thank you so much for posting this I had got to the point where i knew I had to remove the fan but couldn't see how the fan came off.
@KevinFord-y2y
Ай бұрын
Absolutely brilliant. Like you say there are lots of videos but none seemed to be of exactly the model that I had. As a DIY person I'm at the Chuckle Brother level so was unsure of whether to even attempt this but a replacement belt at £13.50 as compared to a new machine at £250 + forced my hand. Without your video I'd have given up, so thank you so much.
@simonwaite125
4 ай бұрын
😀Thank you. I had managed to get as far as the fan but your video confirmed that it was just a nut that needed unscrewing. It might help others to know that I used a 10mm socket on the nut, but space was tight, so i removed a couple of screws from the back panel immediately behind the fan to give me a few mm of extra space.
@drinkslee
21 күн бұрын
Excellent brilliant the only video I have found on this I was confused how to get it on until I found this video thanks 🙏
@xOLD-MAN-GAMINGx
5 ай бұрын
You're a legend mate, Got the belt round the drum but as you say all youtube vids the fan is the other way around, and this models looks like there is no where to go , you just saved me lots of problems Appreciated Ty very much
@iansutton996
6 ай бұрын
Thank you !! Massive help. All became clear after watching this. Cheers
@stevetong1576
7 ай бұрын
Oh for the love of the…I wish I’d watched this one. Managed to wiggle the belt over the back fan and through the shaft seal but the pulley was just impossible. Didn’t realise what the spring did until by chance and that it’s a self adjusting mechanism. Thank you. Happy wife now.
@user-kf3zc8sz3g
8 ай бұрын
Thanks for the video, my model is the same and didn’t match other videos layout, i.e. motor the other way round, very helpful.
@kool4caats
8 ай бұрын
Thanks for posting this. It saved us a lot of time and frustration.
@Tutankhal
2 ай бұрын
If you remove the black cover both sides it comes out easily, you can clean out the dust in the front fan at the same time and no need to remove the nut from the rear fan. The belt goes around the grooved part of the spindle, and passes in front of the tensioning pulley - it’s easiest if you do it with the spring off then can use the mechanism to tension by hand while revolving the drum upwards, so the belt aligns properly before reattaching the spring.
@kierenwalsh6071
8 ай бұрын
Thank you for posting this video. I was at the point of calling out an engineer.
@skyskieskie
6 ай бұрын
you hero !
@Andy-jy3fs
3 ай бұрын
There is no need to remove the white fan. Slip the belt around it first and then up over the rear side of the drum.
@giorno5754
5 ай бұрын
I have a problem with the spring part. Were do you need too place that?
@user-gr4jw2ld1g
6 ай бұрын
How do you put the spring back on
@kevinleigh9292
8 ай бұрын
How did you remove the black cover?
@iansutton996
6 ай бұрын
Looks like a lot of belts all breaking around the same time.
@user-qe2dg5wn3x
9 ай бұрын
How did you get the belt to be tight over the pulley as I can not find any videos on it
@politicalcorrectionfacilit2644
9 ай бұрын
I've got the same problem. I'd figured out how to get the fan off and loop the belt on but because I don't know what the belt placement looked like I'm not certain which way round I'm supposed wrap it round the other spinny thing. So my belt is either too loose or too tight. I bought the 2010mm belt. Did you sort yours out? Thanks
@user-kf3zc8sz3g
8 ай бұрын
@@politicalcorrectionfacilit2644 I’m sure you’re sorted by now, I’ve just replaced my belt. This motor is tensioned with a big spring, so when looping the belt over the spindle and roller you just need to push the motor upwards, which gives enough space, when you release the motor it tensions the belt.
@politicalcorrectionfacilit2644
8 ай бұрын
@@user-kf3zc8sz3g thanks. Yes I got there after a lot of staring and figuring then brute strength 😄.
Пікірлер: 21