Great animation! I wish I could have this skills. It is not clearly shown how the pistol let the same amount of gas flowing for every compression of the trigger. 💪🏼💪🏼 Great job
@STONECOLDET944
3 ай бұрын
So all you have to do to over clock it is replace the bolt action spring then add in a massiveley over pressurised PCP tank
@OldNavajoTricks
2 ай бұрын
Folks have indeed modded the fk out of this platform, including hpa modification.
@Kiwikiwi124
Жыл бұрын
Im planning to make one of this but sniper this was really helpfull
@1ZEEDEE
Жыл бұрын
This is cross section is great. Thanks for making this.
@geoffankrett7012
3 ай бұрын
Great video 👍
@007tallguy
Жыл бұрын
That's a very informative graphic! 👍👍
@travelcompass591
8 ай бұрын
Very didactic animation. I have a CO2 pistol but I did not know how it worked., thank you :-)
@dianadjiemunaji9291
3 ай бұрын
saya ada senapan gas seperti ini .hanya seal ujung gas nya yg perlu diganti.
@vasilysh2795
20 күн бұрын
Пружину не нужно менять? Я поставил тугую, но не знаю нужно ли было
@danigarcia9418
4 ай бұрын
Un vídeo del m25 mostrando mecanismo interno maestro, por favor!! 👏🏻👍🏻
@nelamyselma2920
4 ай бұрын
Gd mrning mam sir.pwide tyo mka bile.mgkano yan .intresado po ako bomile.
@UtopianWebsurfer
18 сағат бұрын
It probably costs between $20-$50 dollars. That looks a single shot gun .17 caliber. The power of the gun, can b GREATLY Increased, just by boring out the long internal gun firing shaft, from end 2 end evenly, so as to be 1/4 inch internal diameter of the internal gun firing shaft, but still use .17 caliber bullets, & the gun will be a fatal weapon, b cüZzZ the bullet isnt impeaded as its fired, & the speed of the bullet will reach speeds of 1,000-2,000 f.p.s.(feet per second) terminal velocity. Any machine shop with a good table top drill can dü this using long Carbide drill bits & either used motor oil, or water soluble machine shop oil, when drillings out the shaft using a long 1/4 inch bit, the length of the internal shaft of the gun.
@AirGunMech
18 сағат бұрын
@@UtopianWebsurfer wonderful suggestion
@abengtebaran5346
Жыл бұрын
The most awesome lovely beautiful air pistol ever built ,how much does it cost can it be ordered on line .😮😮😮😮😮😳😳😳👍😎
@AirGunMech
Жыл бұрын
In which country do you live
@adamnugraha7098
22 күн бұрын
Pake shock apa itu om
@KamTava
4 ай бұрын
How much is it?
@NurWahyudi07
10 күн бұрын
Saya punya senapan gas seperti itu akan tetapi setiap mau gabti gas seal seal karet juga harus diganti karena cepat keras karena dinginnya gas
@RamKumarVerma-r1r
28 күн бұрын
How much
@Hunterdetectorismo
11 ай бұрын
Obg eu nunca tinha entendido o funcionamento mas agora é muito claro obg
@Spongebobber463
7 ай бұрын
I wanna try to like make a shotgun shell with like monkey noodle bits I can make with like co2 which will like blast a hundredof tiny monkey noodles through a light amount of tape that keeps it in the shell but I’m not an engineer so I have no clue how that would work
@BinhGold-zx2ki
2 ай бұрын
loại như này giá bao nhiêu vậy ❤❤❤
@dalehenderson6148
4 ай бұрын
Now to put it in an rc plane
@iamnotaherobrittanyriley2896
Жыл бұрын
没有声音啊
@ashlee896
Жыл бұрын
Can you do a break barrel
@parvanalexandru4041
3 ай бұрын
My neck hurts
@HidayatYat-h6t
4 ай бұрын
Apakah ini sdh di jual bebas
@AirGunMech
4 ай бұрын
No
@FranciscoCane-oh6xj
11 ай бұрын
magkono po ba mam/sir
@VanThanhNguyen-mu5ot
4 күн бұрын
Tôi rất thít nó
@ronilogumahin3759
9 ай бұрын
From Philippines
@شهریارپزشکنیا
4 күн бұрын
ویدیویی که مکانیسم وجزییات رو نشون میده لطفا
@jp1764
10 ай бұрын
J ai un pb de cp1 m. La cartouche est bien percée. La détente fonctionne aussi mais la pression de co2 ne se transmet pas au plomb. Quelqu'un peut m aider?
@AirGunMech
10 ай бұрын
There are 7 O-rings in the pistol. You have to check all of them and change the damage o-ring.
@VINODHT-q8e
7 ай бұрын
Exllent
@MbahDoelMilyuner
5 ай бұрын
👍👍👍👍
@jeanmaicon5776
2 ай бұрын
Tudo que eu precisava saber
@ricardopereyra1802
11 ай бұрын
Hm
@yohanesayen8233
6 ай бұрын
Halo Pak Harganya brapa ya tks bisa Minta No tlp Bapak
Пікірлер: 54