I would have power washed everything before i put the plastics back on lol good job sir!
@jimsimpson4385
5 жыл бұрын
why did you not ajust the valves with a fuel test bottle before asbly? Also i did not see you ck the face of the valve stim to be true and not diminished or cupped from the tappet strikes of normal running?
@troycrowder9942
5 жыл бұрын
hey that muffler pipe never makes it in there the first try mine is a 02 just finished doing the top end your video is spot on and a great reference
@jasonwilliams2852
3 жыл бұрын
Im sorry for asking here but what are the part numbers for the dowels that you placed in that the rocker arm mount sits on? I was watching your video and doing this myself to simpily clean my piston and I lost the dowel. I cannot find it anywhere although I do have the other dowel. Please respond if you are able to and thank you in advance! (Before you send me to the website i have attempted to find it there but i cannot seem to determine which it is)
@cassiemoore622
3 жыл бұрын
I need to know the size of the rocker arm retaining bolt please
@rickypadron875
6 жыл бұрын
+partzilla since I got new gaskets would I need gasket sealant for the top and middle gasket or the bottom one as well.
@lancelong1696
6 жыл бұрын
what about timing.. I don't think I ever seen you put the motor back in time? or is that what you did when pulled the back up starter all the way too the very yop
@lancelong1696
6 жыл бұрын
*top
@PartzillaParts
6 жыл бұрын
We didn't have to adjust timing, Just bring it back to TDC when you install the piston.
@lancelong1696
6 жыл бұрын
Could y'all do a video own how to replace the timing chain
@PartzillaParts
6 жыл бұрын
We'll add it to the suggestion list!
@mattbudd3403
7 жыл бұрын
Sounds like it’s got a valve tick
@PartzillaParts
7 жыл бұрын
Matt Budd Very good ear! The valve adjustment video is in process. Should be live next week.
@mattbudd3403
7 жыл бұрын
Partzilla sweet now when I adjust the valves on my 300ex should I do it when the engine is warm or when the engine is cold?
@PartzillaParts
7 жыл бұрын
Honda manual says check them when the engine is cold.
@cadenlouque
4 жыл бұрын
What is the little rubber o ring for ?
@michaelmassey733
Жыл бұрын
spacing to prevent friction wear over time i could imagine, don't quote me on it tho lol.
@GB-hk9ou
4 жыл бұрын
What causes dry smoke on startup and when accelerating after it idles for a few minutes.
@GB-hk9ou
4 жыл бұрын
Note: it’s not a steady smoke and it doesn’t smoke noticeably when riding. Just puffs at start up and acceleration after idling
@silverfoxslash
3 жыл бұрын
Valve stem seals?
@vintagescoutingoutdoors9096
4 жыл бұрын
Shouldn't you compression test before first start?
@lotuscampbell8660
4 жыл бұрын
gives u a good idea of whats going wrong and to see how much you improved.
@philipgagne1852
3 жыл бұрын
Until the bike is ran for a while the rings won't b fully seated and compression will still show on the lower side usually so it's not needed to test till after a few rides
@NelsonCreekCustoms
6 жыл бұрын
Hey my head stud it stripped at the top ( the long bolts the come out of motor ) it got the stud out but how should I get the new stud in HELP!
@PartzillaParts
6 жыл бұрын
Threads were stripped only at the top and not the bottom? You would just have to screw in new studs into the crankcase. You can double nut the top thread and wrench it down that way.
@NelsonCreekCustoms
6 жыл бұрын
Partzilla thanks I was thinking of that but I though it would be to much pressure in the small area and stripped threads again but you have experience and I don't so I'll do that
@NelsonCreekCustoms
6 жыл бұрын
Partzilla also... how much would it cost to have the cylinder bored same as you did? Would it be cheaper to get a new cylinder vs getting it bored
@PartzillaParts
6 жыл бұрын
Depends on the shop. Usually, it's cheaper to bore out than it is to buy a new one.
@saltywat3r6.0
4 ай бұрын
Is ticking normal when u first run it after the rebuild?
@alaskan49thstate29
6 жыл бұрын
only if you were here in Chevak,AK 99563 so you can teach me how to fix any kind of Honda. now I can not wait to fix up my top end engine it's a trx350fm 2006 Honda rancher 4x4 I think I'm going to spend about $1,000 to be fully functioning and more power I noticed I'm starting to lose power I will need new parts and your video help me out with what I need to do thank you very much.
@vintagescoutingoutdoors9096
4 жыл бұрын
Do the bottom 10mm air box bolt first. It saves alot of screwing around if the air box is free.
@chadillac_256
4 жыл бұрын
Dan Fraser make your own video bud
@josephbaccili6407
8 ай бұрын
how long do you have to run it for to break it in?
@chadillac_256
4 жыл бұрын
Thx man Great video I bet there’s a lot of motorcycle mechanics mad at you 😂 you’ve already taught me a lot and saved me some 💰 thx
@hcastilla2010
4 жыл бұрын
Hi I have a 2000 rancher 350 and I noticed some oil residue between the valve cover and head, I know its the gasket between the two. So I am planning on replacing it soon, because of this I checked the compression on the cylinder and it is giving me 52 psi, which I dont think its accurate, the atv runs great, doesnt smoke, nothing to tell me there might be something wrong with it. So I did a wet compression test and it stayed the same at 52 psi, so now I am wondering if it could be something with valves? any suggestions? thanks
@douglaswhitting3469
2 жыл бұрын
I have a 2003 Honda rancher 350es I would like to know how do I install the bypass for the electric shift
@leandrodosreisvilela4807
Жыл бұрын
Shoowwww... tooopppp
@johnny_k3575
5 жыл бұрын
After all the work you have done you didn't check the compression again to see how many ponds you getting !!!
@jeremyrue9335
3 жыл бұрын
This is a Question , I have a Honda 2005 TRX350 ES , When I purchased the bike it was locked up , I pulled the head And Cylinder , the piston and the pin was faulty , I installed a new piston and pin put back together set the Valves on TDC .06 INSTALLED a new carberator and check the plug for firing 🔥 but it would not start any help would be appreciated...
@TLark
Жыл бұрын
Check to see if the atv has spark and if so put some quick start spray in the carb and try firing it up
@cassiemoore622
3 жыл бұрын
I need to know the size of the rocker arm retaining bolt please
@tengranido6188
7 жыл бұрын
how about valve adjustment
@PartzillaParts
7 жыл бұрын
In the works!
@euros_tc5714
4 жыл бұрын
And all this is done without any gasket maker??
@redetroitwing
3 жыл бұрын
What's this cost at a shop?
@chriseskue4286
4 жыл бұрын
very very helpfull thank you
@laroybubba2050
6 жыл бұрын
Thanks for the videos! I have completed the rebuild as described in the 4 videos, but now I have smoke after the engine is warm. Any suggestions? Rings not seated properly or Valve Seals maybe?
@NelsonCreekCustoms
6 жыл бұрын
LaRoy Bubba did you check your connecting rod for up and down slack? Is there knocking? It's normal for some to smoke until rings are fully seated. It could also be oil in your exhaust from before you rebuilt it just burning out ( that's common ) did order your parts from partzilla or did you get a cheap kit off eBay?
@NelsonCreekCustoms
6 жыл бұрын
LaRoy Bubba one more question! Does it smoke when its running without you giving it gas
@laroybubba2050
6 жыл бұрын
EaZier Clutch EaZier, sorry for the delay. I did check for slack on the connecting rod, it seems solid, no sign of any knocking. I also rechecked the valve adjustment, it still looks good. To answer your last question; it starts much easier than before (typical Honda) idles for 3-5 minutes with no smoke at all. After warm and riding a little it smokes while riding and also at idle. I didn’t want to ride it too much for fear of having a ring not just right. Thanks again for the help!
@vintagescoutingoutdoors9096
4 жыл бұрын
Your ring gap ends are lining up. Maybe wiggling in the jug they moved?
Пікірлер: 51