Thank you Tony for another excellent video. I have a CBF125 as my first bike and your videos have helped a great deal.
@anurag77719
8 жыл бұрын
lovely video. Waiting for you to service that centrifugal oil strainer as well.
@1bike2up
8 жыл бұрын
I opened it and it was OK, but I will video it next time 😉
@Panigale_nath
9 жыл бұрын
Another good video Tony, somebody who can actually show a proper job being done cheers 🍻
@1bike2up
9 жыл бұрын
thanks for that comment 😉 i do the vids hoping to help fellow bikers and to show its not that hard because i hate being ripped off, ie: garages!!
@geordieon2wheelscbr445
8 жыл бұрын
you left out the most important part showing the cleaning process! lol
@LUCASHEALEY
9 жыл бұрын
Thanks for the video, planning to do this soon. Can i just ask what did you clean the inside and strainer with ? Also what grease did you use ? Thanks
@night951521
8 жыл бұрын
If you still own that bike, could you please record a video about how to adjust the valve clearance. I would be very grateful ;)
@theturkeyshooter
3 жыл бұрын
The centrifugal oil cleaner is under the 3 screws on the crankshaft end, this also has a gasket and separates out a lot of aluminum dust you should check this next time
@1bike2up
3 жыл бұрын
I didn't get round to filming that bit !
@josselynrios1309
4 жыл бұрын
Amigo tengo una honda 125 honda cbf no me acuerdo cuanto discos lleva esa moto y cuantos dientes lleva el piñon d la.bomba d aceite
@rzrkilleriwishiwereahonda3625
7 жыл бұрын
you didn't take the circulation filter apart I'm sure that's filthy that's the thing with three Phillips head screws on it ribeye or clutches
@1bike2up
7 жыл бұрын
Topgunviking Hard To Kill its was and it was clean
@TroyaE117
8 жыл бұрын
And remember to use lint-free rags for cleaning or the strainer will clog up again, and very quickly.
@xd-ii6hn
5 жыл бұрын
i know this is a dumb question but what do you call the torque wrench adapter piece to unscrew the oil drain nut?
@scotth791
8 жыл бұрын
Hi their I've just cleaned out my oil strainer and I must of lost something inside cause I have no clutch but I see At 2:38 that theirs a little black circle thing on the casein and on mine I don't have that maybe that's why I don't have a clutch but I did have a clutch before I took the casein off so you couldn't tell me what that black thing is called or what so I can sort my ASAP please?
@driftr1dr719
9 жыл бұрын
Cheers for this guide Tony, I've literally gone at the casing with a rubber mallet and haven't been able to get the clutch gasket cover off at all - any ideas on how I could get it to loosen without cracking the case? Looks like it's jammed on.
@1bike2up
9 жыл бұрын
Drift R1DR it just needs tapped all the way around, be CAREFUL but you can go around to the other side and underneath you will see like a lip that you can tap, but be CAREFUL
@GeraltOfRivia99
5 жыл бұрын
does the oil in a dirtbike flow in from under the oil screen? or does it flow in from on top and go down?
@seeul8rwaynekerr
9 жыл бұрын
Do you happen to have the torque settings for those casing bolts please?
@1bike2up
9 жыл бұрын
stuckintraffic?getabike! I AM OLD SCHOOL!!! no torque settings for me!!
@akam2576
5 жыл бұрын
Nice
@s1914
8 жыл бұрын
Cracking vid. Doing mine tomorrow.
@1bike2up
8 жыл бұрын
😁
@richardwalker8398
3 жыл бұрын
Thank you for this video Tony. You make it look easy! :)
@davemorton9466
7 жыл бұрын
Thank you, much appreciated
@lul123
9 жыл бұрын
hi, so the first time you cleaned the oil strainer is at 30 000 km ? am i right? so after 30 000 km it's what it looks like if you never cleaned it?
@1bike2up
9 жыл бұрын
lul123 yes that is correct
@1bike2up
6 жыл бұрын
Yes, like in this video
@jhondiaz9514
8 жыл бұрын
la mano de obra para revisar porque está votando humo cuando está fria
@Hayley1993UK
9 жыл бұрын
ill be doing my cbf125 in a few days time :) thanks for the vid xx
@1bike2up
9 жыл бұрын
glad it helps ;)
@danieliacob3700
6 жыл бұрын
Many thanks for this brilliant video !!!
@compuzaire
8 жыл бұрын
muy buen video,, era lo que andaba buscando,, Gracias
@vibhorraj82q
6 жыл бұрын
Amazing video Tony I needed your suggestion on what should i do I have CBF 125 PGM-FI version . I recently serviced my bike from the service center Since then bike has generated a serious problem It stops after every 5-7 minutes When informed them about the problem they are charging me hefty money just to check so can you possible no what is the issue so that i can DIY.
@1bike2up
6 жыл бұрын
vibhor gupta sounds like fuel pump issue...
@vibhorraj82q
6 жыл бұрын
Tony Bigt thank you for the reply do you have any suggestions what exactly should I target in fuel pump or any video for reference
@1bike2up
6 жыл бұрын
vibhor gupta normally needs to be a new pump but i have seen them been taken apart although i would not reccomend it, is it "kanjarooing" "jumping" lack of fuel when engine is running. Could be a few things....
@vibhorraj82q
6 жыл бұрын
thanks Tony for your help I will get my fuel pump checked as soon as possible and update you I just hope it's not a ecu issue
@tbayley6
5 жыл бұрын
I've read that the strainer can get clogged like this as soon as 1000miles, so it looks like the casings are assembled a bit dirty. Also, there often seems to be a bit of that grey rubber/gasket material. 125ccbikeclub.awardspace.co.uk/oil.htm#Centrifugal-Oil-filter
@R.O.S.S.C.O
8 жыл бұрын
Fantastic video. I'm about to change out the oil in my 2003 Gilera Cougar 125. Is it work doing this and checking the oil strainer?
@1bike2up
8 жыл бұрын
does the gilera have an oil strainer?
@R.O.S.S.C.O
8 жыл бұрын
i haven't opened the casing yet but I am presuming so, as is it a unbranded honda engine.
@1bike2up
8 жыл бұрын
Humm
@R.O.S.S.C.O
8 жыл бұрын
I bought a gasket for the clutch over any way do I am going to give it a try and see what happens
@1bike2up
8 жыл бұрын
+R.O.S.S.C.O let me know how its looking
@compuzaire
9 жыл бұрын
buen video amigo!! gracias
@dailewis673
8 жыл бұрын
Outstanding vid. Thank you.
@1bike2up
8 жыл бұрын
glad it helps ;) that's why I do the videos:)
@forevercomputing
5 жыл бұрын
You're not supposed to re-use that type of gasket. Why copper grease on the bolts?
@1bike2up
5 жыл бұрын
Next time you come to remove it you will see why 😉
@forevercomputing
5 жыл бұрын
Why would a gasket require grease?
@1bike2up
5 жыл бұрын
@@forevercomputing I will give you a few more years then see if you get it !
@forevercomputing
5 жыл бұрын
@@1bike2up Unlikely, my CBF is due a rebuild since 2016. Been off the road since 2017...
@anthonyabela
9 жыл бұрын
I have been driving this model bike for the last one month and I really love my bike. Now I covered 1200 km. This week a problem is bothering me and i cannot manage to solve it and i think you could help. The handle at the right (gas handle) just at the end there is a screw which is getting loose with every few km. I tried to tighten it but after few km it will untighten again could you help me to solve this problem pls.
@1bike2up
9 жыл бұрын
anthony abela you would be best to take it out and have a look, they are in fact weights to help stop the vibration. you might have to get new ones or if not use some gasket sealant and screw it in.
@anthonyabela
9 жыл бұрын
Thanks for your help I managed to solve to problem. As you suggested i took out the screw out and checked what was happening i managed to put some thread lock which is not permanent and it seems that the problem is solved.
@1bike2up
9 жыл бұрын
anthony abela good to hear :)
@sujoydas5151
6 жыл бұрын
My 4years old honda cbf stunner overheate after running 4k.m. what is reason?
@1bike2up
6 жыл бұрын
SUJOY DAS have you checked the oil? What oil are you using? Air filter when did you replace?what is the ambience temperature there?
@ericdaudre4694
4 жыл бұрын
Thanks for this vidéo 👍, i'am french and i cherche this oil filter .
@babaig7984
6 жыл бұрын
Sir, i baught new honda unicorn 160, 1st august 2017, After changing my biker's engine oil, the engine caps were to stop, it took some sands and I stopped it without being clean, Is that a little sands of oil stenner filter? Or will my whole engine get worse? please answer me, i have no extra money for new one
@1bike2up
6 жыл бұрын
Sadhan Giri take apart and clean and flush (diesel would be the cheapest way to flush)
@babaig7984
6 жыл бұрын
i am dont know how to flush , service center not flushing my engine
@1bike2up
6 жыл бұрын
Open engine and wash (flush) with diesel
@babaig7984
6 жыл бұрын
any video reference please, open engine mean open cluch cover?
@babaig7984
6 жыл бұрын
engine oil stainer not filtered a bit of sands?
@mysurlytrucker7510
8 жыл бұрын
are you doing the centrifugal filter, is it difficult to do.
@1bike2up
8 жыл бұрын
I did not do it here as I had a look and was OK , but that video is on the cards
@1bike2up
8 жыл бұрын
not hard at all, 3 screws if I remember
@mysurlytrucker7510
8 жыл бұрын
thanks.
@1bike2up
8 жыл бұрын
😂
@jamesmilner265
6 жыл бұрын
What did you use to clean the inside and the screen? Thanks!
@forevercomputing
5 жыл бұрын
Brake cleaner is fine.
@prince-qo1oz
6 жыл бұрын
total km your bike
@jhondiaz9514
8 жыл бұрын
cuanto cuesta el cambio de cadenilla
@1bike2up
8 жыл бұрын
cambio de ?????
@fatjoe205
7 жыл бұрын
Never lubricate the gasket. Just clean and degrease both surfaces and put dry well.
@1bike2up
7 жыл бұрын
fatjoe205 have been lubing gaskets for over 30 years with no probelms, alias with it lubed i have been able to reuse sometimes...
@fatjoe205
7 жыл бұрын
You are doing bad, ask the mechanics.
@1bike2up
7 жыл бұрын
fatjoe205 lol
@fatjoe205
7 жыл бұрын
Do not laugh. My colleague works on the suzuki service and no mechanic lubricates such gaskets. It is against the "rules". Lubricate oil filter seals but not this gasket.
@1bike2up
7 жыл бұрын
Each to their own big lad.
@tbayley6
5 жыл бұрын
Does this also apply to the 2015 replacement, subtly renamed CB125F?
@1bike2up
5 жыл бұрын
I think it is exactly the same
@forevercomputing
5 жыл бұрын
@@1bike2up No, there are some changes, the power output is different, but getting to the strainer would be the same process.
@sunturoyroy2066
5 жыл бұрын
Nice video bro
@stephendixon3696
8 жыл бұрын
tony can you tell me how much oil to put in the engine please? around abouts
@1bike2up
8 жыл бұрын
1 Lt , but with full strip down 1.1lt
@stephendixon3696
8 жыл бұрын
+Tony Bigt thanks tony
@nagibnagz
6 жыл бұрын
after how many kilometers you changed it?
@1bike2up
6 жыл бұрын
nafiul nagib 32,000kms
@nagibnagz
6 жыл бұрын
thnk u..:)
@thuannho1992
5 жыл бұрын
its for honda cbf 125 2011 version? thank you
@forevercomputing
5 жыл бұрын
It's the same engine apart from the colour change right up to around 2015 when it changes to the CB125F, or CBF125R depending where you are in the world
@lukasl7421
7 жыл бұрын
Hey buddy, thanx for video! When can you recommend me clean oil strainer? After 30 000 km?
@lukasl7421
7 жыл бұрын
I have only 9000km in my CBF now
@1bike2up
7 жыл бұрын
Lukáš L or before!!!
@forevercomputing
5 жыл бұрын
@@lukasl7421 Officially to "check" every 7,500 miles, or 12,000km
@Sahilgautam491
5 жыл бұрын
Kick start install possible?
@forevercomputing
5 жыл бұрын
Check out parts for the CBF Stunner 125cc. You'd need to order some parts for the Indian version. Where this was made.
@DANMUFC
8 жыл бұрын
how many miles is it before the strainer needs cleaning on cbf 125?
@1bike2up
8 жыл бұрын
+Danny Muirhead i think they say 7500 miles but as you see i left mine well passed that but i do change my oil like clockwork!!
@DANMUFC
8 жыл бұрын
+Tony Bigt i change my oil every 1000 miles. i don't know why they didn't just put a disposable oil filter on this bike, it seems a lot having to replace gaskets just to clean the filter.
@1bike2up
8 жыл бұрын
Danny Muirhead as I did on the video I greased the gasket well so I HOPE I do not need to use another one but saying that I will have to get one just in case!
@DANMUFC
8 жыл бұрын
so you used the old gasket? you didnt replace it?
@1bike2up
8 жыл бұрын
+Danny Muirhead no, the one in the video is new. I greased it well up so maybe next time it will not break / stick and might be able to use again.
@gorylizor
7 жыл бұрын
Did you use the copper grease for the gasket? Or some other kind of grease?
@1bike2up
7 жыл бұрын
gorylizor just normal grease for the gasket (in the small empty water bottle at the start)
@gorylizor
7 жыл бұрын
Thank you!
@forevercomputing
5 жыл бұрын
You don't need grease for the gasket. The only time grease is used is to hold it in place. This is what the dowel pins do as well as ensuring the cover goes back in the correct alignment. Some surfaces are gasket maker only. This isn't one of them.
@fatjoe205
7 жыл бұрын
What torque did you use for the clutch cover bolts?
@1bike2up
7 жыл бұрын
fatjoe205 all by touch
@adriangavrila6241
4 жыл бұрын
Its aseme for honda cbf 2015 gasket ?
@1bike2up
4 жыл бұрын
?
@adriangavrila6241
4 жыл бұрын
@@1bike2up the gasket also fits the honda cbf 125 2015
@1bike2up
4 жыл бұрын
@@adriangavrila6241 yes
@xd-ii6hn
5 жыл бұрын
do you clean the filter every time you change the oil?
@1bike2up
5 жыл бұрын
No way !
@xd-ii6hn
5 жыл бұрын
@@1bike2up i also have a cbf which says to clean every 2.5k miles, how many miles until you clean it? Is it dirty every time you did so? Thank you so much for replying
@1bike2up
5 жыл бұрын
@@xd-ii6hn I would do it every 20,000kms, oil change every 2,000 or 2,500 kms but the strainer 20,000kms
@DANDIIDAY1111
9 жыл бұрын
good video
@1bike2up
9 жыл бұрын
THANK YOU
@ster4454
9 жыл бұрын
Changed oil cleaned strainer and clutch is slipping help
@1bike2up
9 жыл бұрын
Ste r be careful when you put the engine case side back on to get the clutch arm in the right place, check the clutch cable is not too tight as well, what oil you using not that it should make a difference straight away....
@ster4454
9 жыл бұрын
Tony Bigt I didn't put cable back proper on arm didn't click in proper sussed it after a good look cheers for advice mate
@ster4454
9 жыл бұрын
Hi Tony just wondering if u could help since I bought my cbf 125 when I slow down gentley then accelerate again I get a little thrust nothing major or the kangaroo hop just a bit annoying and affects smooth riding any tip if poss
@prince-qo1oz
6 жыл бұрын
oil drain interwal cbf 125
@forevercomputing
5 жыл бұрын
2,500 miles for the oil change
@1bike2up
8 жыл бұрын
what did you see at 2:38??
@scotth791
8 жыл бұрын
It's on the clutch arm have a close look , Honda tell me I have to take my bike their for them to have a look but haven't got any way of getting it their :/
@1bike2up
8 жыл бұрын
+Scott Hutchinson are you part of the Facebook group?? if so PM me and I will sort this out with you instead of on here.
@Zajc3wpl
7 жыл бұрын
get one for Christmas - you really need one: www.ebay.co.uk/itm/Grammar-Expletive-Mug-Novelty-Funny-Gift-Mug-/290972346136?_trksid=p2141725.m3641.l6368
@sohailmehmood9144
6 жыл бұрын
Thanks... before miss get home lol
@tombartram7384
9 ай бұрын
Ur taking off the whole clutch cover to reach the oil strainer because Honda were too stoopid/lazy fit specific little hatch like Suzuki did with their GNs. Omg how crap.
@1bike2up
9 ай бұрын
To be exspected on a cheap bike and only needs cleaned once in a blue moon
@davidbaptista5767
3 ай бұрын
Need someone silicone our just the gasket?
@1bike2up
3 ай бұрын
Just gasket was fine
@davidbaptista5767
3 ай бұрын
@@1bike2up thank you
@poulhansen2415
8 жыл бұрын
Sounded like hard work, with all that groaning.
@1bike2up
8 жыл бұрын
that is age my dear youtuber! it comes to the best of us...
@TroyaE117
8 жыл бұрын
You did not clean the centrifugal oil filter !!! Take the three starheads off and clean it out !!!
@1bike2up
8 жыл бұрын
I did have a look but it was fine
@forevercomputing
5 жыл бұрын
Star head? Torx bolts?
@1bike2up
8 жыл бұрын
oh I still own it
@kasuga9359
8 жыл бұрын
+Tony Bigt I just bought one last week :D 2400km 2010. The stainner looked very dirty on yours, you had never clean it before 30 000 km ?
@1bike2up
8 жыл бұрын
I know....I'm bad ! This is true I had never cleaned it until 30,000 kms but I changed the oil like clockwork but it just goes to show the the sh*T that is there even changing the oil like clockwork!!!!
@redrapaz5685
7 жыл бұрын
x
@dineshpramanik3128
7 жыл бұрын
do some exercise ok dear
@1bike2up
7 жыл бұрын
Dinesh Pramanik i lift a pint everyday
@barnbersonol
7 жыл бұрын
What a crap design. You need to take off the clutch cover to get at the oil strainer. It should have its own little hatch.
@1bike2up
7 жыл бұрын
barnbersonol what ?!?!?! and then make it easy to do?!?!?! and how would they charge a days labour at the garage then?????
@cristianosousa823
3 жыл бұрын
@@1bike2up XD
@MDisaster
7 жыл бұрын
Save yourselves the potential cancer and wear gloves when handling used engine oil, people.
@sylwiazacharko1222
7 жыл бұрын
What did u use to clean all inside? Great tutorial:)
Пікірлер: 173