Been running PPS for a couple years now. Biggest challenge was finding the correct adapter. This system is awesome Great for quick cleaning of the gun also. Switch to thinner container and flush ...
@ben_r_
4 жыл бұрын
Now do a new video showing the 3M PPS 2.0 system with Fuji spray guns!
@FujiSpray
3 жыл бұрын
kzitem.info/news/bejne/z2uswJ-GoXmLm2k
@tigertigerpantherfox3714
4 жыл бұрын
Ive been using PPS on my Fuji Gravity gun for 3 years. Still need to clean it out but this system is much better. I just wish Fuji would supply the correct parts when i was looking to convert my gun back then. USA imports to the United Kingdom are expensive!!!
@1paidoseunenem
2 жыл бұрын
3M™ PPS™ Adapter, 16054, Type 18 this is the the right part number for bottom feed cup and you can find it on Ebay for about $30.
@FujiSpray
2 жыл бұрын
Yes that is the correct adapter for the bottom feed spray gun.
@fuzzyrat123
Жыл бұрын
Now explain what happens when the u tube falls out from the nipple that is connected to the gun and won't hold any longer. Just bought mine and within 10 minutes the metal tube fell out and won't stay connected.
@FujiSpray
Жыл бұрын
Sorry to hear this happened, please contact Fuji Spray directly via email. We look forward to assisting you further. - Fuji Spray Team -
@ApexWoodworks
4 жыл бұрын
Great overview of this system, Jim! Thanks for sharing your expertise.
@darrelmorrison5972
3 жыл бұрын
I would to see a pic of the m-gravity gun with the h/o cup installed. What happens to the bottom tube?
@FujiSpray
3 жыл бұрын
After the 3M PPS setup is installed on a M-Model Gravity Spray Gun, it will then look like a Bottom Feed configuration. - Fuji Spray Team -
@zonial
9 ай бұрын
Why is it that I can't find the # 18 adapter anywhere.....?
@FujiSpray
8 ай бұрын
Please contact Fuji Spray directly. You can reach out via our "contact us" page. - Fuji Spray Team
@texascrossbowdude636
Жыл бұрын
Where are the gun holders shown available?
@FujiSpray
Жыл бұрын
The gun holders in the video are custom-built holders and unfortunately unavailable. Fuji Spray offers Spray Gun Holders of other types, like the 5330 gun holder stand and the 5375 magnetic gun holder. - Fuji Spray Team -
@dollface2106
2 жыл бұрын
So I have the M model bottom feed which I converted it into a gravity feed so basically what I am confused on is your instructions for that type of situation will I still be able to use my gravity feed conversion set up with the 3M cups or would I have to convert back to the original bottom feed set up
@FujiSpray
2 жыл бұрын
In order to use the 3M PPS setup on the Fuji M-Model spray gun, it will have be converted back to bottom feed configuration. The 3M PPS S18 Adapter will be the size for it. - Fuji Spray Team -
@troybrake5686
Ай бұрын
Will the cup side of the conversion tube not connect to an adapter? ( the 3M #18) I'm under the impression a s21 adapter (14mmx1.0mm) will thread to the u tube cup side,?what is the tread on the u tube( both sides) ? I'm about to order the conversion tube, any help would be awesome! 😎
@damann3303
4 жыл бұрын
Very concise, but this is for the old version. PPS 2.0 is now the standard and has some differences. Perhaps a new video is in order ?
@FujiSpray
4 жыл бұрын
We appreciate your feedback, that is a great point you bring up! We've been excited for the PPS 2.0 H/O Cups and will update shortly. If you have any questions regarding the differences between the two series, feel free to give us a call!
@matouellet4326
7 ай бұрын
You skipped over the M model gravity feed?
@FujiSpray
7 ай бұрын
The M-Model gravity feed will be exactly like the bottom feed. After installing the #18 adapter, the gravity M-Model spray gun will then become a bottom feed configuration, there's just no way around that. Hope this helps!! - Fuji Spray Team -
@markymark2599
2 жыл бұрын
So you don't use the air line with the check valve that goes to the cup and it just stays off?
@FujiSpray
2 жыл бұрын
At the 6:47 mark you will notice that there is a pressure tube installed. This pressure tube comes included with all 3M PPS H/O Series. The existing Fuji Spray pressure tubes hould be removed to install the on provided by 3M. -Fuji Spray Team -
@jamesmyers2087
Жыл бұрын
Cannot find that number 18 adapter anywhere. Do you have a link?
@FujiSpray
Жыл бұрын
3M has rolled out the 2.0 PPS series. You would want to look for part # 26054 which is the S18 Adapter. Alternatively, please reach out to Fuji Spray directly to point you to a distributor who offers this item. - Fuji Spray Team -
@jamesmyers2087
Жыл бұрын
@@FujiSpray i did find it. Problem was the first number changed. Thank you.
@cryptoneon
3 жыл бұрын
so what cup system for the PPS 2.0 now 3M have put a spanner in the works and stopped doing the 1.0. I have purchased theseries 2.0 type 24 adapter for my G-Xpc, but not even 3M help desk have a clue what I'm after.
@FujiSpray
3 жыл бұрын
If you are wanting to connect the 3M PPS 2.0 to a GXPC spray gun, you will need the following: #S24 Adapter - part # 26110 H/O (High Output) Midi Cup - 13.5oz - part # 26121 Then you can purchase the lids and liners for the Midi Cup separately NOTE: Only the Midi Cup setup will fit the GXPC spray gun. -- Fuji Spray Team --
@spkendrick
3 жыл бұрын
I still need the #18 adapter for the 1.0 system and the 2.0 pps system?
@FujiSpray
3 жыл бұрын
3M has kept the same sizing numbers as to not confuse, but the physical items are completely different. for 2.0 series, the part # is MMM26054 (called the S18). For the 1.0 series, the part number is MMM16054. You would want to go with the 2.0 series as the 1.0 is being discontinued and accessories will become harder and harder to find. - Fuji Spray Team-
@JuanMartinez-qp6yg
3 жыл бұрын
Great video Jim ...question?Where can I purchase the kit? Also the adapter, i own Fuji mini mite with the gravity gun...thanks
@FujiSpray
3 жыл бұрын
Thank you for your comment. Please contact Fuji Spray directly to help you find a distributor near you. 1-800-650-0930 or support@fujispray.com. - Fuji Spray Team -
@jameswilliams5982
3 жыл бұрын
Why can’t you get the 3m connector in the uk????
@FujiSpray
3 жыл бұрын
Please contact Fuji Spray directly and we'll sort you out as quickly as possible, support@fujispray.com - Fuji Spray Team
@AverageOverlander
4 жыл бұрын
I thought the HVLP guns weren't compatible with the 3M PPS system H/O pressurized cup? I have the GXPC with the #24 adapter that I bought a few months ago and the 3M PPS cups wouldn't work with it. When I emailed you earlier this year you replied with this: "HVLP systems require the cup to be pressurized, therefore unless you were able to source a 2.0 version with a Type H/O pressurized cup, the guns are not compatible. As mentioned, 3M is in the process of releasing these 2.0 H/O pressurized cups, however to our knowledge they have not hit the market yet."
@FujiSpray
4 жыл бұрын
Yes - they very much are. With the #24 adapter for your GXPC gun, plus the H/O (High Output) version of the 3M PPS - it is definitely doable. The 2.0 H/O series is now available in the USA market, whereas it is slowly staring to appear in Canada. Please feel free to reach out to us at info@fujispray.com if you require further assistance - Fuji Spray Team
@AverageOverlander
4 жыл бұрын
@@FujiSpray something to add, people need to buy the S24 adapter. The non-S #24 adapter is for PPS 1.0, not compatible with 2.0.
@harvey8695
Жыл бұрын
Jim, is the check valve necessary when using the PPS?
@FujiSpray
Жыл бұрын
The check valve is not necessary when using the 3M PPS setup. Reason for this, the 3M PPS system is self-contained and there's little to no risk of any material entering the pressure tube and ending up in the air passages of the spray gun. One of the main functions of the check valve is to prevent material backflow into the spray gun and causing damage. - Fuji Spray Team -
@JonathanStrong
Жыл бұрын
Hey Jim - I just placed the order for my first sprayer - a Hobby Pro 2 - and wanted to use the 3M PPS with it if possible. I don't see any suggestion that 3M PPS 2 is compatible with the Semi Pro 2 or Hobby Pro 2. As I understand it, these are "M" series HVLP, and the bottom feed should work with PPS 1.0 (legacy) #18 adapter and the 3/M PPS H/O cups. Is that correct? Also - using this combo, will I still be able to spray at any angle, as when using the PPS 2.0 with the top feed Fuji sprayers? (thx in advance)
@FujiSpray
Жыл бұрын
The 3M PPS cup system is indeed compatible with all Fuji Spray spray guns. The PPS adapter for the M-Model spray gun is the #S18 for the 2.0. For the 3M PPS 1.0, you would want to use the #18. With the 3M PPS setup you will be able to spray at any angle. - Fuji Spray Team -
@JosiahGarber
2 жыл бұрын
Does the hose from the gun to the cup come with the PPS system or the Fuji System? Does it not need an inline filter? And where do you buy replacement hoses?
@FujiSpray
2 жыл бұрын
3M includes a pressure tube for H/O (High Output) cup setup. It will be long enough to cut into two and keep the extra aside. You will not need to replace the pressure tube; there's no risk of it getting dirty with material in it. If you ever do need to ever replace, your local hardware store will likely have. The pressure tube does not require a check valve. - Fuji Spray Team -
@JosiahGarber
2 жыл бұрын
@@FujiSpray Thank you that is helpful.
@carlevanko2060
2 жыл бұрын
What gun would you recommend for refinishing cabinets along with the 2.0 PPS system?
@FujiSpray
2 жыл бұрын
It really boils down to personal preference on which spray gun to go with. For this application, we would recommend going with the Gravity Feed T-75G spray gun. Coupled with the 2.0 3M PPS Series, a gravity feed spray gun will use up a smaller footprint if compared to the Bottom Feed spray gun installed with the 2.0 3M PPS Series. This will be very advantageous when spraying inside the boxes of cabinet spaces, specially for tighter areas. - Fuji Spray Team -
@Therealphantomzero
3 жыл бұрын
Man this is annoying, I went to order the 3M 2.0 for the t70 and it seems like it's supported since it's the new system I don't want to go with an older system but I have the t70 the one that has the big cup underneath the siphon I ordered the adapter there's 3M tells me it's going to be the s2c but it's not the threads are too thick while the gun threads are much thinner the right size diameter not the correct threads I cannot find a 2.0 system adapter for the t70 what is it @fuji
@FujiSpray
3 жыл бұрын
The 3M PPS 2.0 adapter size for your T-70 Bottom Feed Spray gun is the S18 adapter, part # MMM26054. - Fuji Spray Team -
@Therealphantomzero
3 жыл бұрын
@@FujiSpray thank you ordered, please bring the turbine spray guns back that would be great lol.
@adriandeb2710
3 жыл бұрын
Do the normal liners fit in the hard cup, or do you need special liners
@FujiSpray
3 жыл бұрын
The 3M PPS Cup Liners will only fit the 3M PPS Cup System. Fuji Spray offers liners that can be inserted in a standard bottom feed cup, but the purpose is reduce cleaning time only and will not to allow you to spray at any angle like the 3M PPS Cup System does. If you have any more questions, please reach out to our Customer Care at support@fujispray.com or call 1-800-650-0930. - Fuji Spray Team -
@danjohnson6292
3 жыл бұрын
For a weekend warrior car resto guy, what turbine system would be recommended for epoxy primers, base and clear? I was thinking the Q4 or Q5. Thoughts?
@FujiSpray
3 жыл бұрын
You're definitely on the right track. Q4, Q5, Mini-Mite 4 or Mini-Mite 5. The Mini-Mite models are a little bit louder but portable, and the "Q" models are the quietest on the market - Fuji Spray Team -
@drewbush6535
4 жыл бұрын
So is my gun gravity fed if cup is above gun but enters in the bottom of gun?
@FujiSpray
4 жыл бұрын
If your gravity gun has its cup installed from the front-bottom of your spray gun, you will need the 3MPPS #18 adapter. Please note that after you install the #18, your spray gun will become a bottom feed spray gun. - Fuji Spray Team -
@moderntouchfurniture
3 жыл бұрын
I have a T70 bottom feed system, but you never showed how to attach the bottom feed cup? (1:57) Is it the same cup that goes on top, 22 for 13 oz size, just with a #18 adapter instead of #2 adapter? Also on the gravity feed, do you recommend the H/O system over the regular gravity only system. I understand you can spray upside down because you have the air pushing the liquid, but you can not do this without the H/O cup system?
@FujiSpray
3 жыл бұрын
For the first part of the question, yes, the same principle (using the #18 adapter) will apply to your Fuji T-70 spray gun. For the second part, when it comes to all HVLP turbine driven equipment, you will always need to use the H/O cup setup. Unlike conventional spray guns (the ones that connect to compressor setup), the HVLP turbine spray guns' ventury effect is not effectively strong enough to draw in the material from the cup without the assistance of a pressurized cup. This is because the HVLP turbine spray guns already operate a very low pressures. Hope this helps! - Fuji Spray Team-
@brwildcats
Жыл бұрын
Hello, I have the gxpc gun. Which high output cup should purchase to use the air tube that pushed liner down when using?
@FujiSpray
Жыл бұрын
You would want to get the Midi Cup, part # 26121. - Fuji Spray Team -
@brwildcats
Жыл бұрын
@@FujiSpray thanks, also need info on correct tips for my gxpc gun? I've ordered the 2.0 and the 1.5 tip but they didn't fit my gxpc. Any help on correct tips would be great. Thanks ahead of time.
@FujiSpray
Жыл бұрын
@@brwildcats Hopefully you are able to send them back. The part numbers for the GXPC air cap sets have the # 8050 prefix. The air cap set part numbers are 8050-2 = 0.7mm, 8050-3 = 1.0mm, 8050-4 = 1.4mm (this one comes installed din the spray gun), 8050-5 = 1.8mm and 8050-6 = 2.2mm. 1.5 and 2.0 are not offered for the GXPC spray gun. Hope this helps! - Fuji Spray Team -
@war3405
4 жыл бұрын
Hi to conect Gxpc gun to cHowompresor and using thinner hose?
@FujiSpray
4 жыл бұрын
There are special adapters out there to achieve this, but very rare and difficult to find. Even though it is possible to connect to compressor, we advise to please not exceed any more than 20 psi. Some of the components of the GXPC are not designed to withstand high pressures, only pressure coming from a turbine unit which is up to 10psi. If you require any further assistance, please feel free to reach out to us at info@fujispray.com. - Fuji Spray Team
@war3405
4 жыл бұрын
@@FujiSpray Hi Can I conect pressure pot with compresor and using Gxpc gun? Thank you
@sgondor2768
2 жыл бұрын
Do you still need the check valve with the 3m pps pressure pot?
@FujiSpray
2 жыл бұрын
Yes, it is necessary to have the pressure tube attached to pressurize the cup. 3M calls it the "H/O Cup" (High Output). This is true only with HVLP Turbine driven spray guns. For spray guns that operate with an air compressor; the pressure tube is not necessary and that would be 3M's standard cup. -Fuji Spray Team -
@sgondor2768
2 жыл бұрын
@@FujiSpray I know the pressure tube is required but I'm asking if it's required to have the check valve that came attached to the original pressure tube that came with the gun between the gun and the pot.
@FujiSpray
2 жыл бұрын
@@sgondor2768 Thank you for the clarification... The check valve is not necessary for the cup. 3M includes a piece of tubing for the setup and does not have the check valve either.
@sgondor2768
2 жыл бұрын
@@FujiSpray thanks for the fast responses! One last question. Can I cut the tube in half that came with the 3m cup? It's very long and flops around a lot when mounted into position.
@FujiSpray
2 жыл бұрын
@@sgondor2768 Yes, you can cut it as long as you need to.
@DonnieKluck
2 жыл бұрын
How much can you actually paint with the 3oz or 6oz cups? I am new to wood working and spray guns, it just seems like you would have to stop a lot to change it out or refill it. But again I dont know what I dont know and maybe a little goes a long way. Thanks for bearing with me and my noobness.
@FujiSpray
2 жыл бұрын
No to worry, we're here to help all levels of spray finishing; whether getting the right information to purchase the spray system for your needs, to the professional spray finisher looking to improve their craft. The smaller cup setups are for small spray projects like jewelry boxes, doing details or touchups. The larger cup allows for larger spray projects like furniture pieces, cabinetry, etc. Hope this helps! - Fuji Spray Team -
@DonnieKluck
2 жыл бұрын
@@FujiSpray Cool thanks I appreciate it. Makes sense. So like when and why would you want to use like those huge cups like the 22oz or 28oz ones? Could you use the Q4 Platinum to spray the exterior of your house (I assume so) but would you need anything else like a pressure pot?
@FujiSpray
2 жыл бұрын
@@DonnieKluck That would boil down to a matter of preference, but this question may be best be answered by 3M themselves. - Fuji Spray Team -
@DonnieKluck
2 жыл бұрын
@@FujiSpray Thanks appreciate it. One other question in paint sprayers in general. When you use one does paint go every where or hang in the air? I did not know if I would have paint land on everything else if it was not a sealed environment. Like would I have to worry about it if I was in the garage and just had the side and floor covered, or would it drift up and over/around and land on other things? Only asking is cause I spray painted our fireplace and had it taped off and sealed with plastic and there was still paint particles that ended up 20' away from the enclosed area.
@FujiSpray
2 жыл бұрын
@@DonnieKluck When spraying with turbine HVLP technology, you can expect very little overspray; this is one of the key benefits of turbine HVLP spraying. There is still overspray nonetheless, and although very little of it, it will look like a light film of dust within the vicinity, but not stuck to the surface; just dried dust that can be easily wiped off.. It is always very important that proper ventilation be in in place when spraying in indoor settings. Some sort of extraction fan will be super useful. - Fuji Spray Team -
Пікірлер: 79