Salamat sa pag upload sir..ung sakin kinabitan ko pa power supply simple lang pala remedyo.
@beniptec
6 ай бұрын
sir baka need nyo cctv merun tayo mura lng
@waleedabdullah8381
2 жыл бұрын
Thanky very much
@sherazshafique135
3 жыл бұрын
Upload more video thanks!
@deltabcctv2204
3 жыл бұрын
upload more troubleshooting video
@omartaylor2975
Жыл бұрын
The diode is there for protection i thaough you were going to replace it
@beniptec
Жыл бұрын
bridge diode if shorted required to replace but if the protector diode even not it will work but if you have replace
@brianmeche2341
Жыл бұрын
Does the DS-7608NXI-I2/8P/S have the same diode? My POE suddenly stopped working on my 8 channel. What causes the diode to short?
@beniptec
Жыл бұрын
builtin power supply same have this protect
@brianmeche2341
Жыл бұрын
@@beniptec would it be better to use an external POE switch instead
@learning4348
2 жыл бұрын
Hi I think I have the same problem with my Nvr . My one is a 4 channel. Where can I buy that new part ? Can you tell me you aren't anywhere near Ireland so you can fix my Nvr ?
@beniptec
2 жыл бұрын
just removed and test
@beniptec
Жыл бұрын
4 ch is not same to 16 ch let me know your device model
@charlesjoshua727
4 ай бұрын
Thanks for the video. I have Hikvision PoE nvr model - DS7732NI-K4/16P with same issue, it has 52Vdc but I could not find the said diode on the board how do I go about it Sir. I really need your help urgently. thanks.
@beniptec
4 ай бұрын
send picture main board
@senorpepper1
Ай бұрын
Hi please help, I have a DS7616NI-I2 with no 12v to board and no 52v to POE. PSU is good, please advise which diodes I should check?
@beniptec
Ай бұрын
What is the issue your facing plz note the issue
@senorpepper1
19 күн бұрын
Hi, I checked the power supply which is working fine but nothing on the board is working.
@Aldoraine31
3 ай бұрын
Hi, I have a DS-7608NXI-I2/8P/S which ports 5-8 have no POE, 1-4 work fine, any help would be great ?
@beniptec
Ай бұрын
I will chk this isseu for you later i will reply
@nicolamanca1354
Жыл бұрын
I tried two different poe ipcams on all 4 poe ports of the nvr but they don't work. I had to power the ipcams via an external poe switch. Do you think my nvr is broken? How can I fix it? The model of the nvr is Hikvision HWN-4108MH-8P (4 ch) Thank you
@beniptec
Жыл бұрын
check all diode near to poe port if ok the ic controller poe isseu or resistor
@beniptec
Жыл бұрын
make sure adaptor is 52 volts or 58
@silencemakesnoise
2 жыл бұрын
Hi, what component function that you have replaced
@beniptec
2 жыл бұрын
this surge power protector. but sometimes even no surge this parts damage or shorted.
@gevinsoriano
2 жыл бұрын
@@beniptec hi sir the diode you removed was with the label of P804 5PGG?
@beniptec
2 жыл бұрын
@@gevinsoriano yes sir only that diode big size protecting 52 volts dc for poe you can removed. just removed no need to replace new parts but first if this diode is shorted. because if this not short this another parts need to replace that is the main ic driver function is poe switch and control. may next video will upload this more deep trouble shooting... kabayan k ba sir
@gevinsoriano
2 жыл бұрын
@@beniptec yes sir kabayan hehe. Regarding sa question ko sir, natamaan ata kasi ng kidlat yung line namin kaya may pumasok na 24000w dun sa nvr kita ko dun sa camera poe settings. try ko alisin yung diode sana maayos. Thank you Kabayan.
@djian4100
Жыл бұрын
Kabayan ask ko lngme lng po ba yung sa poe ng nvr ds7609 tatangalin n diode? Pag
@beniptec
10 ай бұрын
sir iba iba un problema sa poe ng nvr minsan un driver ic sa poe. need talaga troubleshoot
@roelortiz7250
Жыл бұрын
wala naman pong pinalit dun sa diode. so ok lang po ba yun? wala na syang protection sa surge.
@beniptec
Жыл бұрын
marami n ako nagawang ganun wala nmn feed back .
@djian4100
Жыл бұрын
Sir ask ko lng po no power din yung nvr ds 7600 ko pag open iilaw sandali ang cam tapos wala n ilaw ang poe
@beniptec
Жыл бұрын
try un plug un ipcam mo at tesf mo pa isaisa baka may short sa isa mo cam if ganun parin chk mo un diode protec sa poe baka short or leak
@kinlee5111
6 ай бұрын
My nvr DS-7604NI-K1/4P port 1 poe not working. The other 3 ports are fine. The poe page shows a red cross on port 1. What is the problem?
@beniptec
6 ай бұрын
check the diode for port 1
@manafsaidusaidu9950
2 ай бұрын
Hi sir, same nvr 12v short, 12 volt drops to 4 voltage.. Any solution pls.
@beniptec
Ай бұрын
Chk new adaptor first then second power circuit ic and surge diode protector and chk dsp temp
@devinpatel5342
11 ай бұрын
my Nvr 3 ports working and other 13 not working is this a same issue?
@beniptec
11 ай бұрын
model please
@beniptec
11 ай бұрын
this another issue just share me the model
@omarrwanda8157
Жыл бұрын
Same problem with this
@omarrwanda8157
Жыл бұрын
Only to remove the diode and short the two way?
@rechineegalang9116
5 ай бұрын
What is the value of POE protection component?
@beniptec
Ай бұрын
Surge protect diode you can removed
@djian4100
Жыл бұрын
Diode po ba ang tatagalin ko send ko po yung video ng nvr ko
@beniptec
Жыл бұрын
video mo nga sir send mo whattsapp ko 00971501665113
@GEE9043
Жыл бұрын
hi dear bentech, i face same problem, poe no power, but sometime restart have power, is it same remove this?
@beniptec
Жыл бұрын
can u send me video for the isseu
@beniptec
Жыл бұрын
and model
@beniptec
Жыл бұрын
first you have check this poe 52 dc
@beniptec
Жыл бұрын
this rg-45 issue
@ukqatar2535
7 ай бұрын
@@beniptechi can you share your Facebook id or WhatsApp
@djian4100
Жыл бұрын
Hello sir puwede ko po pa gawa sa inyo ang akin nvr same issue po sa poe
@beniptec
6 ай бұрын
baka sir gusto nyo bumili ng cctv sakin cheap price
@nitsab
9 ай бұрын
I have NVR POE not working the same you but I can not do
@beniptec
9 ай бұрын
model ?
@djian4100
Жыл бұрын
Minsan po pag nag reebot ako ng nvr meron ilaw ang poe ko pero after mga.ilan minutes wala n lahat ilaw poe
Пікірлер: 65