Doug is the man! He did a valve job for me on some shovel heads and bored out my cylinders recently, got a 4sp trans in the works now, nobody id rather give the work too! Great video, i've been meaning to get into the camchest on my dyna for some maintenance.
@clownpocket
2 жыл бұрын
Who is Doug?
@clownpocket
2 жыл бұрын
I pulled out the chain drive and put in the S&S gear drive kit on my 2001. 509 cams. Did that at about 30k, just turned 50k. I hope my top end lasts, I really don’t want to fuck with this motor any more than that. I’m in Brooklyn so if I need help can I look you up?
@MrGerryoc
3 ай бұрын
What a butcher wouldn’t let him sweep up in my shop
@bad-foot
2 ай бұрын
🤡
@JuanRodriguez-wt7fv
8 ай бұрын
Bro what the hell invest in a cordless drill. Whats with all this noise.were in the 20 century.
@JuanRodriguez-wt7fv
7 ай бұрын
Sorry I didn't mean it to sound so bad. Sorry.
@56rcb
8 ай бұрын
I wouldn't let this butcher within' 10 feet of my engine!
@cj8172
6 ай бұрын
He didn't butcher anything tho. I know what you mean but the engine was fukd already so he just pulled it apart the no non sense way. I'm sure he knows his shit pretty good.
@michaelmitchell5909
Жыл бұрын
Is the screamin eagle cam plate any good?. I have an 04 rk that has a 95" kit on it with that plate. That's what I was told, I did confirm the cam plate and 525 cams, but will the bearings in the cam plate hold up? 38 thou miles on the bike... Thinking about upgrading to the fueling oe plate
@bad-foot
Жыл бұрын
Yeah the screaming eagle cam plate is good but now with the fueling stuff everything gets upgraded to hydraulic tensioners which I much better
@michaelmitchell5909
Жыл бұрын
@bad-foot I thought the screamin eagle plate had hydraulic tensioner in that kit?....are they not?
@bad-foot
Жыл бұрын
@@michaelmitchell5909 some do and some don't you have to pull off the cover and see what you got going
@michaelmitchell5909
Жыл бұрын
@bad-foot hey man, just want to say thanks for responding back, I really appreciate that alot...,as far as my tensioner they are hydraulic screamin eagle. I'm just gonna run that setup for now, I use Lucas 20 50 in the motor and it runs good....I use tribodyn 75 140 in my gearbox, that's good stuff man, u shld check it out. They make 20 50 for vtwins also....it's more expensive than any other brand but it's on another level of quality than the other brands....even amsoil and Lucas or redline.
@user-uk4sk5io3h
8 ай бұрын
Does the age of the motorcycle affect the wear of tensioners? My 2003 DWG has 6,500 miles.
@bad-foot
8 ай бұрын
No it's only mileage that puts wear and tear on them
@user-uk4sk5io3h
8 ай бұрын
@@bad-foot Thank you for your answer
@tompeppint.v.3803
Жыл бұрын
I didn't know you could remove the cam cover without relieving the valve spring pressure 1st? Is that common practice? I've always collapsed the pushrods or removed the rockers before removing cam cover?
@derrickw5660
8 ай бұрын
I believe you’re right but he started with the top in he only removed the cover to look at what was going on…
@tompeppint.v.3803
8 ай бұрын
@@derrickw5660 you don't want all that pressure on the plates , that cover helps support the cam plate
@tompeppint.v.3803
8 ай бұрын
@@derrickw5660 you should or several hundred pounds will be pressing down on the cam plate held in by those tiny Allen's 1/4" I believe
@derrickw5660
8 ай бұрын
@@tompeppint.v.3803 im sorry about that i meant to say is how do you relieve the pressure when the motor is out the bike on a enigma stand….
@tompeppint.v.3803
8 ай бұрын
@@derrickw5660 sameway as in the motor , you either have adjustable pushrods you can loosen or pop open rocker boxed and back off the Ricker arms
@Thunder_Bear_mg
Жыл бұрын
New subscirber here but just noticed you haven't put out any new content in the last 3 months. Is this a temporary or permanent hiatus?
@user-uk4sk5io3h
8 ай бұрын
at what mileage such a failure occurs
@bad-foot
8 ай бұрын
Motor had 43k miles on it suggested maintenance for the cam chain tensioners is 20 to 25k
Пікірлер: 33