Amazing man! Makes me wish Ford did it that way from the factory I want mine to be like yours!
@RogerBuckChrist
4 жыл бұрын
Thanks!
@mgt5009
Жыл бұрын
This might only have to get done if a 20” is used. But all this actually isn’t necessary, especially removing and cutting things. I run a +54 or 55 18x11 forgestar f14 with MT ss 345/35/18. All I had to do is smack the inner well a bit with a auto body dolly. Tires will stick out 3/16”, if you really play with your pan hard bar you can get it less. Not a big deal and barely noticeable. Also if anyone is wondering, a 345 on a 11” barely bulges, maybe a 1/4” on each side. Just my experience. Car is a 08 GT500
@darrenharris2978
3 жыл бұрын
Running those tires on stock height 09 Shelby gt 500 super snake 🐍 345 -30-20 zr nitto have 20/11 inch rim
@RogerBuckChrist
3 жыл бұрын
Nittos are narrower then Michelin
@jbaker7134
3 жыл бұрын
Did you have to clearance the inner fender on that 09, like relocate bump stocks & the brackets, etc...???
@DELOMUSIK
3 ай бұрын
Could I use 1.5in spacers to make them fit?
@jbaker7134
3 жыл бұрын
I'm about to widen my 2013 rims to 11.5 - 11.75... In part to keep the OEM offset in tact. Bumpstop relocation etc.. in the works too.. It looks good, but was the spacer necessary? Were you still rubbing the inner fender after all the cleanup you did there?
@RogerBuckChrist
3 жыл бұрын
I was OK with 325s and 335s, but when I went to 345s it was just too close to the inner fender. I had lots of room to push them out after the flare so I added the spacer
@CU-gf7yi
12 күн бұрын
Looks good but the stock rims look better
@tomkjr1
4 жыл бұрын
Those 345s are HUGE!!
@RogerBuckChrist
4 жыл бұрын
I forgot to mention they measure 13.5" wide in my video
@tomkjr1
4 жыл бұрын
@@RogerBuckChrist That's some serious traction. You'll need it with that big whipple! Have you run any dyno numbers with it yet?
@RogerBuckChrist
4 жыл бұрын
@@tomkjr1 not yet...my tuner is 4 hours away and we aren't travelling yet
@tomkjr1
4 жыл бұрын
@@RogerBuckChrist If you don't mind me asking, where are you located? I need a good tuner too, but I'm in NJ.
@RogerBuckChrist
4 жыл бұрын
I'm in Ontario,Canada....I have to go to toronto to get it tuned
@peterscott2097
8 ай бұрын
Hope all is well the 345s look amazing on that car .. Iam interested in using wellcraft to do the same with my alchoa wheels what was the cost an do recommend them ,have you had any issues with the wheels such as them being out of balance Thanks ….
@RogerBuckChrist
8 ай бұрын
I had no issue with the wheels being hard to balance or having vibration issues. I have been 258km/h on them no problems. I can't comment on cost due to me having it done about 6 years ago and having to ship them from Canada, which was a pain
@peterscott2097
8 ай бұрын
@@RogerBuckChrist ok thank you very much for you reply..
@fdyjt
Жыл бұрын
is it allowed in the states to have your tires out of the car ? or they need to be inside/equal to the car thing sorry my englisch
@RogerBuckChrist
Жыл бұрын
They can stick out a little bit. I'm in Canada
@Phuong_Nguyen_
3 жыл бұрын
Can you still break traction on hard launches?
@RogerBuckChrist
3 жыл бұрын
Yes, i can roast them if i really wanted to
@Phuong_Nguyen_
3 жыл бұрын
@@RogerBuckChrist without tapping on your brakes?
@dmvtorqueboost1013
3 жыл бұрын
do you perform your service for a fee
@RogerBuckChrist
3 жыл бұрын
It was done at my buddy's body shop, so yes
@dmvtorqueboost1013
3 жыл бұрын
@@RogerBuckChrist good evening where is your chop located and what is the cost to do the panels
@RogerBuckChrist
3 жыл бұрын
@@dmvtorqueboost1013 shop is in north bay, ontario canada
@dmvtorqueboost1013
3 жыл бұрын
@@RogerBuckChrist good morning what is your cost to flair my quarter panels like your friends
@dmvtorqueboost1013
3 жыл бұрын
@@RogerBuckChrist thank you
@mrdh927
Жыл бұрын
Does it fit the factory rims?
@RogerBuckChrist
Жыл бұрын
No, must be 11.5 or wider
@justin-sane713
2 жыл бұрын
Did you have to paint when you did the wheel flaring? If not, how did you do it?
@RogerBuckChrist
2 жыл бұрын
I was getting the whole car painted, so we flared the fenders before paint.
@justin-sane713
2 жыл бұрын
Thanks for the quick reply! I’m looking at bigger wheels just wanting to make the right moves at the right times and not go backwards! Thanks again for the great video. The car looks great!
@TheTAquino
4 жыл бұрын
Sick car man! You got instagram?
@RogerBuckChrist
4 жыл бұрын
@rogerbuckchrist
@stangedude5646
9 ай бұрын
Why the he'll would you want a wheel that big????
@loloforge2841
3 жыл бұрын
How did you flare out those quarter panels? They look perfect!!!
@RogerBuckChrist
3 жыл бұрын
We used a fender rolling tool
@loloforge2841
3 жыл бұрын
Really? You always have videos, no videos for that? Looks like body work to me!!
@RogerBuckChrist
3 жыл бұрын
@@loloforge2841 lol it's hard to keep a secret if you video it
@loloforge2841
3 жыл бұрын
I understand man. No problem. That’s exactly what I thought!! It’s way to perfect. Just perfect. I’m working with a guy in Miami to do it as well. My car just has no traction.
@Phuong_Nguyen_
2 жыл бұрын
Sorry if I missed it in the video but what are the fronts ?
@RogerBuckChrist
2 жыл бұрын
I didn't mention the fronts. They are 20x9s with 265/35R20s
@Phuong_Nguyen_
2 жыл бұрын
@@RogerBuckChrist did you make a video about how you flared the fender? With just a roller?
@RogerBuckChrist
2 жыл бұрын
@@Phuong_Nguyen_ no I didn't show how....but we just used a fender roller.
Пікірлер: 51