Your videos are just fine. Ignore the complainers.
@lexstarv.p.9171
3 ай бұрын
Your demonstrations are so clear and precise, thanks again for another awesome video.
@ayubtechke4294
3 ай бұрын
This is not for beginners if you understand what is happening no matter the noise you will get it 😂. Nice work Sir
@pedrojuarez2688
2 ай бұрын
Saludos desde Venezuela, excelente video.
@Fardeenfarwest
3 ай бұрын
Thanks Tevz for these video. Excellent work. ❤
@shopyd
3 ай бұрын
Hello sir.your videos are perfect and very helpful.is there a way to contact you for asking questions about tv repair.i repair tv and others too.thanks
@JeanDAVID
3 ай бұрын
you are the best electronic guy on tv repair !
@lorenzolopez8512
3 ай бұрын
Jejje los que sabemos un poco de electrónica,el audio es lo de menos solo con mirar lo que hace sabemos que está haciendo
@estebansuarez2957
3 ай бұрын
Hola tvz y no era mejor hacer un bypass como hizo en otro video ademas se ahorra en componentes 🤔
@aungzawoo9926
3 ай бұрын
i always see your video good teaching i love it
@venerandarain3
3 ай бұрын
thanks for sharing your modification skill sir. glad to watch your video again after several days.❤
@SintoVillena
3 ай бұрын
What is the name you used the temporary fuse??
@tevzTVTevatronics
3 ай бұрын
resistor
@yowunpansilu
3 ай бұрын
Tevz we need other electronic repairs too not just tv s
@cmcchrisable
3 ай бұрын
I wanna reach out to u to ask for guidance on a tv repair
@riasoria7411
3 ай бұрын
Please don't skip adds❤
@pacmanbob4260
3 ай бұрын
I think the back ground noise is great ! I’m watching a repair so I don’t mind - I especially like the rosters ! !
@entechdroidboardemulator9533
3 ай бұрын
I want to come over and learn
@kaizen1071
3 ай бұрын
Teşekkürler Tevz bey. Harika iş. Sağlıklı günler.
@bachirhannouta5532
3 ай бұрын
Thanks from moroco
@greendata1
3 ай бұрын
that was awesome
@Scrollermania1963
3 ай бұрын
@tevTV, what kind of device do you use ? To Discharge you're Capacitors ? Do you use a ground Clip, attached to wire, attached to a Resister, that attaches to Discharge metal Rod, that you simply touch to main, Capacitor.+ Positive Terminal ? For 5-10 seconds ?
@tevzTVTevatronics
3 ай бұрын
the resistor 220 ohms 20 watts.
@mubashirnoob5434
2 ай бұрын
Good working
@balabala6610
3 ай бұрын
Thanks sir
@ahmadmeratzadeh5731
2 ай бұрын
Thanks
@mahmoudnaser453
3 ай бұрын
hello Mr tevs,I, didn't see your for long time, where are you, may be you go to travel or you leave your house ,or something else ,so are you ok or something wrong?I hope you're good health,but I have a question,are you from maylasi,or Singapore or in the area of nearest,
@tevzTVTevatronics
3 ай бұрын
I'm just busy with the repairs. I am from the Philipines.
@prabhuprabhu4274
3 ай бұрын
Nice
@hasantamer9199
3 ай бұрын
good
@bobanmanic1235
3 ай бұрын
Thanks a lot for the video.👍
@praveenmurkar743
3 күн бұрын
Dear sir lg ,32LH602D-TD led tv not switching on.power supply showing only 7 dc voltage.
@aungzawoo9926
3 ай бұрын
❤❤❤❤❤❤❤
@ZafarIqbal-qy9qe
3 ай бұрын
❤❤❤❤❤❤❤
@mohmmedmjij7371
Ай бұрын
سيدي أنت رجل عظم بتوفيق
@robinsonsoto8471
3 ай бұрын
Can you provide more information on the instalation of the Strw6053n.
@SoyapiChirwa
2 ай бұрын
What is the no of control ic you replaced with str w6053? Chirwa s Zambia .
@pak_guru_toro
3 ай бұрын
Awesome modification
@tevzTVTevatronics
3 ай бұрын
Thanks
@damochannel1752
3 ай бұрын
Sir san po kayo located
@tevzTVTevatronics
3 ай бұрын
laoag city
@darfor12
3 ай бұрын
Thankyou about this informations
@NorlysHernandez
3 ай бұрын
nice repair master as always
@tevzTVTevatronics
3 ай бұрын
Thanks 👍
@bshi0288
3 ай бұрын
Thank you very much for your video uploading.By the way, it is possible to cutoff end of solder suker with small scissor,And It will make you to use your solder suker without detach soldering tip from pad as you did in your video (4:50-5:10)
@bineshchauhan8713
3 ай бұрын
Thanks sir Please give small diagrqm of new modification on paper for screen shot, so new lerner understand and imove them work
@PasinduDilshan-we7so
3 ай бұрын
Wow 😮
@electronicrepairservice2020
3 ай бұрын
Awesome modification, excellent repair! Yes, videos do take a long time to produce, I have some from 6 months ago that I haven't edited yet. It's hard to do both - work and edit videos.
@payusavisit3482
3 ай бұрын
Very useful and éducative conversion 🎉
@gabrielcuevas5837
3 ай бұрын
Saludos amigo.
@yuliantoanto3884
3 ай бұрын
Terima kasih sudah berbagi ilmunya
@olisesundaynduka3689
2 ай бұрын
Excellent as usual Master. God bless sir
@heikobarisch3235
3 ай бұрын
Respekt Mega ein IC rettet einen kompletten Fernseher. Dankeschön für das lehrreiche Video. LG.Heiko
@JoeCentralTech
3 ай бұрын
Like always nice work
@jerrythabo9045
3 ай бұрын
Thanks Mr Tevz your videos are the best ❤
@dominggobautista3468
3 ай бұрын
Thanks sir
@tevzTVTevatronics
3 ай бұрын
Welcome
@ssee9130
3 ай бұрын
Very interesting thank you 🎉
@rajeshjadav1240
3 ай бұрын
Nice. ❤
@tevzTVTevatronics
3 ай бұрын
Thanks 😄
@leevan1424
3 ай бұрын
good job thanks
@bshi0288
3 ай бұрын
I have 29 inch LG CRT TV which did not display any screen at all. When I plugged in its AC cable I measured DC voltage of B+ filter capacitor(160v 100uf), it measured 38Vdc with DMM. But as soon as I click power switch,It suddenly soared to 120v and gradually decreased until it reach 38Vdc. And I also measured pin #9 of STR-S6707 in the HOT area with analog meter and it also soared to 7.3-7.5 Vdc as soon as I click power switch, and gradually decreased until it reach 6.4Vdc. I purchased another STR-S6707 and replaced primary STR-S6707 with it by soldering but that would not fix this voltage decreasing problems.. Would you give me a clue What cause this symptom of decreasing voltage of B+ filter capacitor and VCC of switching ragulator?
@tevzTVTevatronics
3 ай бұрын
Some power supply goes to a lower voltage when the system is in standby mode. try press the channel up or down or other power booton. Check also the 5 volts standby.
@ruwanrathnayaka7782
20 күн бұрын
Thank you sir❤
@emilioemilio1710
3 ай бұрын
Muchas gracias por compartir!!!
@dominggobautista3468
3 ай бұрын
Thanks sir
@reydungan567
Ай бұрын
Sir san location niu?sony 55 inch.6 blinks.model kd-55x7000e
@tevzTVTevatronics
Ай бұрын
laoag city
@jaym5938
3 ай бұрын
Why using the STR-W6000S so much? It seems a bit of a pain having to jerry-rig it. Is it a lot cheaper?
@tevzTVTevatronics
3 ай бұрын
This TV is cheap, could you let me know what you want to replace it? a power supply that is more expensive than the tv?
@Junior-ff7ee
3 ай бұрын
Hie some of your videos you did not put str on heat sink why or am wrong?also may you do a video of modification of a double mosfet power supply ?
@tevzTVTevatronics
3 ай бұрын
Ill try.
@mahmoudnaser453
3 ай бұрын
may be????????
@deejayrahman
3 ай бұрын
Sir!!are just good when it comes to electronics..am soo lucky I found ur channel cos am really learning alot from you
@tevzTVTevatronics
3 ай бұрын
Thanks and welcome
@johnluisborja6480
3 ай бұрын
Spokining dollar pla toh c master wla akong mpupulot d2 bye😂
@krasag
3 ай бұрын
Полезен видеоканал да специалисти в ремонта на радиоелектрониката
@karanahuja6302
3 ай бұрын
Your repairing videos are excellent and your camera quality is awesome. 😊😊
@tevzTVTevatronics
3 ай бұрын
Thank you very much!
@Nosan얼음속붕어
3 ай бұрын
한국의 동부대우전자 TV L43S6550BK 같은 보드입니다!
@tevzTVTevatronics
3 ай бұрын
Im not sure
@ifeoluwaomoyeni
3 ай бұрын
Thanks for sharing🎉🎉
@FSX3000
3 ай бұрын
how the hell do you just know what mosfet to replace with and how to connect it ? how did you learn these things
@tevzTVTevatronics
3 ай бұрын
We can learn from our experiences and knowledge. Even Chimpanzees are capable of innovation. They can come up with new ways to solve problems, such as using a stick to reach termites out of a mound.
@aminulvivo1420
3 ай бұрын
Good video sir 🌹
@noureddinecherradi5037
3 ай бұрын
Good work thanks
@priyanshirajshivanshiraj5044
3 ай бұрын
Good job sir
@michaelngobeni5640
3 ай бұрын
Do you sell smd components
@tevzTVTevatronics
3 ай бұрын
No
@sultanrasulhanow6690
3 ай бұрын
👍
@shalenprasad1342
3 ай бұрын
Very nice video sir thanks 😊
@tevzTVTevatronics
3 ай бұрын
Most welcome
@bshi0288
3 ай бұрын
Thank very mcuh for reply! I plugged in AC cable and checked DC voltage of AT24C04 IC which seems to be eeprom for this 29 inch LG CRT TV.I placed red probe to pin #8 of AT24C04 and black probe to pin #4.It measured 5.084Vdc regardless of clicking power switch.I also pressed channel button and other button on the remote controller But It won't make LG 29 inch CRT TV to display any screen at all...
@tevzTVTevatronics
3 ай бұрын
try hang the eeprom
@bshi0288
3 ай бұрын
@@tevzTVTevatronics What is meaning of hang the eeprom? dose it means to replace AT24C04 IC with new IC?
@tevzTVTevatronics
3 ай бұрын
@@bshi0288 just hang it and try it, if the tv turns on it? it means it is in standby mode. or it has an EEPROM program issue. Check if you have a remote try to remote it, but resolder back the EEPROM before you remote it.
@bshi0288
3 ай бұрын
@@tevzTVTevatronicsI resolderd all pin of EEPROM(AT24C04) on the bottom of PCB and I repeated to plug in AC cable and push power button on the remote and unplug AC cable, more than ten times. I noticed that whenever I push power button on the remote,DC voltage of B+ filter capacitor(160v 100uf) suddenly became 120Vdc and it gradually decreased until it reach 38Vdc.But Unfortunately, No matter how repeat plug in, push power button and plug off,It won't display any screen at all
@bshi0288
2 ай бұрын
A few days ago, I noticed that there is no faulty in the HOT area. So I doubted maybe there was loose contact on the pin of IC,Beacuse This CRT TV was manufactured over 25 years,So solder joint would not as tight as twenty five years ago. And it seems that weight of its PCB is about 2kg,I think that Whenever I deposited this heavy PCB on the floor,this would put pressure on the pin of IC.So there would be minor crack on its solder joint. I soldered all pin of LG8708-08A, GL3812,TB1231N and Turner TUSHB-A07A at the bottom of PCB, and It finally displayed screen! In fact, I have another CRT TV(LG slim 21fu1r-ns of 220 voltage) which was not able to display any screen.So I did IN CIRCUIT Testing all of capacitor with ESR meter. I found a capacitor which has no ESR and capacitance value at all, It was connected to horizontal coil(250v 1uf). So I replaced this capacitor and other capacitor which is located in the vicinty of FBT(250v 4.7uf) and in the vicinty of Vertical Deflection Booster(STV9326)(35V 100uf) which has somewhat higher ESR value,So I also replaced these capacitor,too. After replacing three capacitor,It finally succeeded to display a screen,But,the screen was very bright and It displayed lines across the screen . Worst of all, IT IS NOT ABLE TO CONTROL BRIGHTNESS with screen adjust potentiometer on the lower FBT... Besides I heard a weird static sound near CRT anode cap whenever I turn off this 21fu1r-ns CRT TV I really want to control brightness with screen adjust potentiometer on the lower FBT and get rid of weird static sound. I really very much appreciate you if there is workaround to repair these problem.
@esilvap26
3 ай бұрын
Lightning damage.
@tevzTVTevatronics
3 ай бұрын
I think so
@shaik5336
3 ай бұрын
I'm the first like and comment ❤
@sunsys0
3 ай бұрын
#important
@tevzTVTevatronics
3 ай бұрын
Indeed
@mahmoudnaser453
3 ай бұрын
the board I think it's built with digital reiciver
@tevzTVTevatronics
3 ай бұрын
No, It is not.
@shafiahmad6795
3 ай бұрын
I am your subscriber and also give like to your each and every video that you upload
@tevzTVTevatronics
3 ай бұрын
thanks
@preston963
3 ай бұрын
Dodgy as fark!... Not impressed!... Been a tech 40+yr.
Пікірлер: 113