To do this test, should we put the tray in or leave it out? Does it matter?
@courtneywilson4213
Жыл бұрын
What kind of -temps should I be hitting? I have a medium which will go down to -40s during vacuum freeze time prior to dry time. New large I cannot even get it to -20 freeze setting … usually go to -17 and just sit there. So I stop machine and change setting to -10 (default) and it will move on… but still not seeing the low temps I get with medium. Freeze test with water got 7-8 rings and when cooling prior to run it is visibly chilled starting to ice to 3-4” from front edge … but when actually has food going it’s at least 6-8 inches from front. Not sure if I should be concerned. Thank you for any input.
@IgoOutlateAtnight
4 ай бұрын
Thanks for channel. I know they say if you move the machine you should let it sit for 24 hours to I assume let Freon sit. What id you bump the machine a little but don't move it? For example, reinstalling the neoprene gasket and you push on the machine and it shakes a little? Is that a concern or should I wait the 24 hours?
@msu836
6 ай бұрын
Have had my machine for about 1.5 years. Moderate use. Harvest Right small. Did a function test after 30 minutes results as follows: Tray 53F; Room 70F; Freeze after exactly 30 minutes -15F. Then moved on to the vacuum, after 41 minutes hit 442 mTorr with temp of -21F. I am questioning whether I need more freon as my last few batches took a bit longer and only had 3 freeze rings from the forward to back. Thanks
@freezedryerrepairsupport
6 ай бұрын
If your only have 3 rings your most likely low on Freon. HR has been having issues with leaks in machines under the foam however. You do have a limited 3 year warranty on this part of the machine
@lisanelson1457
15 күн бұрын
I have an xl that’s 1 1/2 years old. It keeps getting stuck in the freeze cycle. It won’t move in. It’s been running for 89 hrs, just freezing. I tried to warm trays and it stays at -7
@yauney1
Ай бұрын
I just bought a 2018 HR medium FD. When i touch the leaf it takes me To the liquid or non-liquid selection screen. It doesn't take me to a functional test screen. Is that a development since 2018?
@freezedryerrepairsupport
Ай бұрын
It likely was part of an update if your having issues with vacuum on this older machine I would check the o ring that makes the 90 degree turn for the vacuum hose
@kellycunningham5144
Жыл бұрын
What numbers should we be looking for?
@freezedryerrepairsupport
Жыл бұрын
Good morning, we want at minimum 500 mT after running the freeze for 30 min than adding the vacuum for 30 min. After people complete the fox we normally see in the 300s or lower
@brianingram1415
9 ай бұрын
Do you have any idea why my vacuum pump does not turn on when I test the vacuum setting? I've verified that the pump switched is turned on and I even tested it by plugging it directly into a wall outlet and it works fine. Also tested voltage at the pump power plug on the rear of the main until and it's not receiving any power when running the vacuum test.
@freezedryerrepairsupport
9 ай бұрын
I would check all the wiring. If it’s not getting power to that plug a wire has to be bad or the plug itself. HR should have that plug they can send to replace
@EveryDayAmityShay
7 ай бұрын
Hey i found you because my freeze dyer seals fine but wont freeze. How do i fix it? I had milk in there for 8 hours and it never got under 46f
@freezedryerrepairsupport
7 ай бұрын
Check out my video from 2 guys and a cooler. Likely an issue with the freeze dryer as a whole
@EveryDayAmityShay
7 ай бұрын
Ok. I'm pissed. 3,500k down the drain and a recession
@freezedryerrepairsupport
7 ай бұрын
Have you reached out to HR they have a 3 year warranty for this system. They will want you to pay shipping if it’s been over 1 years however
@myckielhaynes
4 ай бұрын
HI WHY MY NEW XL RATTLES TO START BUT NOT STARTING....IT SAY FREEZER RESTART DELAY
@storme145
11 ай бұрын
What if the freeze shuts off at 15 minutes?
@stehlfamilyfarm6886
8 ай бұрын
Hello my wife screen keeps freezing at different times ( lagging) any recommendations ?
@freezedryerrepairsupport
8 ай бұрын
Good afternoon, I would suggest reloading the software as it will remove all the old log files. These are not made to hold a lot of information
@twinks8580
23 күн бұрын
If I go into functional testing and click on freeze, heat, or vacuum it will turn that item on, but the unit and screen locks up. I can't turn it off or exit. I have to turn the main power off to reset. What's wrong?
@uturd09
8 ай бұрын
Be nice if you showed what the read out is supposed to be if its operating properly
Пікірлер: 22