What kind of wood are you using and what glue are you using boss..
@nabru5612
4 жыл бұрын
nice vid
@rb3166
4 жыл бұрын
Nicely done, but back in 1984 we only had the jigsaw and the rest was done by hand! Oh I had a "cheesegrater" hand tool for bevelling before the sanding....... Oh yeah I also used a router drill bit sometimes to help with the bevel.....
@doruksimsek3636
3 жыл бұрын
why do old people always have to tell things about how they use to do stuff 🤣
@diyresttube
3 жыл бұрын
nice work bro.
@captivatingcateel3307
3 жыл бұрын
Did you add a roundover to both sides of the plywood? Or just the front side?
@makeitall3898
3 жыл бұрын
Just the top of the board in this video, but we have experimented with diffrent method. Once we tried a small round over on the bottom and a larger round over on the top that met in the middle. That worked well, but it didn't make a huge difference. I'd say the only thing to watch out for is making the bottom edge too sharp, but that can be adjusted with sanding at anytime.
@philippemaitre8177
Ай бұрын
What type of wood do you use???
@avoznodeserto-cm4wz
3 жыл бұрын
Brasil
@xav732
3 жыл бұрын
did you make it out of birch ply or fir?
@AKALizxrd
3 жыл бұрын
In 6ft tall and 130 pounds, what size skimboard measurements would be best for me?
@makeitall3898
3 жыл бұрын
In my experince different sizes can achieve diffrent levels of stability, but you can learn and have fun on just about any size. That being said I'm not a pro skimboarder, and I would recommend looking else where if you wnat the ideal recommended size.
@daveanthonylat-ay796
3 жыл бұрын
Pahingi naman ng skim board idol 🥺
@irfanmaulana4169
3 жыл бұрын
How mny cm is the plywood
@makeitall3898
3 жыл бұрын
1/2 inch, so 1.27 cm. We did this because the only widely avaible cheap option in out area was either 1/4 inch or 1/2 inch. I haven't got the chance to try but it might work better to go slightly less than 1/2 inch, but I think 1/4 too thin.
@audreylefever8500
3 жыл бұрын
qu'elle est l'essence de votre bois svp ? merci
@Asgard_TG
2 ай бұрын
3:13 what is the liquid you use bro ?
@matthewsharpe366
9 күн бұрын
Diluted bird shit
@rb3166
4 жыл бұрын
No varnish or resin?
@makeitall3898
4 жыл бұрын
R B we used an old water based varnish, considered using resin but not really in our budget :)
@rb3166
4 жыл бұрын
@@makeitall3898 Back in 1984 resin was $5.99 a quart! What happened? :)
@avoznodeserto-cm4wz
3 жыл бұрын
quero comprar uma como faço?
@DC140495
4 жыл бұрын
hi, were have you found the desing with the measures?
@makeitall3898
4 жыл бұрын
Sorry to say that I drew the design by hand so I can't give you a pdf or anything. If you're truely intrested in the dimensions I could email you a photo with some measurements next to it. Also the method I used to draw the design was pretty simple: I folded a piece of paper in half and lightly skethed the curves until I found a shape I liked. Then I traced the sketch with a darker stroke, cut it out, and traced that onto the board. After that I cut one half of the board, and just to be thorough, I used the cutoff to trace the other side so it was perfectly symmetrical. Obviously, that is a pretty involved process, but it was worth it for the first board. ( I used it as a templet to make several others boards of the same dimmensions)
@kilowazukerberg3762
3 жыл бұрын
Email me the photo and measurement
@doruksimsek3636
3 жыл бұрын
I wouldn't email you shit, you gotta ask for it's called manners.
Пікірлер: 30