You need to remove the cassette and fix the green seal into place, hope do have a tool to make it easier but you can do without, plastic tyre levers are good for this,no metal sharp edges. I’d pop a bit of wet chain lube in the ratchet ring to keep it sweet also I’ve used the dt grease on the pawl and spring seats to keep them moving. Still working as should? Atb John 🏴
@ignatiustremor
Ай бұрын
Damn dude, these free hub guts look like you send the rear wheel diving and left it for good 😲
@StevenHandDH
Ай бұрын
Do what we do 😂
@user-gs5wo4ec3j
5 күн бұрын
Aaaah the Pressure Washer club.
@edgarsnezinu1439
Ай бұрын
Well it could happen if you do a lot of pressure washing .. I would recommend to take off cassette and double check on green seal maybe it was off some point .. Really shocked to see so rusty inside they are on market maybe 6 months only
@MrSzwarz
2 ай бұрын
It has never been serviced, with no grease, no cleaning. Water got inside and corroded all parts. I service my DT Swiss freewheel every second month! It takes few minutes same some special light grease.
@StevenHandDH
2 ай бұрын
It’s not even six months old, Shouldn’t be like this already
@123dwd
2 ай бұрын
the way you pressed the freehub on, already attached to the cassette- you have no way to push the green seal into place. it needs to seal up against the hub body. it is a simple push into place but with the cassette attached you cant push on it.
@StevenHandDH
2 ай бұрын
I didn’t have a chain whip at the time, I’ll place the seal on tomorrow as I’m borrowing one off a friend. Appreciate you though, Thanks for the heads up 🙌🙌
@123dwd
2 ай бұрын
@@StevenHandDH right on! nice work, it cleaned up real nice
@StevenHandDH
2 ай бұрын
It got there in the end, NIghtmare. Thought it was a goner haha @@123dwd
@zeez4178
2 ай бұрын
@@StevenHandDHmake one from an old chain !
@StevenHandDH
2 ай бұрын
@@zeez4178I have bought one now 🙌🙌
@jamesmincher3435
2 ай бұрын
Just needs good clean and grease the springs look better quality compared to the pro4/3/2 stronger and longer lasting i cant wait to get pro 5 one day😊
@StevenHandDH
2 ай бұрын
All done & dusted
@nicholascowen
2 ай бұрын
I think you need to get some grease on the free hub paws. I had a similar issue with a vel hub that has actually rusted onto the spindle. There was no grease in there at all. Also didn’t have a serviceable hub so I ended up having to by a new freehub for it.
@StevenHandDH
2 ай бұрын
Cheer, Just do not understand how its washed the old grease out though? Absolutely melted my head trying to figure it out. I am sure the seal has popped out and then water got inside.. Back to normal now anyway!
@nicholascowen
2 ай бұрын
@@StevenHandDH in my case it wasn’t helped by being in a humid environment when it had been wet. Maybe the back of your van and the temperature of the vehicle could have done it.
@StevenHandDH
2 ай бұрын
I would say your not wrong, Just surprised me how the actual grease had been washed out. Going to put more inside it I think
@Fosgen
26 күн бұрын
Aluminium rusts too, just bit lower pace than steel. Stainless steel is best at resisting outdoors.
@KiteWaldi
2 ай бұрын
There should be grease inside
@StevenHandDH
2 ай бұрын
I just do not understand where its gone though? I am sure the seal has moved or come off and water has gotten inside while the wheel was turning and washed it out. Absolutely baffled me
Пікірлер: 28