Absolutely awesome. I just started working on a quad bicycle hobby project and this video has been a good introduction to DIY steering systems. So thanks, man.
@bvisel4558
5 жыл бұрын
Read about bump steer, the tie rods should be on the same plane as the control arms. also read about Ackerman angle.
@joseantoniozarzosa7805
2 жыл бұрын
Great build I'll get the concepts and downsize to match my project. Thanks
@muddymuddymuddmann
5 жыл бұрын
I hate negative comments and criticism. But constructive criticism is exquisite. But even more precious is the applause. If you chastise a fool, He will hate you. But if you chastise a wise man, He will thank you. I watched the 3 wheel Baotian 50 cc series. I loved watching the high speed editing, and the amount of work that you put into the project. and the time you took for detail filmed and edited. You left nothing out. I call that hard work. And I call it a polished production fit to watch. Read the comments with constructive criticism, and thank them. They are worth more than silver. And I'll enjoy watching your channel grow. I look forward to more videos. MUDDy
@IsraelMendoza-qc9zj
Жыл бұрын
Really impressive I'm trying to build a go cart And this would make an excellent front suspension Thank you Saludos desde Culiacán Sinaloa México
@majan7083
5 жыл бұрын
Nesviđa mi se što je širok a mozda i pre nizak ali sve u svemu odlican projekt svaka čast!
@DShomemade
5 жыл бұрын
Hvala puno ;)
@Adrian-jo2dz
5 жыл бұрын
Odličan projekt! Volio bih da je što više ovakvih projekata!☺
@DShomemade
5 жыл бұрын
hvala puno ;)
@atagbababa6423
5 жыл бұрын
Nice brt i dobro si se ošišao
@DShomemade
5 жыл бұрын
hehhehe hvala tiii
@markomijanovic8171
5 жыл бұрын
Svaka čast na urađenom poslu. Mali savet uzmi i ugradi disk kočnice i malo oko upravljača sredi to bolje neki sistem. To je sve što sam naveo savet da ne bude posle nešto loše...
@DShomemade
5 жыл бұрын
Hvala ti punooo
@williamickes3143
7 ай бұрын
I'm building a cross cart to dirt drag with. If you lived any closer you would be building another. 👍👍🏍 Good work.
@yachtsteve
5 жыл бұрын
Love how your dogs are TOTALLY into the build
@adilsabotic572
5 жыл бұрын
Odlican projekat samo nastavi sa epizodama
@DShomemade
5 жыл бұрын
@Mario-th1et
5 жыл бұрын
Dobro si napravio,ali po meni je presirok i nizak prednji deo,stavi vece tockove itd...
@DShomemade
5 жыл бұрын
da malo je siroko hahahah
@КошмарКошмар-й2б
5 жыл бұрын
Бро круто получилось, продолжай дальше проект👍👍👍💪💪💪👏👏👏
@bobanbobi7096
5 жыл бұрын
To se cekalooo!!!!! BRAVOO
@DShomemade
5 жыл бұрын
@CHILLRIDERtv
5 жыл бұрын
Nice work bro. Mind if i ask what kind of weld machine do you use? Thanks for sharing.
@milosevicmotors3572
5 жыл бұрын
Najbolji si svaki tvoj video sam pogledao kralju 💪
@DShomemade
5 жыл бұрын
Hvala puno
@nonarrativeboxingnunn9856
Жыл бұрын
Thank You, DDS!
@lukazilic7187
5 жыл бұрын
Bravo care imas dobre ideje😉
@DShomemade
5 жыл бұрын
Hvala tiii
@kulinraval4755
2 жыл бұрын
Thank You For making us understand this simple and very easy way to build go kart mainly steering wheel movement is very easily constructed by you but I want to know hold end ball joint Bolt and nut resist in jerks as it's loosen up with jerking so is there any solution for it thank you
@comadg9922
5 жыл бұрын
Dobar je ali je širok . Svaka ti cast
@DShomemade
5 жыл бұрын
da sirok je dost
@markojerkic1210
5 жыл бұрын
dosta je siroko a pre tanki su ti tockovi, stavi neke deblje tockove pa ce bit dobro
@jasonb4350
4 жыл бұрын
You are very creative! But the steering will break very quickly, you need to make stronger tie rod ends and use thicker rods.
@jasondeselles3471
5 жыл бұрын
First 18:00 I thought this guy was building a badass dune buggy. Last 4:00 I realized he's building a third-world Segway.
@Ashishkumar-re6rs
4 жыл бұрын
Nicely presented and helpful info
@klownskull702
5 жыл бұрын
how long did it take to break your "tie rods"?
@mata133
5 жыл бұрын
Bravo samo nastavi
@DShomemade
5 жыл бұрын
Hvala tiii ;)
@gordu4652
5 жыл бұрын
dobar si mali, dobar, kao za pocetak si super... za jedno 2-3 god. ocekujem da sve ovo usavrsis i pocnes da prodajes vrhunske bagije
@AsadAli-yw5kt
5 жыл бұрын
nice work i love ur hard work i easly understand ur method thanks for it...
Beste Wünsche für weitere kreative technische Entwicklung. Kroatien ist stets überraschend inspirationsvoll ein schönes Land und auch alle Kroaten sehr menschenfreundlich und pfiffig, wie hier bei der Veranschaung zu bewundern ist. Bravo. Pozdrowienia z najlepszymi życzeniami sukcesów dla tak uzdolnionego pasjonata: z Berlina i Krakowa (PL)
@peteaddis1548
5 жыл бұрын
This is a death trap and a waste of good metal!. You will suffer from an enormous amount of bump steer, toe in and toe out,when ever your suspension moves up and down!...
@edvanthienen6769
5 жыл бұрын
For a young Man with the obvious Skill and Know-How to do it RIGHT you are Rushing through a job that requires care and attention to detail you slapped together welds that will no doubt break on the first good bump for no reason other than speeding through this, and like Bob said below use the well-known front-end Ackermann and Bumsteer calculations to set it up right. Also your suspension height and shock setup needs attention. I feel you were showing off a bit to much and hurting your project in the process! But that's just my observation and I'm just an old dutch guy from Canada!
@filename3094
5 жыл бұрын
Congratulations on a new world record for high speed cart building.
@stitchem7
3 жыл бұрын
You are braver than I, sir.
@sudrajatsuhaeli6799
5 жыл бұрын
Good job, you must be a hard working person. Very creative. Someday, your design must be registered for intellectual property.
@adrianbojlovcic2844
5 жыл бұрын
Odlican projekat i kaja ce maslina da bude
@DShomemade
5 жыл бұрын
E to se jos nezna hahah
@markobulic1590
5 жыл бұрын
Bravo kralju
@DShomemade
5 жыл бұрын
Hvala puno
@jack-j6167
5 жыл бұрын
Hey man can you maybe pls send the measurements of the suspension pls... I have a Project that i like to start and would like to know the measurements.... thx.
@arvidas3437
3 жыл бұрын
I wonder if he finished it
@brankoandrasic890
5 жыл бұрын
koliko ti traje ona žica za varenje kad si prvi put stavio rekao si 15 kg koliko imaš sad i jeli se brzo troši
@DShomemade
5 жыл бұрын
Ma jos je imam pola hahhahah Bas dugoo traje, jer je najveci namotaj ;) 15kg.
@oussamayahyaoui9300
5 жыл бұрын
@@DShomemade oussama yahyaoui
@ilalgopro283
5 жыл бұрын
Love this vedeo
@markomarkelic5720
5 жыл бұрын
Ja sad igram igricu na mobitelu i dođe mi obavjest "novo s kanala doctor d.s.".Ja reko jeb ti igricu idem ja gledat DOKTORA. Pozdrav iz Bribira!!
@DShomemade
5 жыл бұрын
hehehheheh brat mojj
@elcreador6675
5 жыл бұрын
Excelente 🇩🇴🇩🇴🌎
@hadefyacine998
4 жыл бұрын
Thank you very much for the information that you can give me planning and accounts in order to make it like this
@dominikkuhar4226
5 жыл бұрын
Odlicno
@DShomemade
5 жыл бұрын
Hvala puno
@dedesutiawanchannel8780
3 жыл бұрын
Nice job doc. Kereeennn
@mattworthington4373
5 жыл бұрын
Sort of wide no?
@ByDemonsBeDriven
3 жыл бұрын
Odlična ideja! Samo za pristoje vozne karakteristike treba masovno doradit koncept, pogovo u ovjesu i šasiji.
@DPRDewanPangkasRambut
5 жыл бұрын
Spectaculer nice job3 friend i like
@eduardojerez695
5 жыл бұрын
GOOD MY FRIEND,TRICICLE VERY COOL
@joelacosta8275
4 жыл бұрын
bien ahi gracias x deleitarme un poco con las ideas
@eimadaboshivan7209
5 жыл бұрын
Very clever and creative I wish you success my friend
@onosgwill7696
3 жыл бұрын
Hey I am so amazed with what you deed. Please Can it be possible for you too tell me what kind of materials you used e.g size of crew, nuts, pipe, how many mm is the flat metals. And the names of the materials you used, thanks
@jayaborbanyu9486
5 жыл бұрын
great great ... go on
@t-art2780
5 жыл бұрын
Thank a lot...🙏🙏🙏🙏
@vojinstojadinovic9114
5 жыл бұрын
Uzmi od lima za spoljni izgled neka stara sedišta i probaj da napraviš svoj auto i marka neka se zove SDS super doctor s 😂😂😂😂
@DShomemade
5 жыл бұрын
hahahhah budem hahahha
@oremiljic5808
5 жыл бұрын
Koji motor stavljasu na to Ekstra je sve jel to nova masina??
@DShomemade
5 жыл бұрын
To je masina od boatinia 50cc 4t... Ali probat cu stavit nest bolje ;)
@oremiljic5808
5 жыл бұрын
Stavi motor od auta 1200ccm
@xannyanthonymoisesaraujofi2835
3 жыл бұрын
Hello friend, I wanted to know if you have the exact measurements or an average of the buggy or do you know where I can get them, it would be very helpful.
@sunhuatom
2 жыл бұрын
the turning angle of both wheels will be the same, would wheel slippery be a issue for GO KART?
@blitzgamer9386
5 жыл бұрын
Super je video.😎😎😎👏👏👏🙏🙏
@DShomemade
5 жыл бұрын
Hvala puno
@pisig98b
4 жыл бұрын
why is that lower control arm rigid? shouldnt it be pivoting like the upper? it will be like having no suspension at all! good workmanship though
@techworksinfo
3 жыл бұрын
Good work
@Kojic966
5 жыл бұрын
Huuuu bracaaa.. Samo jaci motor.. I ima da kida..
@DShomemade
5 жыл бұрын
hehehh da daa brt
@Kojic966
5 жыл бұрын
@@DShomemade A msm da li bilo sa motorom.. Na pedale ili se guralo rucno.. Kada ti napravis mora da valja..
@DShomemade
5 жыл бұрын
@@Kojic966 hahhahah xd da daa
@marlonpublico8325
4 жыл бұрын
nice work sir..
@holnesrashad9759
4 жыл бұрын
i wish i was that skilled i like it u inspired mr to try
@bhupendradesai3402
5 жыл бұрын
Nice but u not show scale of each part. Please show it. Very nice please reply
@hilmanrgsasenen2155
5 жыл бұрын
Super build
@seamanss3433
5 жыл бұрын
Awesome 🇹🇷
@engtranhiep
3 жыл бұрын
good job men
@momentoelectrico4323
Жыл бұрын
what wheels did you use?
@yongyuthmeemuang
3 жыл бұрын
very good❤️
@Sultan_Z
3 жыл бұрын
Amazing
@p.wikary9435
4 жыл бұрын
kingpin and steering are life-threatening ................good luck
@ameerpasha9297
3 жыл бұрын
Very good
@provazi7047
5 жыл бұрын
Predobro je samo jako volio bih te posjetiti ali sam daleko iz Bosne sam
@DShomemade
5 жыл бұрын
Hvala punooo pozz brt
@peky2560
5 жыл бұрын
buraz sve je super samo da je malo uze
@mannyways
3 жыл бұрын
Nice work, Great JOB!
@mahindranag
5 жыл бұрын
excellent work man , what about with 3 feet width cart, is it same.
@ivanbaric483
3 жыл бұрын
da dobro-super
@ATAYA532
5 жыл бұрын
بسم الله الرحمن الرحيم. ما شاء الله
@jorgecastillocobenas553
2 жыл бұрын
Hello friend, thanks for your information, greetings from Peru, I am going to make a wheelchair with a motor in each wheel, what idea do you give me?
@u.pstarledlights9829
5 жыл бұрын
Good job sair
@stasguobrhawomwdtml2660
5 жыл бұрын
excellent
@samuelclark4525
4 жыл бұрын
Roads in my area aren't exactly the smoothest. Welding in a suspension with my powerarc is pretty much mandatory.
@mai_mai_yeu_em
4 жыл бұрын
I don’t see you driving it maybe it not working 😂😂😂
@KruChuan
5 жыл бұрын
Thank you.
@g.p.5225
5 жыл бұрын
top!
@tvt5097
5 жыл бұрын
Jesi prodo onaj drugi karting
@witosarlaw
3 жыл бұрын
Mantap bang... saya juga bikin mobil mini dari motor...😊👍
@Manehoph
5 жыл бұрын
Love your video men
@vinnyvega1985
5 жыл бұрын
What in the methanphetamine is this?
@ilicicdarijan2018
5 жыл бұрын
Bolje bi bilo da donju osovinu koja drzi amortizer pomeris vise ka unutrasnjosti trocikla samim tim ces dobiti bolju amortizaciju i veci klirens...
@DShomemade
5 жыл бұрын
ahaa ahaaa hvala na savijetu
@miroslavvfilipovicc9162
5 жыл бұрын
Dobar samo tako 👍👍👍👍👋
@DShomemade
5 жыл бұрын
Hvala punoo
@miroslavvfilipovicc9162
5 жыл бұрын
@@DShomemade uvek 👍👍👍😉👋
@StupidEarthlings
4 жыл бұрын
Calling it at 11 min,.. the shocks are waaaaay too angled to even slightly function. I assume we'll see that unfold later. So, you cant even guess at this point? Been doin it awhile..
@vatreniyt4654
5 жыл бұрын
Eksta je jel ces nastaviti to vozilo sto si poceo da rafis da ga zavrsis
@DShomemade
5 жыл бұрын
da daaaa
@jamescleave7024
4 жыл бұрын
GO KART? With this size, thickness and weight, looks more like a tank suspension...
@paswedacars7921
2 жыл бұрын
Same observation. It will so heavy. Again where the suspension arm has been welded to the frame will be a point of weakness if am not wrong.
Пікірлер: 304