"Some people would kill for an ass like this." lol
@diaracing
9 жыл бұрын
Hatton Garden Heist brought me here ;)
@chrisjones2364
9 жыл бұрын
Nice drill. I'd love to play with that for just one week. Hilti is pricey but they sure make some quality equipment. I think a lot of the time the guys that bitch about the cost of their products are really just jealous maybe. I'm one of them I can honestly say. I can still remember the first time I used a 480v drill. It was the pentruder model. I drilled an 8" dia. 12" deep.....45 seconds. I thought I was dreaming. Nice job man.
@fakesandy
9 жыл бұрын
Every bank robber in the world is watching this video ;P
@kollenberg74
8 жыл бұрын
Rob, this happens all the time. the wall is 20 some years old. we are drilling the holes for equipment upgrades.
@nasaruddinajare9926
4 жыл бұрын
Very good !!
@makeminealarge1
9 жыл бұрын
Brilliant, hope they don't get caught.
@MM0SDK
9 жыл бұрын
My god, what a buzz that must have been, crawling out of the hole inside the vault.
@LVL1Yo-YoGuy
8 жыл бұрын
I noticed all tools have close resemblances the color and name brand are the two differences, the wanker using the tool is what really matters. SAFETY FIRST MATES👷 cheerio
@natalka8811
5 жыл бұрын
Wspaniała maszyna.
@ibrasigma711
9 жыл бұрын
It is Hilti Co. The poor operator should be sitting under an umbrella branded with Hilti logo.
@mediacoregroupph
9 жыл бұрын
Do they go around in tangerine colored vehicles? They do here in the Philippines
@Pro1er
4 жыл бұрын
Milwaukee is coming out with an M18 version.
@olegandrienko386
10 жыл бұрын
во во и щас на такой машине еду бетоны просто тема советую
@kccoringandcutting2039
7 жыл бұрын
NICE VID!
@phil5888
9 жыл бұрын
This drill must draw quite a bit of power under load. If you tried making a hole in an Italian bank vault you would end up tripping the whole street.
@MM0SDK
9 жыл бұрын
So this is probably the video the robbers used....lol.
@kollenberg74
9 жыл бұрын
***** hmmm i should get a cut
@kollenberg74
12 жыл бұрын
3X 20" holes at 16" Arrival on site 7:30 packed up at 11:30
@dekonfrost7
11 жыл бұрын
thats great time
@RA30st08
9 жыл бұрын
I know this the DD500 but have you heard that a DD350 was used to break into a vault in London? Media is currently estimating the theft could be as much as £200 million but they aren't sure yet, as it was a 'safe' deposit. Yours is the most detailed video I've found that could be used as a DIY guide....wonder if they used your video?? The wall was 2m thick....can you get extensions for these? Or do you think they had to make their own?
@kollenberg74
9 жыл бұрын
Yes, you can core drill almost any depth, all manufacturers sell extensions, sometimes long barrel core bits are made up or ordered for thick drilling.
@neanam
9 жыл бұрын
That's why I'm here I wanted to see how could this drill get through the safe
@andrewtucker5917
9 жыл бұрын
RA30st08 The HILTI could do it, through concrete, same bit more extension. But apparently the 'heist' was 2m through reinforced concrete rebar, and you'd have to be 4yo small to get through a 350mm, 2m long tunnel. Imagine a 30cm ruler held out infront of you.
@kollenberg74
9 жыл бұрын
I think they must have drilled a series of holes to create an opening, i'm guessing at least 600 mm in diameter. that would require around 19 holes at 100 mm, looking at 45 per hole.
@RA30st08
9 жыл бұрын
kollenberg74 Wonder if they got a kid or dwarf in on it....just like Bad Santa lol
@ggjkjvjdhjijch334
4 жыл бұрын
Gut
@iversonjcameron
10 жыл бұрын
Nice drill nice setup...but on big holes just use hydraulics.....check out....core drilling a 43
@grzegxyzasd7207
27 күн бұрын
O na sucho może się zatrzeć, jak mawiała pewna dziewczyna 😜
@AndriiTurchynRieltorDnipro
10 жыл бұрын
Рабочая лошадка
@crbassassin
8 жыл бұрын
crack that vault
@whyexactly
9 жыл бұрын
This might b a stupid question, but how do you get the material out after?
@kollenberg74
9 жыл бұрын
whyexactly Ha you didn't watch to the end :)..... drill until almost through then snap the core and pull it out.
@elizabetegeraldinasilvabet913
9 жыл бұрын
Elizabete geraldina silva Meu nome é Elizabete trabalho com Desentupimento e Hidráulica na Empresa SDB e quero saber se ela trabalha também caixas visita na hidráulica? quanto custa e forma de pagamento,se é a diesel,e quanto tempo trabalha por litro e posso trabalhar onde existem pontos com pedras.
@lunarstrain7186
6 жыл бұрын
no chance of robbing it now, the owner has installed high tec alarm systems including heat and vibration systems.
@JohnnyMotel99
8 жыл бұрын
Did the concrete guys forget to lay the formwork for this hole or what?
@scottylans
9 жыл бұрын
I'm curious if anyone needs a used one of these? I've got one going cheap, only used to drill 3 times. Thx.
@johnrichardson82
3 жыл бұрын
How much did you sell it for
@user-ks8xd5jc9s
9 жыл бұрын
We have the core drill bit for HITLI
@user-gh7ey2eq5v
4 жыл бұрын
Арматура была в бетоне????????????
@star4983
4 жыл бұрын
How much cost this hole ?
@dremel73
9 жыл бұрын
wtf! what NM torque?
@lengthmuldoon
9 жыл бұрын
how does the "concrete plug" come out?
@kollenberg74
9 жыл бұрын
Bertie Blue You have to drill to the full depth of the barrel and then use a wedge to snap the core and pull it out.Add an extension to the bit and drill again, repeat until through the wall.
@lengthmuldoon
9 жыл бұрын
kollenberg74 Thanks mate, do you know anything about safe deposit boxes? haha
@user-wd7pv9ld9d
4 жыл бұрын
DD 200?
@user-lo2vx6it2t
3 жыл бұрын
How much per our? Or for hole
@osservatoreesterno2398
6 жыл бұрын
E La Madonna !!!
@ranaarifbilal8884
4 жыл бұрын
3 year experience Concrete cutting machine operator .I need a job
@PBKIDSRGREAT
9 жыл бұрын
Came here from imgur like if you did the same
@user-gu1hl2kx2k
4 жыл бұрын
this video doesnt tell which bank to target
@mickyevans1844
9 жыл бұрын
hilti is the guvnor.hehe
@44region
10 жыл бұрын
Перфоратор 80 лвл
@ArkhipovIlya
9 жыл бұрын
на кой там ключ? патрон от руки должен закручиваться!
@MegaMishka88
9 жыл бұрын
он ключиком держит чтобы не вращался патрон
@ArkhipovIlya
9 жыл бұрын
Патрон с такой коронкой провернуть тяжело. Обычно вставляется коронка в патрон, и гайка накручивается от руки.
@MegaMishka88
9 жыл бұрын
обычно-это когда коронка обычная, а тут елдень
@iversonjcameron
11 жыл бұрын
nice video....check out mine.....core drilling a 43"
Пікірлер: 78