin Tabletop
@kevinkelly6479
4 ай бұрын
Hi where do you buy the cnc i cant find any here in Ireland
@bradscustomsigns8585
4 ай бұрын
I got mine from the US (I'm in Canada), but I'm not sure about their shipping limitations. I would suggest joining a group or 2 on Facebook, and just ask other members that may be in your part of the world
@darinbolvin3663
Жыл бұрын
Do you notice an heat issues from all this LEDs?
@bradscustomsigns8585
Жыл бұрын
not at all, these strips are not very intense
@Rallsfam
Жыл бұрын
Could we get a link to the led lights you use? Thank you!
@bradscustomsigns8585
Жыл бұрын
LED's are from Amazon www.amazon.ca/gp/product/B085FRXVMC/ref=ppx_yo_dt_b_asin_title_o06_s00?ie=UTF8&th=1
@johnolz1886
10 ай бұрын
Very cool. Any chance you use VCarve Pro and sell the files?
@bradscustomsigns8585
10 ай бұрын
sorry, I use Carbide Create
@chuckmaloney429
3 ай бұрын
Can I come and spend a day in your shop
@bradscustomsigns8585
3 ай бұрын
😃
@cesuich
8 ай бұрын
Can you share what brand of epoxy you use?
@bradscustomsigns8585
7 ай бұрын
currently using Magic Resin
@thegoga_
5 ай бұрын
Hi do you epoxy the back?
@bradscustomsigns8585
5 ай бұрын
I do not, just sand it clean and install a hanger
@thegoga_
5 ай бұрын
@@bradscustomsigns8585 Thank you!!
@RCjunkie
8 ай бұрын
Can I buy your file?
@bradscustomsigns8585
7 ай бұрын
find me on Facebook
@BobBob-eh5sb
Жыл бұрын
Really great looking sign. You lost me though it looked like you glued the back on, then sanded it and then took it back off. I’m assuming to put the lights in it, but why not put them in first, then glue and sand? I missed the taking it off the first time and then wondered how you got the lights in.
@bradscustomsigns8585
Жыл бұрын
I put the back cover on the riser ring to keep the shape and rigidity while it is being glued. And I install the lights last in the event I have any slips and have to make some modifications.
@BobBob-eh5sb
Жыл бұрын
@@bradscustomsigns8585 Oh, ok. So a back cover, a riser ring and the front piece. Think I got it now. I do like the spend up videos, but I do miss some things. Thanks for the reply. And again, great looking sign.
@robertosantana129
Жыл бұрын
how deep do you usually make your pockets before you put resin i usually do .20 but i found i was using too much resin but i dont know if thats acceptable so recently i began a project with .10 i use less but it pours out however i will surface the project .02
@bradscustomsigns8585
Жыл бұрын
I'm typically at .15", but I calculate my epoxy for .125, so it's just a hair below surface
@robertosantana129
Жыл бұрын
@@bradscustomsigns8585 really so it's ok to be under the edge ?
Пікірлер: 113