Gonna be doing a very similar setup but with a sidewinder manifold. Lucky for me I tig weld for a living so all the fab work I can do at home. Clean build though man Enjoy it
@CarolinaTunerCultureCTC
Жыл бұрын
Very informative!!! Good job
@adamyang8815
Жыл бұрын
Yo I love your content so much keep it uppp 🔥🔥
@oemworx4147
Жыл бұрын
Thank you!
@simplyklean
2 ай бұрын
Could you let me know where you got those steel lines and fittings going from wastegate to controller?
@simonkim0321
9 ай бұрын
Clean!
@bobbydelamar606
Жыл бұрын
I lost track. What was the total? I'd love to turbo my K24A2 CRX.
@farrinmccahill6920
Ай бұрын
I want that in my mine and go bye bye and just go slow to, our you have to keep it wond up, no time for turb lag ,its just wanted to go in the launch mode!?
@gregorykirchner6327
11 ай бұрын
What fuel regulator is that
@bluegizmo1983
5 ай бұрын
Just a note for people doing builds in the future: oversized injectors (i.e. buying larger injector than you need for your planned build just so you can go bigger in the future like he did in this video) is a BAD idea! Any tuner worth their salt should know that. Going with bigger injectors that you need makes tuning down low, especially idle, very inaccurate. This is because the larger your injectors are (when you can't use all the injector yet because their oversized for your current build) you have to turn the injector duty cycle down so low at idle and low speed that they are either barely opening or open too long, as no injector likes to be ran and super low or super high duty cycle, i.e. not above 90% duty cycle because they can stick open, and not below 2% to 5% duty cycle because they may never open, and if they are too big for your build you will get real close to the minimum never opening duty cycle so you'll be forced to run too rich down low and idle. Stick with injectors that are JUST big enough for your planned build plus maybe 5% to 10% overhead, and upgrade the injectors in the future if you change your build or boost levels.
@davidmorris-fz6ts
2 ай бұрын
if you're getting tuned on k pro yes, not if you're getting tuned on a haltech ecu or anything that runs ve maps
@Hello_its_me_mario
Жыл бұрын
Umm. That drain tho. How is it holding up?
@lavrentievv
Жыл бұрын
None of those parts are budget. Can easily get a full set up for 3-4000$
@rxtoy23
Жыл бұрын
Where??
@edgardogaray7426
5 ай бұрын
Absolutely agree this is in no way a budget turbo kit supper clean but not budget
@apollonitro4802
3 ай бұрын
Budgets are relative bro
@user-hh4hc2lt6e
Жыл бұрын
What’s that sensor on the side of the intake manifold, by the serpentine belt
@jgc0064
Жыл бұрын
MAP sensor
@markanthony5011
Жыл бұрын
Are you still using the stock K24A pistons and rods in your turbocharged engine?
@smokeandmirrors-pk6ic
4 ай бұрын
He didn’t mention a rebuild so, yes. Not sure why he dropped 2k on turbo but left stock intervals smh
@awd_pirate1946
Жыл бұрын
Its clean but why not ceracoat all the exhaust hot side? Or at least wrap/turbo blanket?
@oemworx4147
Жыл бұрын
Thanks. Stay tuned for next update video.
@Dfwrich
Жыл бұрын
what size cold side piping? 2.5"?
@oemworx4147
Жыл бұрын
Yes.
@adamloveshondas3122
Ай бұрын
But did you put rods and pistons …. turbo is sucking all that hot engine bay heat 🤦🏼 but overall looks nice just don’t understand why people build a time bomb 🧐
@RoadsterAlex
Жыл бұрын
6000-10000 a budget ? Dude you can do this for 2k 😆😆😆
@rxtoy23
Жыл бұрын
Where??
@RoadsterAlex
Жыл бұрын
@@rxtoy23 by taking different products :) pulsar turbo etc
@rxtoy23
Жыл бұрын
Noo, I’m asking who did your build ? What shop ?
@RoadsterAlex
Жыл бұрын
@@rxtoy23 shop? Diy obviously who gets their car build by a shop
@akuroakum8955
5 ай бұрын
Yes but will it look this clean?
@LTR450black
3 ай бұрын
How is anything on this engine build a budget Garrett turbo turbo smart wastegate turbo smart blow valve fuel system I’m in the list goes on wire harness I don’t think it’s all 100% a budget build
@Cloudyy64
6 ай бұрын
😂
@boosted__demon6852
10 ай бұрын
I haven't finished the video, I had to stop when you mentioned the price of the turbo. This is not a budget build, this is way overpriced.
@k9deine351
Жыл бұрын
You call that a budget
@JavaughnDawkins1997
Ай бұрын
He said it multiple times, when he said budget build it’s whatever your budget is, everyone budget is different. He literally said it at the beginning.
@k9deine351
Жыл бұрын
You could've got a used mustang for that much
@garyphloyngam7148
Жыл бұрын
Bro nice setup man I salute 🫡 i cant wait to get my eg
Пікірлер: 51