Chrome socket on that impact. Mmm you bad boy. Great video!
@JesseBCO18
3 жыл бұрын
Thanks for the video. I just fixed my brakes on a 02 Foreman and this was very helpful.
@Yukon12gauge00buck
11 жыл бұрын
That's for the video. Its nice to know what you are getting into. My rear arm lever isn't pivoting so I have to get into it and clean it. I figure a 12 gauge brush should fit the pin hole. Thx again.
@jasoncarroll944
7 ай бұрын
Thanks mark part 1 And part 2 made my job so easy thanks again
@mckenataylor9777
11 жыл бұрын
Amazing video helped me a lot on fixing the rear brakes on my 95 honda foreman 400
@400EX99N
11 жыл бұрын
i would put a some water proof grease around where the dust cover bolts on ( around the oring mabe replace oring) and make sure the vent hose is good and tight and make sure the end of the hose in up the fram high.your not going to keep all the water out but you can keep most of it. water gets in the most where the pin comes through the back plate where the arm is attached to the cables. make sure that little seal is in good shape and put some grease there.
@amloobrador3519
8 жыл бұрын
i buy a 1997 honda foreman from a atvs shop but was broke down they low the price on it but a stupid person use a hammer to get loss brakes drum and the braket on side for brake cables now im trying to fix it this video help me a lot thanks
@christopherthompson4679
3 жыл бұрын
you do awesome detailed videos!!!thank you so much it was perfect.your an excellent teacher👊🏽💪🏽🔥
@lauraread-mills4193
6 ай бұрын
Working on my foreman atm. Best idea on how to get the pin to release into the neutral place so I can take the brake drum off? I think it's seized
@derekdzuck7231
5 ай бұрын
What size socket after the cotter comes out and does it go clockwise?
@jeffschwarz5706
2 ай бұрын
Great video
@Rowen170
7 жыл бұрын
you mentioned that the brake lever has to be in neutral position in order to get drum off,,I am doing rear brake job this weekend on a 2007 Rancher 420 ,,and I believe it's all rusted/frozen up,,,the cam/pin may not move the lever,,,and my suggestions? ???
@lauraread-mills4193
6 ай бұрын
I'm having the same issue. A long time ago but did you find a way to sort it?
@400EX99N
11 жыл бұрын
@Yukon12gauge just so the break drun can expand a little . if it turns a little red its ok. you can tap the drum a little but not to hard
@400EX99N
12 жыл бұрын
WHAT YOU NEED TO DO IS TAKE THE FOOT BRAKE LEVER OFF THE QUAD. THE POST WELDED TO THE FRAME THAT THE LEVER RIDES ON NEEDS TO BE CLEANED, DIRT & MUD GET IN THERE. TAKE A WIRE BRUSH WHEEL ON A DRILL AND CLEAN THE POST GOOD AND THEN CLEAN THE INSIDE OF THE PEDAL PIVOT. THEN WHEN YOU PUT IT TOGETHER GREASE OR ANTISEIZE THE POST AND LEVER. IT WILL BE HARD TO GET THE LEVER OFF GET SOMR GOOB PENETRATING OIL LIKE PB BLASTER AND KEEP WORKING IT GOOD LUCK AND THANKS FOR WATCHING
@codyt3019
7 жыл бұрын
Do you know what the casted aluminum part is called that holds both the rear brake lines. I have a 1996 honda foreman and I can't find the part that holds the break lines. it broke because a drag used for grading got wrapped up in the rear axle and the break lines, and the chains ripped out the break lines,and broke the casted aluminum that holds the break lines. Thanks for any help.
@jamesradabaugh2562
7 жыл бұрын
Cody T that part is the arm rr brake part number 43410-HM7-000
@TheWolverine-rm2kr
2 жыл бұрын
What do I do if the brake drum won't come off as if it's rusted in place? The brake lever you showed in the video is locked in place also. I soaked it in pb blaster for a day and I even heated it lightly with a propane torch
@400EX99N
2 жыл бұрын
I have been that road. just keep what you are doing, keep using the PB balaster and heat. HEAT the axel by brake drum. light heat wont cut it , and the same for the brake lever
@blake_c_8596
7 жыл бұрын
2015 foreman es- new brakes on but can't get the drum back on. Ebc shoes seem too big??? Any ideas?
@jeremylaurendeau5878
3 жыл бұрын
My brake pas are brand new but still dont brake dont you know what it could be ?
@jamesradabaugh2562
7 жыл бұрын
what will cause the rear brake shoes too disintegrate I put new brake shoes on my Honda Foreman and they are already disintegrated to the metal
@400EX99N
7 жыл бұрын
check your drum, if its not smooth it will chew up the brakes. also it may be the brake shoes them self, like a bad batch or cheap shoes
@arnoni11
8 жыл бұрын
change the seal keep getting water in my drums ordered a new o ring. think that's the issue ? I have a 2014 foreman
@evan.snider
8 жыл бұрын
I am trying to get that bolt off, but it wont budge. I used an impact wrench, but I cant keep the other tire from moving. Any help? Thanks
@400EX99N
8 жыл бұрын
you need heat to the nut then hit it with the impact
@MattMcHugh257
12 жыл бұрын
ok i have a 97 honda foreman 400. and the foot brake lever does not go down unless you stand on it. then you have to use a jack to get it back into place. any suggestions as to what i should do? i got all the pannels off in that area and the cables disconnected. thanks!
@guyg3699
3 жыл бұрын
Can’t the drum off any other Suggestions
@400EX99N
3 жыл бұрын
Make sure the brake cables are all the way off, and use a rubber hammer on the drum to get the dirt off the the inside.
@garypeterson1238
9 жыл бұрын
The nut on the hub assembly isn't a 35 mm. Bought one and it is to big by quite a bit. It is very close to a 1 3/16. My machine is a 2003 would that make a difference and if so could you tell me what else it might be, Thanks
@Randomness6
5 жыл бұрын
30mm
@memesurrectionist5112
2 жыл бұрын
My drum will not go back on. It looks like the metal from the brake shoes has fused to the drum. Is that possible?
@400EX99N
2 жыл бұрын
It can, and sometimes the brakes pads are a little to thick
@Yukon12gauge00buck
11 жыл бұрын
I'm in the middle of this job but the darn brake drum isn't moving. Any suggestions?
@kimilagarrett9706
6 жыл бұрын
I bought a 4 Wheeler and was told it was a Honda Foreman 2000 Model needs a little work. How do i know exactly what Model or size it is before I order parts.
@400EX99N
6 жыл бұрын
GOOGLE the vin number
@brianmikolay6474
6 жыл бұрын
was told i have a 1997 to 1999 honda fourtrax 300 4x4, cant get the right drum, looks very similar to what you have. 8 1/8 outside diameter. 1 1/4 braking surface about 2 1/2 wide. would you help to let me know what type f drum i need to order
Thats what i ordered and its to small www.ebay.com/itm/QUALITY-Rear-Brake-Drum-for-the-1988-2000-Honda-TRX-300-Fourtrax-FW-2x4-4x4/371451593935?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649 and www.ebay.com/itm/Honda-Foreman-or-Rancher-350-400-450-Rear-Brake-Drum-TRX450-TRX350-TRX400-NEW/270865249371?ssPageName=STRK%3AMEBIDX%3AIT&_trksid=p2057872.m2749.l2649 i ordered both of those and neither will fit
@Knowledge-IS-Power365
11 жыл бұрын
Thanks for reminding everyone about the dust. But you should have put more emphasis on the dust. It is very dangerous. It will kill you. DON'T BREATHE THE DUST
@amloobrador3519
8 жыл бұрын
they broke a braket and loss parts the engine sound ok is 4×4 all the time somebody can tell me how much i can selled after fix is a 1997 honda foreman 400cc has a new battery start first time push start an pull start has plenty lights
@400EX99N
10 жыл бұрын
@Cooper Fetterman yes pretty much the same
@GusgusA1
8 жыл бұрын
I need to replace the bearing but someone welded the castle nut on. I'm thinking of cutting it off with a Zip disk how would I fix the threads ?
@400EX99N
8 жыл бұрын
that's a good plan. the threads must be bad that's why they welded the nut
@GusgusA1
8 жыл бұрын
+400EX99N could I use a tap and dye set to clean the nut and threads? I'm new to this.
@400EX99N
8 жыл бұрын
+GusgusA1 you'll have to buy a new nut because you're going to destroy it taking it off. you are going to need a die fix the axle threads
@cooperfetterman5329
10 жыл бұрын
Is it all the same on a 2009 honda foreman es
@tonymartin757
2 жыл бұрын
If the brake cover is tight what is the easy way to remove it screws have been remove
@400EX99N
2 жыл бұрын
There are cut outs on the side of the brake housing, so you can pry off the cover with a screwdriver
@tonymartin757
2 жыл бұрын
@@400EX99N try that but still tight an want move also the brske leaver is hard to move to the release setting
@tonymartin757
2 жыл бұрын
@@400EX99N stiil very tight and the brake leaver want go into the netural postion
@tylermccain9391
8 жыл бұрын
my hub won't come off any suggestions? I got the cotter pin and nut off but it won't move
@400EX99N
8 жыл бұрын
some PB blaster and heat to the hub
@brandonhamrick3491
7 жыл бұрын
Tyler Mccain hey what size did you use to get the center nut off
@brandonhamrick3491
7 жыл бұрын
what size is the center nut you took the cotter pin out of
@matteast2101
6 жыл бұрын
On my foreman 500 2011 it's a 30mm. The brake assembly looks identical to this one.
@Robert_H_Diver
Жыл бұрын
What size socket for the castle nut??
@levicrile7588
Ай бұрын
What size is the axle nut
@400EX99N
Ай бұрын
Should be q 20mm
@bestandroidgame1
8 жыл бұрын
Thanks)
@wklatt4
7 жыл бұрын
Thanks for showing us this!
@davester32
10 жыл бұрын
Is everything pretty much the same with a Foreman TRX450?
@400EX99N
10 жыл бұрын
yes it is all the same
@davester32
10 жыл бұрын
Thanks!
@tonymartin757
2 жыл бұрын
Is it right hand threads for the nut
@markneely8965
2 жыл бұрын
Yes
@brandonhamrick3491
7 жыл бұрын
does any one know what size it is I have a 2011 Honda Rubicon 500fa
@400EX99N
7 жыл бұрын
Brandon Hamrick the nut is 22mm
@400EX99N
11 жыл бұрын
heat and pb blaster (penetrating oil) and just keep working it
@ourtube4u
8 жыл бұрын
I want to know how you got the drum off
@400EX99N
8 жыл бұрын
+ourtube4u first is make sure that the brake cables are all the way loosened. them move the brake arm back and fourth. with the brakes loose slide the brake drum off, it may be necessary to use pb blaster or wd40 between the axle and drum
@ourtube4u
8 жыл бұрын
thanks for the help!
@evan.snider
8 жыл бұрын
is this about the same for a 2004 yamaha big bear 400?
@400EX99N
8 жыл бұрын
+Go Vols 272 YEP pretty muck the same
@evan.snider
8 жыл бұрын
thanks
@jamesradabaugh2562
7 жыл бұрын
yeah that's exactly what they were cheap shoes never going that route again always buy OEM
@Yukon12gauge00buck
11 жыл бұрын
how much heat is too much?
@garypeterson1238
9 жыл бұрын
can anyone tell me what size metric socket is required to remove the nut on the hub assembly and is this a left hand thread?
@400EX99N
9 жыл бұрын
they are right hand threads and this Honda was a 35mm. different models may have different sizes
@garypeterson1238
9 жыл бұрын
400EX99N Thanks a bunch that helps lot.
@aaroedg
9 жыл бұрын
gary peterson i think its a 30 im useing imperial tools so not 100% but 30 is my best guess. i cant get the dang hub off and have no puller....
Пікірлер: 81