Hello , i want to buy a 1998 trx 450es ,but the seller suspect a broken output shaft in two because he says the rear wheels are not turning , is it a big job to replace the output shaft and does it come out by the clutches side or the stator side?
@bubbachambers7976
3 жыл бұрын
I REALLY NEED YOUR HELP , I need a video on how to change a timming chain tensioner, please do a video on that .
@markfreeman408
5 жыл бұрын
Cool!
@bobzak9508
3 жыл бұрын
my 98 450 Foreman ran great and then I put Premium gas in and ran it for about an hour and started hearing a tinging like sound under pressure and then parked it, now it wont start, it turns over, just doesn't fire. any suggestions? Anyone???
@galliogarcia
3 жыл бұрын
Thanks for the video! Do I need to remove the engine to do this rebuild? Also do i need to remover the rear plastics to remove the exhaust from the top end?
@gregwright6565
4 жыл бұрын
Kind of a slightly off topic question, but it looks like you might know. I have a 2015 Honda Foreman and I'm thinking of getting a oil extraction pump to pull oil through the fill hole. Will the tube get to the lowest part of the case easily from the fill hole to get most of the oil out? I'm afraid I'll booger up my drain threads so I'd like to leave the drain plug alone.
@gregwright6565
4 жыл бұрын
@@MidNebraskaMotorsports thanks. I pulled the plug for my first oil change and when I was tightening it back up, it felt like it gave a bit. Wasn't cranking down hard though. I'm hoping it was just the crush washer was canted and I just felt it seating straight. Anyway, it not leaking so I thought I would just go to sucking the oil out in case I did strip the threads. I only ride about 200 miles a year. You think if I lift up the back end I'll get most of the oil out? Any remaining oil can just get diluted with fresh oil every year. Thanks.
@ginatrousdale9555
3 жыл бұрын
Do you have a video of the rebuild of this engine?
@jake2102
5 жыл бұрын
Great video but that wasn’t what the title entailed
@ouber3953
4 жыл бұрын
Where the reassembly videos for the 450 foreman and 400 ?
@jaymiles1929
4 жыл бұрын
I have a Honda Foreman, the problem is that the compression seems too high and the electric starter cannot turn it very easily. Very had to pull start also and there is not compression release I can find. The only way to start it is to hit electric start and pull rope at the same time. Any idea what the problem could be?
@krysmiller5366
4 жыл бұрын
jay miles need to check decompression mechanism
@jameshigbee7003
Жыл бұрын
Just think how much dirt you just introduced into clean areas of the motor that a simple cleaning could have taken care of all of it. What a waste of time
@tjreid1766
3 жыл бұрын
Are the 14 mm head bolts left hand thread??
@snaggletooth1773
2 жыл бұрын
No
@danieljeanson8592
4 жыл бұрын
is he supposed to have oil in the cover of the strator?
@danieljeanson8592
4 жыл бұрын
@@MidNebraskaMotorsportsMaybe there's two models? cause when I removed the cover the oil fell to the ground I removed the drain and all the oil these emptied to the pan! a broken engine base??
@Avalanche2
5 жыл бұрын
10:23 "Will need replaced" Ugh - that bugs the crap out of me.
@NelsonCreekCustoms
6 жыл бұрын
12:10 hahaha push dirt in the motor
@jakedemers1905
5 жыл бұрын
Central powersports do you have an email?
@OGKILLa9365
4 жыл бұрын
1st step degrease and power wash it, then take it apart don't be a noob
@k9cop998
2 жыл бұрын
Why would you not power wash the motor before Tearing it down??? you always always start with a clean motor before you tear it down
@jacobwren6344
3 жыл бұрын
Want to rebuild my 450s ? Nobody around me wants to do it or claims no time.
Пікірлер: 29