Fantastic..I really could do with one of those right now..Greetings from England.
@irishguy200007
5 жыл бұрын
I love real engineers. No crapy music, no long self promotional intro and a simple but super effective device.
@andezbox
5 жыл бұрын
cumon mate . A hard core engineer would have Kraftwerk going on in the back ground .
@parvizos5264
8 жыл бұрын
Hi buddy I am sure you are a genius and I just want to thank you for your useful ideas . keep up the good work !!!
@paulmeynell8866
Жыл бұрын
I’m assuming it’s fine to bent cold when I googled bending threaded bar it said heat it up , then I found your excellent video.
@c2757
2 ай бұрын
On the other hand, when the U bolt you bent cold is holding the bodywork onto the chassis of a bus with 30 people riding on it, you might want to feel comfortable that the bolt ain't going to break due to stress locked in due to being bent up cold.
@mostlymoparih5682
8 жыл бұрын
You pack a lot of stuff into a little space. Are those baby jars attached to the bottom of those shelves. TFS
@littlebrother256
8 жыл бұрын
yes. there are actually about 50 baby jars attached to the bottom of the shelve. all organized with differnt fasteners.
@mostlymoparih5682
8 жыл бұрын
That's making the most of the space that you have. Good deal. TFS
@brettgrassam9819
2 жыл бұрын
What is the calculation for the curve in the handle? I would like to try and make one for myself , I can see that the curve of the handle is critical as it will h Keep the handle holder wheel in the correct arc around the bend wheel. Am I thinking about this correctly or over thinking it?
@CarlPugh
4 жыл бұрын
Great video! Have you tried to bend threaded stainless steel rods? I need to bend 1/4”
@zanelile8192
4 жыл бұрын
Will these work for spring hangers for an old car ?
@bigtanksc
6 жыл бұрын
Nice
@KenJamesJr
4 жыл бұрын
You're a genius Bro. Periodt.
@arguingwithstupidpeople2047
5 жыл бұрын
You are one creative fellow.
@russg1801
7 жыл бұрын
OK, where did you get the wheels?
@rudy1574
2 жыл бұрын
Lets see you do a square bend ????
@kylemartin3454
5 жыл бұрын
Great tool!!! Where are you located? :) I need 12 custom u-bolts and everyone is quoting 4 weeks
@rahalati
4 жыл бұрын
Great tool. Can you use it to bend none-threaded rods? If not, how to modify it to do so
@68giraldo
3 жыл бұрын
very good job. I have a question you have videos of how to ace those same but squad
@andezbox
5 жыл бұрын
Sir, I envy the organisation of your shop ! and thanks for this tip ! Save you $5 makin a u bolt .
@68giraldo
3 жыл бұрын
very good job. I have a question you have videos of how to do those same but squad
@shainnahid9994
4 жыл бұрын
Ur super duper hero how to make this lpz help me
@E-commerceassociation
7 жыл бұрын
what rod do you use to make bolts?
@adamgeiger4990
4 жыл бұрын
Nice Machine, Good Job
@michaelbabatunde3915
3 жыл бұрын
Very good innovation
@ИршатИршат-у7о
3 жыл бұрын
Молодец англечанин
@jonnyjohnson7869
7 жыл бұрын
Can you tell me what kind of wheels you are using for this? Also measurements for the height of the first wheel from the floor of the bender and the distance to the wheel on the handle from the center of the first wheel hole?
@littlebrother256
7 жыл бұрын
Jonny Johnson I am using a concave wheel aprox 2 inch diameter x 3/4 width with 1/4 bore. First wheel is approximate 1.5 inches from the base ( stationery wheel) . Between the two wheels 2 9/16 inches. Make sure you have a curvature on the handle. When inserting the threade rod it has to clear the 2 wheel in the opening position. It does not matter wheel size. wheel size determine the width of your U bolt. This wheel 2 inch will give you 2 1/8 inch u bolt center to center .
@littlebrother256
7 жыл бұрын
Jonny Johnson Those measurement fror the base wheel and the distance between the wheels are center to center.
@jonnyjohnson7869
7 жыл бұрын
Fantastic what is the wheel made of polyurethane? And where did you get it?
@littlebrother256
7 жыл бұрын
Jonny Johnson Yes polyurethane I am not sure wher I purchase them.
Пікірлер: 34