Please don't let your dog take the camera, use a human next time!
@davidbarnes479
9 жыл бұрын
do you have a part 3 to putting back together I can't get my 300 to engage the gear will shift but bike won't move
@davidbarnes479
9 жыл бұрын
do you have a part 3 to putting back together I can't get my 300 to engage the gear will shift but bike won't move
@guysoileau8606
4 жыл бұрын
Sounds like your thread descriptions are backwards, right hand thread tightens to the right loosens to left, left hand thread tightens to the left loosens to right.
@kaleosantos6313
4 жыл бұрын
I NEED HELP. I HAVE A 1990 honda fourtrax 300 and the clutch kick start side was leaking oil so i just took the pan off and all that stuff fell out like u said and a friend of mine took that kick start gear from the rear n hooked the hook n just pushed it in n he said that's how it goes but on urs it looks like u wind the spring up then the tab aits in between those 2 levers. So when I did it his way n started it it made that clicking noise. I turned it off and winded the spring to make it like urs and now no noise but I don't have any forward or reverse gears at all. All cuz of a oil leak. Will someone PLEASE. HELP. ME. FIGURE. OUT. WHAT. HAPPENED......... PLEASE. 😔
@davalleyguy5020
4 ай бұрын
The part of the video just before you remove the basket nut, can't see it. Is that an ear you were prying open to be able to turn the nut
@aaaa1953
6 жыл бұрын
The front clutch is a left hand thread, loosens clockwise, other clutch is right hand thread and loosens turning it anticlockwise.
@skunkmonkey2010
8 жыл бұрын
you need to ge a better camera man
@Solitude313
8 жыл бұрын
+Cool Breeze Hes been fired.
@LexannasSoaps
2 жыл бұрын
What is the point of that lever on the secondary clutch can you take it off and leave it off , because I don't want to have to take the engine off frame. And I was wondering if you could leave it off
@ryanglidden9551
5 жыл бұрын
When I change my secondary clutch pack is the anything else I should do while I'm in there. It seem to be slipping in higher gears and I would hear a clunk once in awhile going up Jul in 3rd or higher. Is that normal? Any info would be good haven't work on these wet clutch systems before.
@Fl_bluecollar
6 жыл бұрын
Also do you have a video of the reinstall of the one way bearing? Before I replaced the timing chain my kickstarter worked perfectly, now it seems to just free spin, I’ve referenced my Honda shop manual but it doesn’t have the greatest pictures
@dosstheboss100
8 жыл бұрын
I'm working on a 350d everything looks the same on mine except the tensioner guides i have a little black washer that I didn't see where it came from i believe it goes behind the tensioner guide just like yours except mine bolts on the left side does this sound right
@garycourt8593
5 жыл бұрын
Very well done, Thanks, would appreciate a reinstalling video and a little more on the upgrades you did on the motor. I'm not a dirt racer but would like to know more on what you guys do to make it stronger.
@alexdahms5182
4 жыл бұрын
How do you reinstall the cover?
@jasonvandervort4904
4 жыл бұрын
looking for a video on a 2004 suzuki eiger wet clutch replacement
@tylerstansfield9569
8 жыл бұрын
do i need to torque anything when i put it back together?
@Solitude313
8 жыл бұрын
Only if you want to build it correctly
@tylerstansfield9569
8 жыл бұрын
will it be alright if there not torqued?
@Solitude313
8 жыл бұрын
You didnt torque them did you? Most likely not, but you could have some head gasket problems or seating problems, but like I said probably none for you to notice
@tylerstansfield9569
8 жыл бұрын
i haven't put it back together! do you know anywhere i can find the torque specs for it?
@Solitude313
8 жыл бұрын
I just have a book, maybe I can look up the specs, what all you need?
@teresacavo2151
6 жыл бұрын
The 27 mil nut
@Scott46Lee
6 жыл бұрын
I have a 1990 300 that's not getting compression at all, did a top end, new piston, new valves, and honed the cylinder and still no compression. Any ideas?
@Solitude313
6 жыл бұрын
Everything timed correctly on TDC?
@kaleosantos6313
4 жыл бұрын
U wanna sell it?
@Scott46Lee
4 жыл бұрын
Kaleo Santos my 300?
@kaleosantos6313
4 жыл бұрын
Yeah
@Scott46Lee
4 жыл бұрын
Kaleo Santos it’s long gone. Traded it for a 450 Foreman
@masonshelton6424
7 жыл бұрын
I changed my secondary clutches to the dirt racer clutches and now when i put it into gear it jumps hard as hell! How do i stop that from happening?
@NelsonCreekCustoms
6 жыл бұрын
Idle down, adjust clutch play, if that doesn't do it deal with it lol a lot of em do it especially the 350 ranchers, I wouldn't be all that concerned as long as it doesn't bang the tranny to hard
@Fl_bluecollar
6 жыл бұрын
How difficult is it to remove the engine from the bike? I’ve got a 2wd and need to do the top end on it.
@jasonmclaughlin243
6 жыл бұрын
Cory Mumm Im thirteen i took it out in an hour or less only with wenchs nd rachets
@masonmccraw3637
8 жыл бұрын
my clutch slips when I Get on it what do I gotta replace ??
@rcmen2637
6 жыл бұрын
Mason Mccraw the secondary clutch pack it's easy
@glen3993
6 жыл бұрын
before you take those 4 bolts out of that clutch will the inside move freely from the outside ? if it does then what
@Solitude313
6 жыл бұрын
It should not move, only the bearing
@glen3993
6 жыл бұрын
if i rotate the outer part of the clutch on the crankshaft the outer part of the rear clutch will spin but not the inside, does this mean my Disc are wore out?
@davidmcgray5924
8 жыл бұрын
When I put that plate with the springs on the secondary clutch how much do I compress the springs and the shifter bond do I put that on
@Solitude313
8 жыл бұрын
All the way down till the bolts are tight
@davidmcgray5924
8 жыл бұрын
And what about the kick start do you have to wind it up and how like can you just put it in there and turn it backwards
@Solitude313
8 жыл бұрын
+david mcgray I'm not by my set up but I believe you put the hook on the holder and turn it clockwise untill the lip catches
@teresacavo2151
6 жыл бұрын
How can I remove the reversed thred nut without an impact drill?
@Solitude313
6 жыл бұрын
Wedge something between the gears possibly.. Some use a Penny or a Screwdriver.
@teresacavo2151
6 жыл бұрын
I pulled the spark plug and used a boot lace and it worked. Thanks for the quick reply!
Пікірлер: 46