Excellent machine!!! One Caveat: you should always measure runout at the actual machine center, instead of the outside of the chuck. The outside is almost never square to the inside bore. chuck up a piece of drill rod or some precision round bar, and use that to measure runout.
@dutchsailor6620
Жыл бұрын
If your machining skills match your welding skills then watch your fingers. Try using some more shielding gas in the future.
@elyapm3520
Жыл бұрын
My dear brother, if you increase the welding shielding gas a little, it will be a healthier work..! Otherwise, overloading may break your machine! Respects..
@johnkoury1116
2 жыл бұрын
Excellent machine as well as music!!
@user-xq3xg2tj5h
3 жыл бұрын
대단하십니다 .대박나세요.
@user-gw3fd5zw8n
2 жыл бұрын
감사합니다. 님도 대박나세요
@user-zx9il5et4r
3 жыл бұрын
용접하는거나, 만드는 폼새를 보니, 진짜 개판이네! 정성과 섬세함과 정교함이란 찾아볼수가 없네요! 그 좋고 편한 논가스 용접기로 용접 하는것도, 마치 귀찮아서 막가파식으로 용접하고, 철판을 붙이는 것도 진짜 DIY같지도 않네요! 이렇게 유튜브로 내보낼꺼면, 시청자들이 볼때도, 덕이 되야하는데, 보는 내내 짜증이 나오고, 한숨만 나오네요!
lessons from long journey 1)draw a specific blueprint even each and every bolt and nut 2)before cutting and welding, you have to make a realistic wooden mock-up sample 3)ever step, measure and measure.
@MISTERX-cy8vh
2 жыл бұрын
what is the width of the machine guide?
@user-dl1te2pf2d
Жыл бұрын
Хорошо. Но временами такое ощущение, что надо добавить расход CO2 при сварке 😁
@QWireArt
2 жыл бұрын
Струбцины называются ваймы. Логичнее профиль располагать на ребро, чтобы меньше прогиб был.Фиксацию ответной каретки проще делать без резьбы, поднял-опустил, можно с пружинкой или просто с фиксацией штыря, в крайнем верхнем положении, чтобы не терялся. Когда сохнет клей времени крутить винты нет.
@colmgrehan8858
2 жыл бұрын
We here call that weld style bird poo
@budipirang2694
Жыл бұрын
Very nice
@dalejustice9207
Жыл бұрын
What size motor is that? Also what are the parts called that look like collars?
@unnajayachannel6921
2 жыл бұрын
Good 👍👍 amazing
@water9062
2 жыл бұрын
做得好👍
@user-mi6ub7gy4b
2 жыл бұрын
독특한 취미를 가지신분 이네요 조만간 터미네이터도 만들어 내실듯
@user-gw3fd5zw8n
2 жыл бұрын
먹방 뷰티방 일색의 한국유튜브계에 큰돌을던져 파문을 만들어보겠습니다 감사합니다
@user-gw3fd5zw8n
2 жыл бұрын
@@user-uu9bg3gh 땡슬랏!
@davidcrawford6505
Жыл бұрын
With those gnarly welds, I see this thing blowing apart if pushed too far. Careful.
@AJ........
2 ай бұрын
My thoughts exactly. One probably shouldn't attempt a machine like this before they learn how to weld. It could be extremely dangerous
@oluka9002
9 ай бұрын
nice
@2afather
Жыл бұрын
안녕하세요 혹시 모터 뭐 쓰셨는지 알수있을까요?
@hmingdailovakhiangtehmingt7464
2 жыл бұрын
Spark wellding light off
@user-dl2do9ff8w
Жыл бұрын
부속 구입은 어디서 하나요? 문외한 사람인데 해보고 싶네요 부속 명칭 용어도 모르고 어디서 구입 할까요
Пікірлер: 72