I love the help this video gives. I apologize if i missed it but did you use a new gasket or reuse the old one? I thought you put it on without a gasket. Also the steel plates have a rough and a smooth surface, which way is supposed to be installed outwards toward the mechanic? Nicely documentet video for noobs like me
@MotorcycleRepair
Жыл бұрын
There is no gasket installation scene because the gasket is not a new one and the existing one is reused. The iron disc plate has no front and rear distinction. You can install it however you like.
@apg4gearhead
Жыл бұрын
@@MotorcycleRepair thanks how about when installing the last fiberplate? Does it have a specific orientation?
@MotorcycleRepair
Жыл бұрын
@@apg4gearhead "Last fiberplate?" What part is this talking about?
@apg4gearhead
Жыл бұрын
@@MotorcycleRepair sorry i meant friction plate. I saw another comment about how the last friction plate that gets installed needs to be oriented in a specific way but you guys didn't do that and i wondered why :)
@MotorcycleRepair
Жыл бұрын
@@apg4gearhead Yes... the mechanic in the video says that there is no problem even if it is installed like the video.
@aawre6301
Жыл бұрын
항상 잘보고 있습니다. 혹시 클러치 디스크 맨 마지막 한장은 잘못 꼽으신거 아닌가요...? 마지막장은 옆에 홈 파여있는곳에 넣는거 아닌가요..?
@MotorcycleRepair
Жыл бұрын
네...대부분 대림 오토바이들도 말씀하신대로 하는 것이 맞습니다. 하지만 저렇게 장착을 하여도 문제가 생기지는 않습니다.
@aawre6301
Жыл бұрын
@@MotorcycleRepair 네 감사합니다.
@이민용-d7q
Жыл бұрын
대림 배달오토바이 오일 넣은거 같은데 좋은가요?
@MotorcycleRepair
Жыл бұрын
네 대림 100% 오일 입니다. 좋습니다.
@raultudor2000
Жыл бұрын
Great video, bit you made a mistake when you mounted the new clutch plates. The last clutch plate you mount it wrong.
@MotorcycleRepair
Жыл бұрын
Ah... that's right. It was installed in a different way than before. It is purposely mounted differently to use the disk longer. 😄
@berndb.b4509
Жыл бұрын
So einfach geht das ?
@MotorcycleRepair
Жыл бұрын
Angenommen, Sie sind ein absoluter Anfänger, nachdem Sie dieses Video 2-3 Mal angesehen haben, Was ist, wenn Sie Werkzeuge für die Motorradwartung haben? Sie können diesen Kupplungswechsel auch durchführen. 😊😊😊(독일어) Assuming you are a complete beginner, after watching this video 2-3 times, What if you have tools for motorcycle maintenance? You can do this clutch replacement too.
@raultudor2000
Жыл бұрын
The last plate must not be aligned the same as the first four. There a special notch in the clutch basket for the 5th plate
@MotorcycleRepair
Жыл бұрын
thanks for the good point (What you said is correct.) I asked the service center mechanic... It is said that it was installed that way on purpose. They say that if you install it like that, you can use it for a long time.
@-I.S.T.P-
Жыл бұрын
드레인볼트 끼우는데 토크렌치가아닌 손토크ㄷㄷ 아무리 숙련자 라고 하지만 너무하시네 또 케이스까는데 고무망치가 아니라 쇠망치써도되나요? 125라고 너무 막하시는거같은데
@-I.S.T.P-
Жыл бұрын
+습식 다판인데 오일에 안적시고 바로꼽으시네 저배기니 막하시는거같은데 저방식그대로고배기 작업하면 바로 작살납니다 또한 토크렌치가 아닌 임팩으로 걍 조지시고 크랭크축 작살납니다 아무리 숙련자라고 하셔도.. 벼는 익을수록 고개를 숙인다고합니다 부디 규정 메뉴얼대로 해주세요 오도바이 망가져요
Пікірлер: 32