Put new bearings in the freezer overnight, they drift into place much easier when fitting. .
@crispernator
6 жыл бұрын
Good video didnt see anything to dramatic that you did wrongly and you saved yourself a heap of money well done .
@michaelwagner2868
2 жыл бұрын
One rear bearing was done after only 24k km on my NC. Thanks again Adrian for your excellent vids, took me an hour to replace the bearings. Did it the first time and was probably a bit too careful, but finally did the job thanks to your excellent explanations :)
@roadbiker8333
2 жыл бұрын
I think it would be better if you use the old bearings to put on top of the new bearings to tap them in. more evenly and less chance of damaging the new one.
@moneyprofessional
4 жыл бұрын
Your advice is good, changed mine in no time. btw the bearings are 6204 2RS front and rear, really cheap standard size (sprocket carrier is different though). Thanks
@AfricaTwin-Stuff
4 жыл бұрын
MoneyProfessional - thanks for posting this info.
@arnaudmoeykens844
4 жыл бұрын
whats the size of the sprocket carrier bearing?
@rpcheesman
Жыл бұрын
Did mine fairly quick after seeing this. Brake side took a beating because water had gotten in somehow and seized the bearing to the wheel. But all good and my rear is smooth as butter now. Many thanks!
@AfricaTwin-Stuff
Жыл бұрын
Always nice having a rear as smooth as butter! 😂
@thiagon7x
5 жыл бұрын
Ao tirar o rolamento, ao invés de bater, aquece a volta dele com um soprador térmico até 120°, e ele sai muito mais fácil Na hora de colocar no lugar, aquece a 120°, e coloca o rolamento no congelador por 3 minutos Isso facilita muito o processo
@Cajva
4 жыл бұрын
I don't even have an NC750, i have a Hornet '03 but it's a pleasure to watch your videos. I'm planning to buy an NC soon.
@AfricaTwin-Stuff
4 жыл бұрын
Thanks mate.
@joghyjobie
6 жыл бұрын
Very well explained. Just like all the other videos it will save me a lot of money.
@luisr980
2 жыл бұрын
Thank you very much Adrian for your videos, they are helping me a lot. They are absolutely excellent, clear, well explained and showing great skill.
@AfricaTwin-Stuff
2 жыл бұрын
Thanks mate. While I don’t advocate anyone “doing what I do”, it’s good to know you enjoy watching them.
@onlinemaster
6 жыл бұрын
I just replaced these bearings yesterday, when replacing the tire :-)
@pedrowurth
Жыл бұрын
Thank you for the video. You saved me 200 dollars.
@TurboDieselBeetle
2 жыл бұрын
another fine job my friend. I appreciate the time you take making all of these and then sharing them with all of us. Though they are very entertaining, I am grateful for your time/efforts in making them. ....and Bob's your Uncle!! :{)
@AfricaTwin-Stuff
2 жыл бұрын
Thank you.
@tomastomas1662
3 жыл бұрын
Thank you, just changed rear wheel bearing
@user-yi9gc1vv8i
6 жыл бұрын
Классное видео!! Спасибо, в России Вас тоже смотрят и благодарят!
@stephen3966
4 жыл бұрын
Always enjoy watching your video. Please keep going. Thanks!
@AfricaTwin-Stuff
4 жыл бұрын
Thanks mate.
@cai11tube
4 жыл бұрын
I was checking my wheel bearing when replacing my worn tyres. It was spinning smoothly in the wheel hub, but I decided to just change since it's been 2 sets of tyre change since the last bearing replacement. After removing the bearing I shake it and it feels like the ball bearings moving about. I took a new one and shake it and they do not have the balls moving around sound. Physical inspection on the old bearing seems fine. All my bearings 2 front and 3 rear all have this balls moving about sound when I shaked them although they were spinning smoothly in the wheel hub
@Tcchan93
6 жыл бұрын
awesome video! i'm planning to buy NC750X 2018 version! good job mate!
@crispernator
4 жыл бұрын
Just something else you might look into and that is a peice of brass bar as a drift i inherited my old mans its just a piece of brass bar that i use to remove wheel bearings on trailers and cars even use it on the head stem bearings on an fj1100 when i owned it anyway just something to ponder .
@pcofranc
2 жыл бұрын
Not a single time was a Greaseolygist consulted. And if I recall, bearings are supposed to be removed with a torque wrench and installed with an impact wrench set to high-torque. The seals on the bearings are supposed to be pried with a dial gauge and the bearings should have been mounted in a lathe and rotated while the grease was installed to ensure a consistent application.
@AfricaTwin-Stuff
2 жыл бұрын
Ha! Yes. Very remiss of me 😢
@VasilisNtikos
6 жыл бұрын
Thank you for this, it will come handy in the future :) Cheers!
@starvaystr
6 жыл бұрын
I gotta buy a house with a garage. 😯
@farmoboy83
4 жыл бұрын
I have a garage spot with a locker but in a open space shared with all the building neighbours. It is a challenge mainly because the lack of light and privacy but i still do all the maintnance on my bikes, even valve adjustments...
@vaseacodrean1060
5 жыл бұрын
Thank you very much!) Really very helpful video😇
@gabrielramireznahim1904
4 жыл бұрын
Buen video. Muy útil. Gracias
@philippebleau4809
4 жыл бұрын
Beautiful scenes from Australia. Wow, what a treat!
@tungym
5 жыл бұрын
thanks so much. very clearly explained
@pcondes
5 жыл бұрын
Hey very usefull stuff!! been watching many of your videos already. It will really help if you can do one on how to remove the left panels (not just the top for the air filter, also really good video). I'm planning on installing an alarm so can use some help there. many thanks for all you have shared.
@cinematictrax8443
Жыл бұрын
The drive sprocket bearing can be purchased from Fowlers Parts UK for £27
@wildone2163
6 жыл бұрын
are all three bearing the same part number?
@PvC63-Jan
4 жыл бұрын
Thx mate, well explained!
@AkaAndyKnuckles
3 жыл бұрын
Well done!
@cinematictrax8443
Жыл бұрын
Am I missing something? The two wheel bearings - no grease cover/s?
@AfricaTwin-Stuff
Жыл бұрын
Are you talking about the bearings behind the sprocket drive ? If so this is normal. Only a grease seal on each exterior side of the wheel. Besides the bearings each have their own grease seal to keep their grease in and gunk out.
@smith3066
5 жыл бұрын
Ничего не понял. Ты выбил подшипник, смазал и обратно поставил?
@vaseacodrean1060
5 жыл бұрын
Новые поставил...
@ihcnarf
6 жыл бұрын
Vert good vidéo again thx
@DirtyTaxman
Жыл бұрын
I noticed you took out the seal on the brake rotor side, but after installation you did not put a new seal back in. You only put a seal on the sprocket side. But maybe you just forgot to show it on the video :)
@AfricaTwin-Stuff
Жыл бұрын
Yes. Just didn’t show it.
@jofrelloreto
3 жыл бұрын
Thanks for the video, I have the same problem. What are ref number of the bearings?
@AfricaTwin-Stuff
3 жыл бұрын
Sorry. Don’t have them. I took the old ones to the local bearing seller and he matched all but one. One is a rare size and has to be purchased from Honda.
@fullyabani
5 жыл бұрын
Hi, I like the way you maintinance on your Honda, could you please tell me dimensions or size of the bearings? I have 2016 nc 750s dct model and I am planing to replace rear wheel bearings.Thank you.
@dashpatito
5 жыл бұрын
The originals are SNK 6204DU
@dk6343
3 жыл бұрын
Please provide bearing brand, size, and part numbers. Thanks
@audrylou290
3 жыл бұрын
Actually bearings of such size costs no big money. Usually I change them with new ones when disassembling any mechanism been in longterm use.
@come2watchya
5 жыл бұрын
Sorry for the dumb question. At the end of your video, you say take the bike to the shop to get the wheel fitted. Can you not remove and put it back on yourself like you show in your other video and tape the adjusters?
@AfricaTwin-Stuff
5 жыл бұрын
come2watchya - I wasn’t clear. What I was saying was “don’t follow my bearing replacement advice, as I’m not a trained professional” !
@come2watchya
5 жыл бұрын
@@AfricaTwin-Stuff Lol. My bad I get it now :)
@MRTPR
6 жыл бұрын
Nice Video Mate
@juse8573
4 жыл бұрын
are the 3 bearings alle the same size and type? Do you reuse the sealing ring? thanks
@AfricaTwin-Stuff
4 жыл бұрын
No - one of the bearings is larger and a weird size. No - the grease seals are replaced at the same time.
@juse8573
4 жыл бұрын
@@AfricaTwin-Stuff the ohne size is a very common one "6204", but the other one is signed as "22x50x15": how did you find this one, which brand?
@AfricaTwin-Stuff
4 жыл бұрын
ju se - purchase the genuine Honda part.
@MrWhothefoxthat
Жыл бұрын
was it just stander purpose grease or high heat, thank you.
@AfricaTwin-Stuff
Жыл бұрын
Standard bearing grease.
@allanbrown3493
6 жыл бұрын
changing bearings already???. Do you use a power washer on your bike?
@ShedBuiltStuff
6 жыл бұрын
Allan Brown - no I don’t. And it lives inside and I’ve only ridden in the rain a couple of times over the 38,000km.
@pjp967
Жыл бұрын
what kind of grease do you use?
@AfricaTwin-Stuff
Жыл бұрын
“Bearing grease” bought from car parts store.
@alexthebear
5 жыл бұрын
Good job! How much Km or Miles you did before change?
@AfricaTwin-Stuff
5 жыл бұрын
BearScience-ru - can’t remember exactly. It was around 35,000km
@farmoboy83
4 жыл бұрын
@@AfricaTwin-Stuff they should have lasted longer...60000km on a sh300i with original bearings...
@kislyjdozhdik
3 жыл бұрын
@@farmoboy83 have lightly over 40t and have to do now
@kislyjdozhdik
6 жыл бұрын
thanks :)
@ricardoanis5359
5 жыл бұрын
muy buenos videos , podrias subtitular en castellano?
@robsonenduro3316
6 жыл бұрын
hi, great job. At honda they're pretty expensive, can you share thees bearings part number?
@remigiuszbulski5645
4 жыл бұрын
6204UU
@arnaudmoeykens844
4 жыл бұрын
@@remigiuszbulski5645 and are they all three the same?
@davidaidan2128
Жыл бұрын
Hi very good as usual ! Could u please provide me the reference for the last bearing linked to the chain mechanism. Honda reference is 91051 mgs d31 but it's very expensive. I Found a reference in internet 62-22-2rs c3 far cheaper but I have some doubt since it's an angular bearing not like the others... please could u help me...Honda price is almost 60 EUR... regards
@AfricaTwin-Stuff
Жыл бұрын
Sorry. Don’t know. The odd size bearing I could not get from the bearing supplier. I wasn’t going to pay for a Honda one. But the bearing supplier had a stock size that was 1mm narrower and I have used that with no I’ll effects.
@davidaidan2128
Жыл бұрын
Hi I think I found as u a bearing narrower 1mm the reference I gave u. I will try it... Honda is very expensive for equivalent quality as SDK brand which is less expensive... Regards
@davidaidan2128
Жыл бұрын
Hi last question please...since u changed the 3 bearings Did I notice please that the specific bearing related to the chain was different ? I mean not regarding the sizes but the type of bearing itself?...it's written for this one "angular" not like the others... regards
@AfricaTwin-Stuff
Жыл бұрын
All the bearing I replaced were plain roller bearings of the same type.
How many kms when bearings needed changing? thanks
@Bilas442
6 жыл бұрын
I need a answer, also... Thx!
@AfricaTwin-Stuff
6 жыл бұрын
My bike has done 38,000km. But bearings only need replacing when they are worn. So check you wheels from time to time and if you see/feel movement, replace.
@spudcoat
6 жыл бұрын
Thanks, I am currently only researching what bike is best for me, and the Nc750x has been looking good up to now. I can see that you are a careful rider and wouldn't push your bike to its limits, but a wheel bearing wearing so quickly isn't a good sign. it isn't what I would expect from a Honda.
@AfricaTwin-Stuff
6 жыл бұрын
spudcoat - then again, $16 for a wheel bearing after 2.5 years and 38,000km isn’t a worry as far as I’m concerned
@spudcoat
6 жыл бұрын
Fair enough, but still surprised at that problem arising at that mileage. I have just googled that very problem on the NC750 and its a common fault, so far I have read that some owners had rear wheel bearings done twice, one had them done under warranty at 13k miles (20k kms) then again at 23k miles (37k kms). It seems wheel bearings don't last as long as the chain. Maybe cheap at $16, but the ease of maintenance on the NC750 seems to have become less easier.
@cajunrider7101
6 жыл бұрын
Too soon to need a new bearing. What caused this ?
@AfricaTwin-Stuff
6 жыл бұрын
Cajun Rider - no idea mate. If anyone can suggest a way to diagnose bearing failure I’d love to know. It had plenty of grease in it when I inspected it and no signs of water ingress. By the way, what kilometres should bearings wear out?
@wyjebiozanamaksa1616
5 жыл бұрын
My suzuki gn 125 needed new bearings at 10k miles, i got it last year with 6k miles and its from 2003 so notice it was sitting a lot
@SuperMegaSammy
4 жыл бұрын
And sometimes use of high pressure water jet cleaning the tires are cause of early failure too.
@johncummins3860
2 жыл бұрын
Too tight chain tension ruined sprocket side - go 5mm more than manufacturers guide! !
@bigwheelsturning
6 жыл бұрын
Don't like the way you put the new bearings in. Find the correct socket that fits the "outer rim" of the bearing. Never tap on the race cover, or inner race.
@AfricaTwin-Stuff
6 жыл бұрын
bigwheelsturning - yes you are correct of course. Notice I said NOT to follow my method!
@Dontgetenslaved
Жыл бұрын
Just got mine done. It wasn't that bad, the main sprockets came out fairly quick. Just a pain to hook onto the first bearing in the wheel but the second is super easy. The hub bearing requires flat out beating to get out. All are fairly easy to get back in if you put the rim between something that's level so you get it straightened out and not go in crooked.
Пікірлер: 109