as someone who just replaced all of these belts i love you
@glennruaza5810
2 жыл бұрын
I was having a hard freaking time installing the AC Compressor belt this afternoon and was all bit a failure! Thank you so much for this tutorial!
@FOCOTB72
3 жыл бұрын
Remember not to over tighten the bolts on the pulleys, the mechanic did that to our ac compressor pulley and it snapped off, now creating a nightmare extraction job from the side of the engine that couldn't be tighter to try and access. If you're missing your ac compressor pulley, before you go get anything, get a flex mirror and a good light and try to see if you can see into the bolt hole for the broken off bolt inside. Save you a bunch of tear down in the process.
@vintagedudestuff
3 жыл бұрын
I had to replace my belts today. Your post was very helpful.
@ThadFMH2Y
3 жыл бұрын
Thank you for posting this video. 6 hours later and they are all changed.
@cquinn185
4 жыл бұрын
Thank you so much. I just finished changing all three belts and putting everything back together. This video was really great and now my daughter’s car is not squealing anymore. Great video brother.
@YourCarGuyDR
4 жыл бұрын
C Quinn thank you for the feedback.
@3agl3H3art
2 жыл бұрын
I wanted to say thanks alot... Just did my Belt on my 2000 crv manual and Damn must i say i messed up and didn't release the engine mount on the left side. So the leeway for the lower engine torque mount went a 1/2 " so there was no play but i made due and got them on there... Thanks once again...
@jacklloyd1980
3 жыл бұрын
Thank you so much! Used this video as a guide to tension a loose alternator belt and my car is running so quiet now!
@jonnel2000
Жыл бұрын
i found it hard to tension my loose alternator belt... any specific thing you did for it to get the required tension?
@ImperialLightandMagic
2 жыл бұрын
I've just managed to replace all 3 belts with the help of this video. Thanks so much, you saved me an awful lot of time and messing around.
@starlenenava6660
2 жыл бұрын
Thank you for doing this video on the correct order! I initially followed another video that really screwed me up. Then I came across yours and all is well!
@eliasshadow5643
5 жыл бұрын
Who ever has this problem! Go ahead and do it this is a great video explains it well.
@bryantspeedcustoms9795
3 жыл бұрын
Awesome Video You Did A Great Job - But Pro Tip If You Take The Wheel Off And Put The Driver Side Lower Control Arm On A Jack-Stand You Can Then Lower The Motor Even More And Get The AC Tensioner With A Socket And A Ratchet And Can See Better Which Makes It All Easier 🔧
@R3DF0XTR0N1C
4 жыл бұрын
thanks fixed my 2001 slowly! with this video fortunately. appreciate it
@YourCarGuyDR
4 жыл бұрын
Adam Neville yep it’s not a quick job.
@R3DF0XTR0N1C
4 жыл бұрын
@@YourCarGuyDR especially since my engine mount was even more SHOT lol
@JoshLee3001
3 жыл бұрын
Successfully did my a/c and power steering belt thanks to you. Thank you you teacher
@kirohesler4632
Жыл бұрын
Gunna do this myself now thanks, all the mechanics quoted this work as 1000-1400$ and that's beyond rediculous.
@bushmaster2936
Жыл бұрын
Other than the audio, the video was pretty good and informative. Thank you.
@JJ_Geek
5 жыл бұрын
Good job would have loved to see a before and after
@lgero
5 жыл бұрын
very informative step by step, i had to change the belts while doing my ac compressor and condensor
@YourCarGuyDR
5 жыл бұрын
lgero I am glad it was helpful.
@yestoprint2932
6 жыл бұрын
Thanks good job, good teach, is a lot of work but is a challenge do it myself...thanks again
@xesxblackarrow7912
Жыл бұрын
Thank you for saving me time
@mattsowders7032
5 жыл бұрын
Thank you! I'm doing mine right now. And this helps so much man.
@YourCarGuyDR
5 жыл бұрын
Matt Sowders glad to hear it is helpful.
@cooljoe494
5 жыл бұрын
Just used this vid to change mine. No more squealing belts at 7AM. Huge pain to remove that AC pivot bolt. Recommend a short socket and a long breaker bar. Anyways thanks a ton
@demetricktipler4251
3 жыл бұрын
Right 😭
@tekamartinez5493
5 жыл бұрын
One of the best step by step videos I have seen really good and well explain 👍🏻
@YourCarGuyDR
5 жыл бұрын
Teka Martinez thank you.
@muyoyuclive5838
Ай бұрын
Great stuff.Thanks so much
@alexbieber684
Жыл бұрын
Thanks for the video! It made my life alot easier. If you dont have a impact drill grab yourself a breaker bar :)
@Carlosguerrero-yv9im
4 жыл бұрын
Very detail I appreciate it alot
@Caladan1616
3 жыл бұрын
Thanks for the help!
@AguilaJR
3 жыл бұрын
Thank you. Very helpful
@Airmanmx1
4 жыл бұрын
Nice video. Sure helping me.
@beargang8853
2 жыл бұрын
great video thank you
@CarlosPerez-up3xg
3 жыл бұрын
Thank you for this video
@dougsmart3678
Жыл бұрын
Very helpful video this is such a bad design it shouldn't be this hard to change belts just put tensioner pulleys on them and call it a day what Honda was thinking I have no clue
@theman5625
9 ай бұрын
Are u able to change the power steering belt without unscrewing the motor mount? Would I just be harder to put the belt on
@jakem183
4 ай бұрын
Great video!
@charlieward7606
6 жыл бұрын
great guide, seems straight forward enough except motor mount, got to change one of these tomorrow so atleast i know whats up before hand
@YourCarGuyDR
6 жыл бұрын
Charlie Ward good luck with it. This is one of the more difficult vehicles to change belts on.
@charlieward7606
6 жыл бұрын
im a apprentice mechanic had lots of annoying modern cars in, this should be fairly easy for me i think, only part that looks annoying is taking of the engine mount but even that is not hard, i regularly change gearboxes on campervans and those are a real pain sometimes, had one took me near an hour and a few bloody knuckles just to get the engine mount out. thanks for the answer and video :)
@YourCarGuyDR
6 жыл бұрын
Charlie Ward your welcome. Keep doing great work.
@ikarus_Fix_It
3 жыл бұрын
That's a good video, James. Scene transitions could use a little work, but very helpful with the car repair
@heryperez7379
6 жыл бұрын
Awesome video great help!
@YourCarGuyDR
6 жыл бұрын
Hery Perez thank you for the feedback.
@mei-niparnes3952
Жыл бұрын
Do you mind listing the belt specs for all three of them so I know I buy the right ones?
@hermijacobs6467
3 жыл бұрын
Hi can you please tell me the sizes of the alternator and steering pump belts?
@cresha270
4 жыл бұрын
Thanks for the video. Followed this for a 97 with a missing ac belt but am getting some squealing when the ac is turned on and sometimes when turning. So they are too loose?
@YourCarGuyDR
4 жыл бұрын
cresha270 if the belts are new then yes they likely need to be tightened a little bit.
@TheoBones-qb1jz
9 күн бұрын
Quite helpful.
@lgero
5 жыл бұрын
great video
@YourCarGuyDR
5 жыл бұрын
lgero thank you
@geiovanyayala1388
Жыл бұрын
Is it the same instructions for a -97-98 crv?
@ps7381
4 жыл бұрын
This is a really good video. Thanks for posting it. I have a 2000 CRV. Before seeing your video, I started to replace all the belts, got Pwr Strng belt off, loosened AC belt and then discovered the wretched motor mount. I don't have a floor jack or jack stands "yet", so I did an about-face and reinstalled the belts. My question is, what size floor jack (tons) should I use to support engine and where did you place the jack when jacking up the engine? Did you use any additional jack stands in other spots to support the vehicle while doing this? Any advice appreciated.
@YourCarGuyDR
4 жыл бұрын
P S the two most important things are to be safe and not damage anything. When I lift or support the engine I use a block of wood on my jack or jack stand between the engine and the oil pan. This will spread out the load and keep from breaking the oil pan. Just make sure not to lift to the point that you are lifting the vehicle. If you have the tire off I use a jack stand on the frame or k-member that supports the engine.
@jonnel2000
Жыл бұрын
when i replaced the alternator belt, it felt loose... is there a certain way to tighten the alternator belt? its the 4pk0820 belt... i guess (?)... btw, thanks for this very informative video!
@seanross1589
6 жыл бұрын
Thanks for the video. It is very easy to follow! How do you determine how tight to make the belts? In the service manual it gives all these forces the belt used flex and using a special tool to measure that, but all the videos I see just shows them putting them back together by eye. Is the super exact tension really that important?
@YourCarGuyDR
6 жыл бұрын
Sean Ross the exact tension isn’t a huge issue. If you make it too tight as in no deflection in the belt it can put more strain on the bearings of the various pulleys. If they are not tight enough you get squealing and premature belt wear. My rule of thumb is to get them tight but make sure I can get about 1/2-1” of deflection in the longest run.
@seanross1589
6 жыл бұрын
Perfect. Thanks so much for the quick reply!
@MrShakamuni01
5 жыл бұрын
@@YourCarGuyDR 1/2 inch to one inch with how much pressure on the belts? Or pushing pretty firmly and the only give will be at most one inch. I believe my mechanic tighten belts too tight after doing the timing belt. I fired him because of other issues with the car but I have to solve his bad job. it never seems worth to pay others to do things :-( on your car because so often I am fixing the side effects of their bad jobs.
@YourCarGuyDR
5 жыл бұрын
Alexis Tudor yes the 1/2inch to 1 inch rule is a pretty standard one. The deflection should be checked on the section that has the greatest distance between pulleys. Remember that belts that only have short runs definitely need to be on the low side of deflection.
@dianaphillips7927
6 жыл бұрын
I love the fenagling bar. Lol
@YourCarGuyDR
6 жыл бұрын
Diana Phillips my favorite tool.
@amerik556
Жыл бұрын
That is one lucky kid
@freedomofmotion
5 жыл бұрын
If you remove AC belt will everything else work okay? Think AC pump is dead horrible squeaking when ac is on.
@YourCarGuyDR
5 жыл бұрын
Freedom Of Motion you can remove just the a/c belt and everything else will be fine.
@skyscraper37
5 жыл бұрын
Great video...although my alternator was seized in place...got bolt on top loose and but on bottom off...sob wouldn’t budge...I’ll worry about it when the alt dies or the belt breaks
@YourCarGuyDR
5 жыл бұрын
Joel 1 they can be a pain when they are seized in place.
@skyscraper37
5 жыл бұрын
Your Car Guy DR yea I gave up for now...I’ll worry about it when the belt breaks or the alt takes a crap...21 year in the Cleveland area will do that...it’s the original too
@YourCarGuyDR
5 жыл бұрын
Joel 1 those Honda’s are hard to kill.
@emilybadri3169
5 жыл бұрын
I can't get the lower motor mount off due to a very tight, rounded bolt. Will loosing the buts on thr lower motor mount be sufficient?
@YourCarGuyDR
5 жыл бұрын
Emily Higgins you should be able to take the bolts out of the mount and get the belt out and back in.
@TheDerrty111
5 жыл бұрын
Its metrics 14mm but since you round out the bolts go buy a bolt extractor from lowes
@dale89811
4 жыл бұрын
This video has helped alot so far however I just can not get thr ac tensioner screw rod lose I'm using a socket on the end but it dont seem to be moving. I'm scared I'm going to shear it.
@YourCarGuyDR
4 жыл бұрын
Rule the roost make sure you loosen the pulley first.
@dale89811
4 жыл бұрын
@@YourCarGuyDR I had done,I managed it in the end with spray grease and by making more room,I removed the headlight to give better positioning. This video helps alot thank you.
@edwardpeter2652
2 жыл бұрын
13:05 for this bolt best position to operate is in front from the bottom.
@lagubrother1835
2 жыл бұрын
What are the belt sizes????????
@srworld3257
2 жыл бұрын
Why did you replaced all the belt did it sounds like the vehicle started to not want to accelerate right ?
@YourCarGuyDR
2 жыл бұрын
If I was going to do the job I went ahead and replaced all at the same time. The only difference was that with the new belts there was no squeal.
@luismanuelveradiaz9822
Жыл бұрын
Which of the three is the hydraulic steering belt?
@YourCarGuyDR
Жыл бұрын
It is the first belt in the video.
@luismanuelveradiaz9822
Жыл бұрын
but what is the number of the band of the hydraulic guide?
@luismanuelveradiaz9822
Жыл бұрын
Pliss?
@TurboRetard
3 жыл бұрын
How tight should the belt be on the alternator?
@baylordelrosario1465
7 ай бұрын
For the alternator I used a long extension wrench which worked best. For the AC I simply used the adjuster, then tightened the nut on it. For the power steering belt I pulled up physically with one hand (holding the power steering pump), then tightened essentially by hand. All 3 belts seem tight, but not crazy tight. Worked liked a charm.
@s.o.l8886
3 жыл бұрын
Can you remove the altenator belt without removing the other two belts?
@YourCarGuyDR
3 жыл бұрын
Steven O'neal you could cut it off but you would not be able to get the new belt on without removing the others.
@MrShakamuni01
5 жыл бұрын
If I am just to adjust the belt on the alternator which a lame mechanic tightened too much, do you feel I can access those belts without dropping the engine?
@YourCarGuyDR
5 жыл бұрын
Alexis Tudor yes everything can be accessed for adjustments without dropping anything.
@MrShakamuni01
5 жыл бұрын
@@YourCarGuyDR Thanks for the response. THings got a bit more complicated, My useless mechanic rounded off the bolt to the power steering mount so I cant get that out of the way. You think I can access the mounting bolt from the A/C from the bottom. I guess the only way to get the mounting bolt on the power steering is to grind it off and then take the pump off and then back the bolt out unless you know of a better way. Getting help in TN short of useless is challenging unless you want to pay a dealer a hundred dollars for each turn of a bolt :-(..
@YourCarGuyDR
5 жыл бұрын
Alexis Tudor there are tools for removing rounded bolts but there are times when the only remedy is to grind it off.
@TheDerrty111
5 жыл бұрын
@@MrShakamuni01 go to lowes they have a bolts extractor its call Irwin's bolt extractor google it so you know what it is. Trust me it works!
@MrShakamuni01
5 жыл бұрын
@@TheDerrty111 Thanks Derrty. I got lucky with my gator grip by grind the edges of the bolt back that were rounded and sticking the gator grip on. I will check out the Irwin's though because there is plenty of shitty mechanics rounding bolt.
@802Garage
6 жыл бұрын
Wow this makes me love working on a Subaru even more.
@keenanwalker1313
5 жыл бұрын
lol subarus are no easier to work on than hondas in fact this might be the one example of something thats harder to do than subarus around the same year js
@calebs4899
3 жыл бұрын
My top alternator bolt was on so tight that it rounded out. I’m screwed. Any ideas??
@YourCarGuyDR
3 жыл бұрын
There are some sockets that can sometimes take off a rounded bolt. Otherwise you can cut the head off or the bolt or remove the whole bracket.
@micahlarge7370
2 жыл бұрын
My AC belt broke is it OK to drive without the AC belt?Seems to run better
@YourCarGuyDR
2 жыл бұрын
Yes you can run without the ax belt.
@micahlarge7370
2 жыл бұрын
Thank you sir 🙏
@calebhiggins9681
3 жыл бұрын
I couldn't see the part number for that last belt, would anyone happen to know what all three belts are called so I could look them up?
@YourCarGuyDR
3 жыл бұрын
Caleb Higgins alternator belt, power steering belt and a/c belt.
@TaxedtoXXX
5 жыл бұрын
THANKS, im guessing a 1998 CRV is about the same. and i know i dont have all the tools.
@Christian-og2qh
5 жыл бұрын
Just worked on my 98 crv and its the same pretty much. A rachet with a 12 and 14 mm socket is all you need really
@cquinn185
4 жыл бұрын
I just changed all three belts on my 97 CRV, it is the same.
@ainoskribi3642
3 жыл бұрын
Please bro give me the references of the ac compressor belt
@artisticdrywall7368
4 жыл бұрын
Where do you place the jack at .. ?
@YourCarGuyDR
4 жыл бұрын
Artistic Drywall you can use the factory jack point just under the front of the drivers door or use the subframe.
@artisticdrywall7368
4 жыл бұрын
I know but I'm talking about the when supporting the engine. Plus where is the correct jack point in order to place my front jack stand in.
@YourCarGuyDR
4 жыл бұрын
Artistic Drywall when supporting the engine you can go under the oil pan but use a board between the jack and the engine the to spread the load. The front or rear of the engine subframe works for a point to put the jack stand.
@fonzerelle1
6 жыл бұрын
What a pain in the ass to replace a/c belt...have to remove a motor mount...a tire...power steering pump...holy small hands batman
@charlieward7606
6 жыл бұрын
lol i have to do this tommorow and thought the opposite, easy other than the motor mount, should try most modern cars they are heinous, most of what i get at work is modern french cars and stuff and they are god awful
@missouristate899
5 жыл бұрын
I never remove the motor mount when i did my belts.
@garrettbeck434
5 жыл бұрын
@@charlieward7606 Honestly modern cars have a single serpentine belt to change now and they're pretty easy especially since they mostly have auto-tensioners. The Crv also has the worst cabin filter design I have seen and I was a bmw mechanic.
@MrShakamuni01
5 жыл бұрын
@@garrettbeck434 but those auto tensioners go out every two years.
@garrettbeck434
5 жыл бұрын
@@MrShakamuni01 I mean that's simply just not true...
@charliegoodman8626
2 жыл бұрын
I did it and DID NOT Take off the Motor Mount!!
@hanslund308
3 жыл бұрын
Holy shait that was plenty of work just for the belts
@YourCarGuyDR
3 жыл бұрын
Yes it is.
@dusteyrose5883
2 жыл бұрын
You forgot to tighten both bolts on the a/c idler pulley/tensioner
@abednicoramotshwarapula7138
4 жыл бұрын
i the honda crv front engine mounting 1996 the same as the 2000 crv
@YourCarGuyDR
4 жыл бұрын
Abednico Ramotshwarapula yes it should be.
@jbentley-xt8oi
5 жыл бұрын
This is nearly the same way Honda Civics are done...😊
@YourCarGuyDR
5 жыл бұрын
jbentley8383 you are correct. The original CRV was based on a Civic chassis.
@alexlevingston
Жыл бұрын
Ok, so I changed the A/C belt and it still squeals. I think I will have to change the Idler pulley.
@YourCarGuyDR
Жыл бұрын
It is very likely that your idler could be bad. You can also make sure that your a/c compressor turns smoothly by hand when you have the belt off.
@Yes-hf6cw
2 жыл бұрын
That's a lot of work for just replacing belts. Why did they make it so complicated? So many repairs in this car is hard to do, even changing the oil can be hard with short oil filter.
@hunterjohnson1853
3 жыл бұрын
Everything is perfect but I can not get the engine mount bolts loose to save my life😂 tried a breaker bar and everything
@artgonzalez8625
3 жыл бұрын
I didn't need to because the belts passed without needing to take them off
@hunterjohnson1853
3 жыл бұрын
@@artgonzalez8625 mine car is the 1st gen like in the video and I won’t be able to take a belt off and on unless the engine mount is lowered
@ainoskribi3642
3 жыл бұрын
I mean the size
@georgewade4635
4 жыл бұрын
Mostly just poor camera angles and muffled mic sounds. Good words though.
@YourCarGuyDR
4 жыл бұрын
George Wade I will accept both the criticism and the complement. This was one of my first videos and due to the limited space very difficult to shoot. Still working on producing better videos but hopefully this is still helpful. Thank you for the feedback.
@georgewade4635
4 жыл бұрын
@@YourCarGuyDR Well damn man I really appreciate that you read this. I was being harsh but I'm glad you care enough to appreciate the feedback and try to improve. That's badass.
@YourCarGuyDR
4 жыл бұрын
George Wade I truly do appreciate it. I actually was on the fence over even publishing this video because I was so unhappy with the camera work.
@walterparada1530
4 жыл бұрын
I cannot for the life of me move the power steering pump out of the way
@YourCarGuyDR
4 жыл бұрын
Sometimes they can be very difficult to move. Make sure all the bolts are loose and use a pry bar. Be gentle so as not to break anything.
@MrStickynicky
6 жыл бұрын
I'm sure people really appreciate you making the video , i'm not being sarcastic. But what was the point of just loosening the power steering pump if you were going to take it out anyway, you could've just taken it out in the first place. Also you need a new camera man
@YourCarGuyDR
6 жыл бұрын
nicky I removed it in order to get a better view for the video. The job can be done with it in place.
Пікірлер: 145