I have seen a lot of newbies use the term PTO (Power Take Off) when they mean to say Three Point Hitch. They just don't know any better. He could have said adjust the right side link turnbuckle adjuster. By the way for those who do not know an Imatch is more fun when paired up with a TopNTilt setup. Where you have hydraulic cylinders in place of your top link and your right side link turnbuckle. Then you can truly sit on the seat and make those adjustments with your hydraulic control valves to get hooked up and adjust for level on the fly all from your seat :) James
@truckerray7533
7 жыл бұрын
James B. That what I couldn't figure out is how in the world could he be using the "PTO" to adjust the side links? Like ya said. . . . a "newbie who don't know any better"!
@artschulte1897
2 ай бұрын
Does the adjustment bar on the right also level out , raise or lower the quick hitch to put it on a slant for grading ?
@divertim1
10 жыл бұрын
I noticed that you said in your video that you use the PTO to adjust the Imatch.. How does the power take off adjust the lower link arm?
@scottchadbourne4759
4 жыл бұрын
I really like the iMatch, however, hooking up to these new safety styled PTO shaft couplers can be a real pain if dealer didn't trim the implement's PTO shaft to the right length and tractor isn't level.
@nrfa6229
7 жыл бұрын
Great simple, to the point, short but also very descriptive all in one video. Thank you! Keep these coming. Nicely done. I've got a 2016, 1025r TLB, with a handful of attachments for it. I was wondering if you have a video like this on how to setup from the very beginning? I've never used mine yet, and would like too. Thanks so much and thanks again for straight to the point descriptive video. You're definitely above the rest by doing that. Beats someone going on and on for 20 mins, for what you accomplished in 1:32. I thumbed up and subscribed. 👍
@Muttonpower
7 жыл бұрын
Thanks for the feedback. The initial install is the same as any std 3-pt attachment. Hook up to the draft arms first and then the top link.
@pappy1432
5 жыл бұрын
I bought a new JD 2038 with imatch and rototiller , loader of course. guess what no aftermarket implements fit the imatch. and JD is twice as much as tractor supply. I use just the 3 point hitch , cheaper.
@mikeolechnowicz8112
5 жыл бұрын
I also found that out,they don't tell you that at the dealership,all old implement don't work,need to be modified,but what they said was, once you do it then your done,go figure.
@jshan8205
3 жыл бұрын
For the life of me i can't get my pto to adjust my quick hitch. I have used the pto lever mid pto lever. Nothing happens but the pto spins. Im at a loss with this pto deal. 🤣🤣
@brikkijim
3 жыл бұрын
How do you adjust the width of couplers?
@jonathanerickson2007
2 жыл бұрын
Good job
@semco72057
8 жыл бұрын
The quick hitch I got from the JD dealer is more like the one Harbor Freight sells, but better in quality. I wish they had a large bolt on top to adjust the height of the top hitch with a wrench or ratchet.
@tenrodfarm3744
9 жыл бұрын
I have a Deere 5410, Cat 1/2. Does Deere make different models of this for each category or would I just get one for a Cat 1 and then use bushings for Cat 2 implements?
Пікірлер: 18