Thanks for your video my friend I've a Honda SH 125cc 2022 in two months time, But your video I think is a great help, 👍 Kind Regards James Fae (from) Scotland 🏴 Part of the uk 🇬🇧 😊 👍
@rossmoore2844
10 жыл бұрын
Thank you for this very helpful video! I now know how the transmission works, and how to repair it. Excellent video!
@yusifradder5967
5 жыл бұрын
Thanks for your advice. I managed to get the clutch bell out with the help of a claws like gear puller, cost me about £15:00. The problem was caused by over tightening the nut with an impact French which has cause a damage to the end surface of the bell after the teeth the hold the spline together. It has also caused the little tube in the inner bearing of the driven face to have a little ware. All has being replaced now. I have learned my lessons.
@tinhd81
9 жыл бұрын
Thanks for the post - 2nd belt on this bad boy (30,331 miles just blew today...kekeke) but I'm gonna save alot of $$$$ Thanks Again
@neilpinkett
6 жыл бұрын
many thanks... my rollers were nearly square. :)
@darthemma
10 жыл бұрын
The stock roller weights in the SH150i are 20x15 and weigh 12.25g (when new).
@tasulis
8 жыл бұрын
+darthemma for Sh 150 2013-14??
@danpullin6610
2 жыл бұрын
13.5 grams be allright for highway use?
@smelroygibson5174
4 жыл бұрын
Thanks for the insightful video. Could you please tell me what weight rolllers come stock with 2010 sh150i.
@jamescarey7277
4 жыл бұрын
Hello, thanks for the videos,great job. I am in Ontario Canada and need to get a new variator ( both covers are worn), do you have a supplier that can ship to Canada? I have a new belt, can I run with the worn variators? Thanks Jim
@sloopkogel9463
9 жыл бұрын
Thanks for sharing!
@apostolosnoulas9941
9 жыл бұрын
Thanks for sharing
@yusifradder5967
5 жыл бұрын
Hi DaBinChe, Can you help? I have a problem with the clutch bell not coming off after removing the nut.I was about to change the belt and clean the whole crank case for inspection . It's pretty strange why the bell is stock.
@DaBinChe
5 жыл бұрын
could be that the spline between shaft and bell is mangled
@yusifradder5967
4 жыл бұрын
Hi Friend, My Sh is about 33,000 miles now. I am experiencing an uneven were on inner and outer drive faces. The is riding fine but I will like to asked if this is going to cause any serious problems. The ware is about 1mm deep. Your advice will be greatly appreciated.
@DaBinChe
4 жыл бұрын
the inner and outer drive face needs to be replace. Both are aluminum, best to replace them at the same time as the rollers and belt. Stock my SH150i top speed is 75mph indicated. As the drive wears the top speed will drop. Once tops speed is down 5mph I know it is time to replace all those drive parts.
@RAMEmotosertaodocariri
Жыл бұрын
Muito bom
@jamesh8001
9 жыл бұрын
Great video. I want to change the belt and rollers on a honda ps 125 I think this is the same engine. Can you help?
@DaBinChe
9 жыл бұрын
James H PS and SH hould be very similar
@pops5663
4 жыл бұрын
Quick question i have to put a new front brake caliper in. When I Remove the brake line will it leak out fluid? If so where do I put brake fluid at?
@DaBinChe
4 жыл бұрын
why need new caliper? damaged? Yes fluid will come out. You'll need new sealing washers (two) at the end of the brake line, one on each side of the Banjo bolts. After reinstall you need to do a brake bleed.
@pops5663
4 жыл бұрын
Yes bad caliber I cant get pins out that hold brake pads. The screws are stripped but I have new caliber and will install but just wanted to see if you know where location is to refill brake fluid if it’s low?
@DaBinChe
4 жыл бұрын
@@pops5663 I have a brake bleed video for the sh150, look in the playlist for sh150. As for the two screw that hold in the pad retainer pins try hitting them with a ball peen hammer first
@brasileirandoporai7875
4 жыл бұрын
Hi Dabinche. Where is the Honda Elite 110c?
@DaBinChe
4 жыл бұрын
Not sure what you are asking....for that video go to my channel under playlist you will find one for the Elite110. If you are asking what happened to my Elite110 I am on the second one the first one was sold to a friend
@passantenicola
10 жыл бұрын
hello how is called the key greetings
@randalldixon5024
4 жыл бұрын
My variator tool prongs are too big. Do you have the specs and supplier for the variator tool?
@DaBinChe
4 жыл бұрын
sand/file/dremel them smaller in diameter. A drill works too with a dremel attachment. I had to do that with mine too
@randalldixon5024
4 жыл бұрын
DaBinChe Thank you so much! Any videos on rear clutch removal? Thanks for your videos they are a great help?
@DaBinChe
4 жыл бұрын
@@randalldixon5024 Not one for the SH but I do have one for the NHX110 which is basically the same setup
Пікірлер: 34