Thx for short, direct video. Need to splice sewer line that is not a prefab bend, i.e.: 22.5 or 45 bend. This is encouraging.
@patrickkariuki2460
Жыл бұрын
I need to remove a 2m long pvc pipe encased in a concrete floor slab. How do I soften the pipe so I can pull it out once it softens?
@billsmith987
3 жыл бұрын
Old school... love it👍
@user-bn3bp9pd9c
24 күн бұрын
What tools is used?
@mrjcbuc
2 жыл бұрын
if i just want to bend a couple of thin pieces at 45 degree angles for a volleyball spike trainer, could I use a heat gun?
@JohnThePoolExpertGuy
2 жыл бұрын
Yes a heat gun will work just fine
@stevenhaley443
4 ай бұрын
OK. I've got bent pvc pieces that I want to reuse. How would you straighten a bent piece out?
@JohnThePoolExpertGuy
4 ай бұрын
Basically the same way but be careful gluing fittings to pipe that has already been heated because it shrinks
@JamokaJoe
2 жыл бұрын
Thank you for the video! Will it stay flexible when it slowly cools (without the use of water)?
@JohnThePoolExpertGuy
2 жыл бұрын
Yes its the same either way.
@JamokaJoe
2 жыл бұрын
@@JohnThePoolExpertGuy Thank you, John! 👍
@ScoutSniper3124
Жыл бұрын
If you had something flexible but solid in cross section but somewhat heat resistant (maybe a pool noodle wrapped in foil tape) to put on the inside AFTER you heat, but BEFORE you bend, that would help keep the pipe from collapsing, and even out the bend radius. My 2 cents, thanks for the video.
@JohnThePoolExpertGuy
Жыл бұрын
Yes that works I'm also seen people pack it with sand and other things........ whatever works!
@connorworley9450
Жыл бұрын
I feel like its not worth the effort
@joseyman1017
5 жыл бұрын
Can i get that inspected if its septic drain
@JohnThePoolExpertGuy
5 жыл бұрын
Usually it's fine with inspectors but it depends on where you are
@fortyozsteak
2 ай бұрын
Can I do this if there’s a wire already in the conduit?
@JohnThePoolExpertGuy
2 ай бұрын
Yes it should work fine
@fortyozsteak
2 ай бұрын
@@JohnThePoolExpertGuy the conduit is like 25’ long and I’m looking to bend it back straight. The curve is only like 10-15 degrees over that 25’. Seems like it should be pretty easy aside from just digging it all up initially
@pedrosanchez3148
2 жыл бұрын
Whats the attachment called?
@JohnThePoolExpertGuy
2 жыл бұрын
I think it is called a weed burning torch. You can buy them at Home Depot
@UBGood
9 ай бұрын
Always that one guy, 😂 who thinks outside of the box 👍
@donguadalucio1405
2 жыл бұрын
What happens if you burn it just a little bit; is it still ok to use it underground?
@JohnThePoolExpertGuy
2 жыл бұрын
It should be fine
@donguadalucio1405
2 жыл бұрын
@@JohnThePoolExpertGuy Thank you.
@bonsummers2657
11 ай бұрын
Just do it.
@blain5827
4 жыл бұрын
Pretty sure if you cap the ends it works faster
@billsmith987
3 жыл бұрын
It doesnt
@negenzculz6789
4 жыл бұрын
can u bend 180° of 2inches size of pvc pipe?
@JohnThePoolExpertGuy
4 жыл бұрын
Sure that's how we make spas round
@rosertaylor6139
3 жыл бұрын
You didn't show how to bend that thickness without kinks. It did kink on you once.
@jfromtn7410
Жыл бұрын
have you ever tried this on 3 inch schedule 80
@JohnThePoolExpertGuy
Жыл бұрын
Yes it takes a lot longer
@merlion4541
4 жыл бұрын
Can i use a gas torch for this?
@merlion4541
4 жыл бұрын
I have a 3 metre pvc pipe that has not been used for 2 years and not its kinda bent. I want to do hydroponics so the pvc pipe needs to be straight. Can i use this technique with a gas torch?
@JohnThePoolExpertGuy
4 жыл бұрын
Yes
@merlion4541
4 жыл бұрын
@@JohnThePoolExpertGuy thank you for the reply sir :)
@GemmyHeart
Жыл бұрын
Main products: sealing gasket,gland packing,PTFE/graphite/asbestos products, ceramic fiber products, high temperature heat insulation and fireproof material. Free technical support (sealing, heat preservation, heat insulation, fire prevention problems) All products 1 piece can also be customized, 30 years of service experience, fast and safe shipping anywhere
@durhamjut
8 күн бұрын
How about not getting to close to the propane tank....
@quevenmz8456
Жыл бұрын
By the time your finished heating up that pipe, ive already glued 100 ft of 2” pipe
@robbrown6495
Жыл бұрын
Oh dear - I seem to have misplaced my industrial grade flamethrower!
@AquaTech225
Жыл бұрын
Hopefully your not a true contractor or professional wouldn’t. Haven’t seen any of the real ones use anything but fittings on a pool build. Keep that for the non jobs that’s your own. Be a professional and use the fittings. It’s all paid for in the agreed upon an signed contract of the job. What your doing is just cutting corners
@Nctbgs
8 ай бұрын
Lol , I worked in a pipe factory, we heat the pipe up to make the bends , we do it in an oven style system but his method is just as good . We charged $22.00 more for bends , you can do the same yourself for almost nothing .!
@dutchvanderlin5556
7 ай бұрын
Shut up you obviously have no idea what you’re talking about. Ever heard of TDH? Probably not.
@barbararitchie1800
6 ай бұрын
Aquatech U clearly aren't a person that is good with your hands
@GoodOldGreyMatter
22 күн бұрын
I’d rather it done this way instead of adding many potential fail points FYI Mr. Aqua tech guy with glue. Just my thought
Пікірлер: 46