I can watch any of your video anytime any day, great job.
@hardlymovingpro
4 жыл бұрын
I appreciate that!
@cw5118
3 жыл бұрын
I didn’t have those Honda parts for the press so I used an old strut knuckle bolt and an old axle nut with the press and then a 30 mm socket with a mallet and VOILA! 😃
@hardlymovingpro
3 жыл бұрын
Good for you making your own make shift solution!
@jacobfarkas3916
Жыл бұрын
I used the greasable upgraded ball joint by mevotech on my Toyota Echo. I was really impressed with the quality. Nice video.
@hardlymovingpro
Жыл бұрын
Good for you!
@ElectricPulse100
3 жыл бұрын
Great video. Straight to the point and very informative.
@hardlymovingpro
3 жыл бұрын
Thanks.
@nitin7855
2 ай бұрын
Thank you so much
@hardlymovingpro
2 ай бұрын
You bet!
@leod3963
Жыл бұрын
Nice video so you really recommend these mevotech ball joints I need lower ball joints for my accord
@hardlymovingpro
Жыл бұрын
It's the next best alternative to a factory ball joint.
@Usmanthemecano
4 жыл бұрын
Beautiful
@hardlymovingpro
4 жыл бұрын
Thank you! Cheers!
@bwest-yq3uc
4 жыл бұрын
I am not familiar with that brand of ball joint...here in the lower 48... Educational video... for Honda owners.
@hardlymovingpro
4 жыл бұрын
Mevotech has been around for awhile as an aftermarket parts provider. I've found their quality control to be excellent, their parts always fit and they have a good tech support line.
@evanepp
4 жыл бұрын
Great job as always! Thank You!
@hardlymovingpro
4 жыл бұрын
Our pleasure!
@jacobfarkas3916
Жыл бұрын
I like your snap ring plyers. I'm lacking a good pair with tips.
@hardlymovingpro
Жыл бұрын
Plenty to chose from on Ebay or Amazon.
@dannynica7480
3 жыл бұрын
hello, nice video, but i have a question, the grease fittin you just use it to add grease and then took it off, So what about if you need to add grease in the future??? you are disassembly everything or you are using a needle injection to add more grease??
@hardlymovingpro
3 жыл бұрын
Good question. There's not enough room to have a permanent grease fitting on the ball joint. The fitting would rub against the bearing cup of the cv axle. If you want to re-grease, you'd have to remove the cv axle from the hub, screw in the fitting and then re-grease.
@simonrummel2019
10 ай бұрын
Impact driver should not be used on a ball joint press it will destroy the threaded portion of the press. Yes I know everybody does it, that don't make it correct.
@hardlymovingpro
10 ай бұрын
Thanks for sharing! You're right for the inexperienced techs. The threads could strip if over torqued.
@jimmysmith3255
Ай бұрын
Maybe don't buy such a cheap press
@kevinmahon9921
3 жыл бұрын
Do you think a pickle fork and hammer would work to get the ball joints out if I don't have that socket adapter kit you are using?
@hardlymovingpro
3 жыл бұрын
Only for separating the ball joint from the lower control arm.
@WizzRacing
3 жыл бұрын
If you don't have an Impact driver.. You can use a lead anchor setting tool for 3/8" drop in anchors....Just whack the head of the bolt with it...It will jar the bolt loose..
@mauriciochacon2418
Жыл бұрын
Perfect
@hardlymovingpro
Жыл бұрын
Thanks!
@bwest-yq3uc
4 жыл бұрын
What were the symptoms? Enjoyed the video. What tools or brand of tools, depending upon the tool - you rather use?
@hardlymovingpro
4 жыл бұрын
Thanks for your comments! Thunking noise when the wheels are at full deflection and going up a driveway or over bumps. The upward motion of the wheel combined with turning pulls the ball of the ball joint out of the ball joint socket. As the wear gets progressively worse, the front wheels will wonder and a wheel alignment job will not correct it. I'll be listing the tools and parts used this evening in the text description area of this video.
@jdmmodding9199
3 жыл бұрын
Where I buy that installation adapter to install the new ball joint ?
@hardlymovingpro
3 жыл бұрын
Link to the adapters provided in the text description of the video.
@dannysautorepair
4 жыл бұрын
Great video thank you
@hardlymovingpro
4 жыл бұрын
Glad you enjoyed it
@FACAVCMESMODIY
2 жыл бұрын
Muito bom vídeo, assistindo aqui do Brasil, também tenho um Honda Civic e posto vídeos dele, já me isncrevi no canal para aprender mais com Você... Aqui não temos essa ferramenta que usou para soltar a esfera, será que tem algum site que venda e envie para o Brasil...???
@hardlymovingpro
2 жыл бұрын
¿Se pueden pedir piezas de Amazon? He enumerado las herramientas que utilicé en la descripción de este video.
@Longtrailside
4 жыл бұрын
Well done!
@hardlymovingpro
4 жыл бұрын
Thanks!
@danielochoa831
3 жыл бұрын
nice work..
@hardlymovingpro
3 жыл бұрын
Thanks for the visit!
@jaymez858
7 ай бұрын
Thanks for sharing. Do you have to torque the castle nut while under load?
@hardlymovingpro
7 ай бұрын
Can torque with or without load.
@andrewm.4168
6 ай бұрын
There is no reason to take the rotor off the knuckle. Leave it attached. You can remove the axle nut with the rotor attached. You do need to remove the caliper though.
@hardlymovingpro
6 ай бұрын
Would be somewhat cumbersome pressing out the old ball joint with the knuckle attached rotor held on with only one screw.
@intelectualsanchez5519
4 жыл бұрын
Movotec are good parts
@hardlymovingpro
4 жыл бұрын
Yes they are.
@Lalambz
Жыл бұрын
do you need to do this if you’re replacing the whole control arm?
@hardlymovingpro
Жыл бұрын
Usually want to replace the ball joint with a new control arm.
@jeffreybass5479
3 жыл бұрын
Didn't see anything about removing the tie rod end. Isn't that also connected to the knuckle?
@hardlymovingpro
3 жыл бұрын
Nope. Tie rod is connected to the suspension strut
@doctor_arz
3 жыл бұрын
Do you need to do an alignment aftet this job or not necessarily? I just changed my tie rod ends, tje strut mounts and the wishbone bearings, i have a little knock when starting off while also stearing and i just did an alignment. The Ball joints would be the next job to do
@hardlymovingpro
3 жыл бұрын
Absolutely! Do the alignment AFTER you do the ball joints. You can also get life time alignment agreements with some shops like Firestone so you can bring your car back as often as you want.
@Brettisgg
4 жыл бұрын
what is your preference regarding sealed vs grease-able ball joints? I've always used the oem toyota that are sealed personally and they seem to last.
@hardlymovingpro
4 жыл бұрын
My preference is grease-able everything. There are parts manufacturers that exceed oem standards. Mevotech's is one of them with their TTX ball joint series. I'll show you in a future video installing one on a Toyota.
@triggersafe1
2 жыл бұрын
Mevotech...Do they last?OEM lasted about 120K miles.
@hardlymovingpro
2 жыл бұрын
One of the better aftermarket IMHO. The factory ball joints are weak.
@PlanetMalcolmX
5 ай бұрын
🥇
@hardlymovingpro
5 ай бұрын
👍
@danielguzman8346
2 жыл бұрын
The green rubber thing around the ball joint wont get damaged?
@hardlymovingpro
2 жыл бұрын
Nope. That's the dust boot.
@capricornio9343
3 жыл бұрын
How you know,when you need to replace ball joints,what’s the problem you advise they’re broken? Thank you in advance
@hardlymovingpro
3 жыл бұрын
Visual inspection for split boots and/or ball-in-socket free play test with a pry bar
@capricornio9343
3 жыл бұрын
@@hardlymovingpro thanks for your help 👍🏼
@hardlymovingpro
3 жыл бұрын
You bet!
@mr.sierra4409
7 ай бұрын
What happens if I don't change?
@hardlymovingpro
7 ай бұрын
Could eventually break and the wheel will collapse inward.
@Adi_Russo
8 ай бұрын
OEM Code for ball joint?
@hardlymovingpro
8 ай бұрын
Don't have it.
@agustinherrera5600
2 жыл бұрын
Did the ball joint come with the plug or where did you get it ? I had an issue finding some plugs for a 04 honda accord it was the same process but mine didnt come with a plug
@hardlymovingpro
2 жыл бұрын
Are you referring to the grease fitting plug? If so, the replacement joint came with L shaped grease fitting adapter (to pump in grease after installation and to be later removed) and a green rubber press in plug (to replace the grease fitting adapter).
@agustinherrera5600
2 жыл бұрын
@@hardlymovingpro the green plug you used to to plug the hole since there was no room to leave the grease fitting installed . Mine came with the grease fitting but there was no clearance for it on the car so i needed a plug for the hole and I couldn’t find one
@hardlymovingpro
2 жыл бұрын
The green plug is the plug. If you're not happy with it, call Mevotech to get a screw type metal plug.
@agustinherrera5600
2 жыл бұрын
@@hardlymovingpro this is not the same part that i have . I was just wondering if the plug came with it . I clicked the link you had and in the pictures it looks like its a dust cap for the grease fitting
@daynnic
4 жыл бұрын
What is the tool called that you used to take off the rotor?
@hardlymovingpro
4 жыл бұрын
It's a mechanical impact driver. A link to the tool is in the text description of this video.
@abdalqadr1
3 жыл бұрын
Greetings for you from Iraq
@kevovq3727
Жыл бұрын
Can this fit 05 rsx Acura ?
@hardlymovingpro
Жыл бұрын
The suspension design is the same but the part is different.
@kingkon164
Жыл бұрын
Nice video but I would have left the whole assembly on the car.
@hardlymovingpro
Жыл бұрын
Thanks! Would be difficult keeping the assembly on the car doing the ball joint.
@luisamoa2500
4 жыл бұрын
Sealed. No one ever remembers to grease those zerk fittings.
@hardlymovingpro
4 жыл бұрын
I know but the ball joint does come pre-greased. I'm just adding a little more.
@tonycotta6602
3 жыл бұрын
Ijust knock them out with a hammer then just use the tool to install
@hardlymovingpro
3 жыл бұрын
Whatever works for you.
@darknight508
3 жыл бұрын
Tools tools tools...!
@hardlymovingpro
3 жыл бұрын
Tools make the job easier and less time consuming.
@101vids2
2 жыл бұрын
Mevotech is utter trash. I've had 2 of the premium ones so far and they barely lasted a year each in my civic before they were loose. Very dangerous.
@hardlymovingpro
2 жыл бұрын
Thanks for sharing your experience with Mevotech ball joints. Haven't had the same problem you had. Their supreme grade comes with a lifetime warranty and suggest you call their tech support department to see what they can do for you.
Пікірлер: 90