NOTE : The suction to be done on the syringe is near to 50ml if you are doing full oil immersed method follow the below link: kzitem.info/news/bejne/rW963Y6ImKWIko4si=gb2auuR16Y7Z5jdh
@zBanditGuy
2 ай бұрын
Im rebuilding a hpfp for a 2010 mini cooper, the design looks very similar, would these gaskets work on it too?
@bimmerhacks
2 ай бұрын
@zBanditGuy it looks the same... Try the high temperature (brown color) O-ring which tight fits to the compressor springs. See my new video in the comment
@jacobdavis787
14 күн бұрын
When I rebuilt mine I got it down to 14mm or so. Is this bad? Should I be aiming for 19mm only?
@SaltyDiver
2 ай бұрын
Very well done!
@renegonzalez7391
18 күн бұрын
Would you happen to have a write up on a website ? Looking for those x - rings and that tool you used to open it up
@BEAMERNOOB
11 күн бұрын
The link isn’t working
@bimmerhacks
11 күн бұрын
Forgot to remove the link. Store no more active. Email me your address in bimmersword@gmail.com I'll check the shipping charges and let you know
@deffbichsweet2461
Ай бұрын
I rebuild my pump and i hade 19mm on dighprha.. But i put back and its stil dånt wanna work shows me same fault code 29F2 hight pressure fuel system. And this only code left. Car starts and can drive but right away comes limp mode and halvs engine pic. And feels like missfire. I head the pressure and its same pressure as before
@bimmerhacks
Ай бұрын
It might have trapped air or oil might be leaking from the HPFP. When u installed the o-ring/x-ring might be loose or got cut!!!
@deffbichsweet2461
Ай бұрын
When I put o rings they go Smooth And i pulled 19mm and i left little bit in pil to take in all oil in on wake up the digrahp. And I check after 1 hour oil level was same. After i pulled more oil in.
@bimmerhacks
Ай бұрын
@@deffbichsweet2461 O-ring must be tight fit. As you might have noticed the original O-ring was so tight that it was difficult to get it out. When the HPFP turns it makes more pressure inside and the tendency of oil to push out will increase
@899388819
22 күн бұрын
Exelent work!
@davidaranda1862
Ай бұрын
I cannot see the seal kit you have provided link to, is there another one?
@bimmerhacks
Ай бұрын
Store closed due to lack of order. Drop me email with your address to bimmersword@gmail.com I'll check the shipping charges and let you know how much it will cost
@sixdays77
3 ай бұрын
Do you have some part numbers for seals or measurements? Specs needed for company what makes o-rings and x-rings
@bimmerhacks
3 ай бұрын
Please see description for sizes. Part number is shop specific so I don't think it will work in your area, those are listed below Hpfp x-ring - 37757 Oil seal 62856
@zakash613
3 ай бұрын
how long does this modification last? have you had to rebuild the pump again after having done this?
@bimmerhacks
3 ай бұрын
This was done 2 weeks back. I had done similar fix 3 years back and its still running fine and crossed 25k miles. If the pressure inside the hpfp is higher then there is more possibility of early failure
@moisesgonzalez8103
3 ай бұрын
Hello, good friend, I have bought 3 pumps since they come defective, supposedly new ones that have a 27mm membrane, do they all come empty of oil? thank you
@bimmerhacks
3 ай бұрын
kzitem.info/news/bejne/uYhjwG2KoGZnq3Ysi=pibuPxaZTn9wx__Z As I explained in this video 27mm means there is no oil pressure inside the HPFP, it might have oil in it if fuel didn't penetrate in but NO USE. If you're repairing go for fully immersed method which I recommend rather than filling oil through oil seal. U can install the oil seal at the end same as I have shown in this video once all other parts has been installed immersing in oil. Vacuum must not exceel 40ml on a 60-100ml syringe
@moisesgonzalez8103
3 ай бұрын
great then 100% these pumps are pressurized internally with oil and their optimal and long-lasting operation is the load of oil to lubricate these internal parts, what I don't understand is why the new pumps do not have this pressurization, I imagine low quality Chinese production, this Chinese pump, is it possible to fill it with oil and make it work correctly? Thank you very much for the info
@bimmerhacks
3 ай бұрын
@@moisesgonzalez8103 open it up and see. Don't buy refurbished one, when you rotate the itself you can feel a grinding sense. Buy junkyard one and fix if your diaphragm or any springs are leaking.
@1kontrabida
3 ай бұрын
Quick question is there a fix if the diaphragm is leaking?
@bimmerhacks
3 ай бұрын
No fix for Diaphragm. Go and get a junkyard one so that you have spare compression springs as well.
@1kontrabida
3 ай бұрын
@@bimmerhacks thanks bradah
@user-ek5qu6he6m
3 ай бұрын
dimensions of the o ring on the outside? where the 2 halves are compressed?
@bimmerhacks
3 ай бұрын
No need to change it. I have repaired 3 HPFP and none did I change
@user-ek5qu6he6m
3 ай бұрын
@@bimmerhacks thank you
@bimmerhacks
3 ай бұрын
@user-ek5qu6he6m kzitem.info/news/bejne/uYhjwG2KoGZnq3Y I used to miss some information that I used to convey in succeeding videos. Fixing and vloging together is a bit difficult ;)
@1kontrabida
3 ай бұрын
21:00 when I was cleaning this orifice I had some small chunks that came out that turns to like sand when u press on it a little bit, also after putting the diaphragm started to leak a little bit of oil, have encountered this? Also I use thinner oil 5/50 just to check but I think it needs a thicker oil to put inside . Any advice thanks
@bimmerhacks
3 ай бұрын
Thinner than 0w20 will be too light that it will not do the job of lubrication. If there is no lubrication there will be more wear and metal shavings will accumulate like sand. I think you can use 5w30 if you want thicker but too thicker might not work properly as the flow of oil has to be fast to compress the pistons. I had tried the thicker differential oil 3 years back and it was running fine, but one day out of curiosity I opened up and found that it was not lubricating as it should and was accumulating metal shavings.
@1kontrabida
3 ай бұрын
@@bimmerhacks I was thinking the same, 15w40 ok?
@bimmerhacks
3 ай бұрын
@@1kontrabida it should be OK, just my thoughts not a pro 😉
Пікірлер: 39