Damn bro. Good video. Can't believe all the hate you're getting for just showing how you do it. Big props by just using a freaking open end wrench to get that bearing in.
@troymckoy113
3 жыл бұрын
Thank you so much for saying that the race is leftover from the old bearing. I thought it was a separate part. Only you made that clear!
@TomAustin303
3 жыл бұрын
God bless you! That picture wire trick was EXACTLY what I needed! Neither of the two snap pliers I have were strong enough. I uses a vise-grip instead of a c-clamp. That you!
@user-ol3yd8mx3c
5 ай бұрын
Man! Very informative . Keeo making great videos. Will subscribed. 👍🏽. Thank you.
@theniceneighbor
2 ай бұрын
I bet if you check every dads toolbox mist of them have that same craftsman ratchet. Lol😂 i was given mine in high school and im in my 40s. Still works great.
@greenmagicman8114
5 жыл бұрын
The only power tools used were a $9.99 angle grinder and a friends Kobalt medium strength impact gun with air compressor and I only used that to remove the wheel spindle nut quicker. I suppose you could use a hacksaw and a very long cheater bar on the end of the 36mm socket.
@michaelpukmel4776
3 жыл бұрын
Thanks Green!!!!!
@staypositive4358
3 жыл бұрын
Wow! This is an excellent tutorial and answered all my questions. The only part I didn't like was the handing of the clip ring. You can get clip ring pliers for pretty cheap and not risk getting smacked in the wrong place by a flying ring. Great job overall!
@greenmagicman8114
3 жыл бұрын
True, fair enough. I just didn't have them on hand and my tool set is pretty broad and pretty complete, but don't have those. So was a little work around to complete the job. Putting a towel over it will easily catch a flying ring. Sort of it you like to put a towel over a bottle of champagne if one is the worrying type so to speak. But in this case it should be done, that ring could sail and injure someone.
@anthonykulas2624
3 жыл бұрын
That snap rings built different bro promise, broke two pairs of snap ring pliers doing mine, still got the other side to go
@kaospow
4 жыл бұрын
Nice vid. Only time I cringed was seeing you press that bearing in using the open end of that wrench . Great job though thanks for info doing this . Now I see what I'll be up against when I tackle this job myself.
@greenmagicman8114
4 жыл бұрын
Thank you!! It’s an interesting and satisfying job. Best of luck on yours.
@damojan
3 жыл бұрын
Yeah, are you aware that wrenches have box ends on them?
@Dhldakram5
6 ай бұрын
I just buy the whole knuckle loaded with the bearing and a lower ball joint, so much quicker, has a brand new backing plate, mine was rusted off
@pizzamon795
3 жыл бұрын
in hindsight you want to break a lot of those bolts and fasteners lose before you go take it all apart.
@syntaxerorr
Жыл бұрын
Great video. Thanks.
@dustyroads5811
3 жыл бұрын
Take the caliper and roter off first, its easier to loosen bolts , and less weight on the spindle, and brake line.
@huyquoctran2088
2 жыл бұрын
What brand wheel bearing did you use? I notice even the name brand ones nsk, skf and timken are all made in china now in 2022. They once were made in usa 😅
@greenmagicman8114
Жыл бұрын
Timken
@pizzamon795
3 жыл бұрын
I just unplug the cable for the ABS wheel sensor inside the engine bay. Mine are completely seized in there
@greenmagicman8114
3 жыл бұрын
So then the cable line fishes right out of the car body and follows the spindle / hub when you remove it all? Didn't know that could be done, that's handy. Thanks for the tip. Those ABS sensors always seem seized in there and too delicate to not break if your apply the force needed to remove them. Better off just leaving them jammed in the spindle unless you want to risk replacing the sensor as well.
@mr.nobody4900
3 жыл бұрын
So, 8 Gen Honda Accord front wheel bearing replacement on a Mazda Car?
@dakotamiller643
2 жыл бұрын
Just Mazda rims 😂
@bobbofly
4 жыл бұрын
Your center cap on that rim has a Mazda symbol...
@greenmagicman8114
4 жыл бұрын
Yes it does. Those rims are Infiniti G35 coupe 18” wheels. However I got the set used from a person who had them not very successfull mounted on a Mazda3 Speed turbo. He sold me the set. Inifinit wheels will bolt on to Hondas. The prior owner got Mazda emblem stickers and placed them on these infinti stock wheels. I have since removed those stickers. And the irony is I have Mazda rims with snow tires for winter.
@martinosvath5285
4 жыл бұрын
I love that you don’t mention what year Honda accord that we’re working on
@tonytellitright9713
3 жыл бұрын
He said 8th gene
@lonestar275
3 жыл бұрын
Thats because its not even an Accord. At 0:49 the caption said Infiniti
@staypositive4358
3 жыл бұрын
@@lonestar275 . He said in another comment he got the wheels elsewhere.
@ChunkyLover53atAOL-com
3 жыл бұрын
@@lonestar275That's because it's Infiniti wheels on an Accord...
@greenmagicman8114
3 жыл бұрын
Uh, well, the wheels are Infiniti G35 'track edition' wheels. They can fit on Hondas. I just pointed that out - because the center opening on the Infiniti wheel is too narrow to use for the trick of loosening the wheel spindle. I got the idea to use the Honda supplied spare tire for that step. That has the correct wider opening.
@bamram2673
5 күн бұрын
Just replace the whole knuckle and be done with it
@ethercreatures
3 жыл бұрын
I am wondering why you didn't use the impact drill on the handy work with the manual press? Seems like an idea to me although not a mechanic.
@Ihavetruth22
2 жыл бұрын
its about control.
@smallbeans101
3 жыл бұрын
Just spend the extra 20 bucks and get a pre pressed one
@Ihavetruth22
2 жыл бұрын
hub and bearing? don't you still need to press the hub onto the knuckle?
@huyquoctran2088
2 жыл бұрын
Front wheel bearing never comes with a pre pressed one ever! 🤦🏾🤦🏾🤦🏾
@datruth_706
Жыл бұрын
I get a humming noise like I'm inside a plane is that the wheel bearing? issue?
@greenmagicman8114
Жыл бұрын
Most likely yes. I described mine like a helicopter.
@davidarias7060
3 жыл бұрын
Why does it have mazda wheels
@pizzamon795
3 жыл бұрын
I have a ball joint removal tool that i use for the upper and lower ball joint and the outer tie rod end. It was $15 on Ebay
@greenmagicman8114
3 жыл бұрын
That's a handy tool to have. I 'loaned' that tool from Oreilly's at the same time I loaned the wheel bearing press kit. As long as you get them back you get your money back and it makes it a free loaner. Hoping to not have to do lots of suspension work in the future, but would be a worthy purchase.
@victorfoster7305
4 жыл бұрын
Neversieze everything !!!!!!
@staypositive4358
3 жыл бұрын
What?
@ChunkyLover53atAOL-com
3 жыл бұрын
@@staypositive4358 It's a great penetrating fluid. Spray, soak, and repeat.
@greenmagicman8114
3 жыл бұрын
Decent tip. I do use the Anti-Seize on some of my jobs (like oxygen sensor replacements and exhaust stuff).
@Ihavetruth22
2 жыл бұрын
@@staypositive4358 Anti seize copper
@jessez5536
4 жыл бұрын
I have a 2000 Honda accord that I'm about to do the front wheel bearing but when I got the new bearings they dont have a magnetic on either side but my car has the abs sensor so now I'm lost and dont know if I should I install them or what side should I put them in or would it matter?
@staypositive4358
3 жыл бұрын
I would have probably called the part maker and ask them why there is no magnet. Otherwise, how did it go?
@duanespeck2316
3 жыл бұрын
Wait, the bearings should have a magnet on them? I just got my bearings in the mail today and didn't notice any kind of magnet. What am i missing??
@greenmagicman8114
3 жыл бұрын
The bearings should have a slightly magnetic side to them. That's the tip that that is the correct side to face the ABS wheel sensor that you can see in the hub. It's very slight - a light weight paper clip barely is attracted to it and actually usually slips right off. Looking closely though, one side is a little more attracted to that paper clip and little more 'clingy'. That's my experience, and all 3 bearings I bought and installed are the Timken brand.
@user-ol3yd8mx3c
5 ай бұрын
Wtf you didn't finish it??
@profquad
3 жыл бұрын
Whose garage is it then?
@greenmagicman8114
Жыл бұрын
It ain’t mine. Was guest starring in it as its fully insulated.
@03vqdanny63
2 жыл бұрын
Where did you get the bearing tool
@greenmagicman8114
Жыл бұрын
Listed in video. Auto loaner tool.
@Ihavetruth22
2 жыл бұрын
Looks really difficult . Too easy to make a mistake and damage the bearing.
@mmorris1960
2 жыл бұрын
Y
@hidefinitionstoner9762
3 жыл бұрын
Title for Honda Accord but working on a Mazda wtf 🤦🏾♂️
@taramurray6994
3 жыл бұрын
OH? Oh it’s impossible to fit Mazda rims on a Honda. Or Infiniti. Just completely impossible. You guys are like detectives!
@hidefinitionstoner9762
3 жыл бұрын
@@taramurray6994 rite!!! Like whoever needs the help has the time to look up offfsets for wheels to see if Mazda wheels fit Honda or a Ferrari wheel will fit my Benz
@JoseMartinez-2018
7 ай бұрын
😂😂😂😂😂😂😂😂😂😂😂
@Ram14250
4 жыл бұрын
Turn down the music blasting in the background when you're making a video- PLEASE! So much noise. Hard to watch.
Пікірлер: 66