I got my kit the other day and there is NO information on what to use as a starting point for the height. A member on the Fiesta ST forum suggested 2.5" of exposed threads while on the car. I went with 2" of exposed threads which made for a 1.5" drop. Doesn't look like much but what a difference it makes compared to the stock setup. More secure cornering with less body lean, I am very happy so far!!!
@ssarkees
9 ай бұрын
Thanks! I was wondering how I would raise or lower after they were in.
@racelandsuspension
9 ай бұрын
It depends on the vehicle. Give us a call and we can talk you through that. Our number to call is 801.365.1440.
@tatocastillo4539
2 жыл бұрын
I just purchased a coil over from you guys I’m exited about it and my question is on the pre load you said just tight the spring and that’s it or I need to pre load any 4 to 5 mm pre load ?
@racelandsuspension
2 жыл бұрын
Yeah, 5mm would be the max preload that you'd want to set them to.
@tatocastillo4539
2 жыл бұрын
@@racelandsuspension thanks David I’ll send pictures of the install and final results 👌🏻🫵🏻🙏🏻
@thefisch1332
Жыл бұрын
@@racelandsuspension so we can adjust them to less then 5mm? When I did mine on my 06 Forester xt I watched the original video that said to set to 5mm. Way too stuff for me. I'll be adjusting them this weekend if we can do less. Thanks!
@racelandsuspension
Жыл бұрын
The pre-load really won't affect the ride.
@jerenzbronilla1938
2 жыл бұрын
Do you need adjustment of wheel and camber when adjusting the height of coilover?
@racelandsuspension
2 жыл бұрын
Yes. As you lower the car, the camber will become more negative and vice versa.
@edvinbaron2095
11 ай бұрын
Thanks dude!! But I have a question, how does the adjustment of the spring tension affects the ride rollovers? I'm using a high-low fully threaded coilovers, my ride rolls terribly like I'm using standard factory springs and absorbers, what is the perfect spring height to make sure the rebound is slower and make the ride stiff ?
@racelandsuspension
11 ай бұрын
Give us a call and we'll run through some troubleshooting with you. Our number to call is 801.365.1440.
@kakkahaisee-dk1gm
Жыл бұрын
So whats the difference between partially and fully threaded when adjusting spring seat? Does preload on fully threaded affect ride height like it does on the partially threaded?
@racelandsuspension
Жыл бұрын
With a partially threaded kit, the preload is what determines the ride height, where a fully threaded kit isn't. The ride largely won't be significantly different as we tune the spring and damping rates per model and drop range.
@jpcutzz5455
2 жыл бұрын
On the Infiniti g35 set of primo I have it comes with 3, is that correct ? I would love an installation video on them
@racelandsuspension
2 жыл бұрын
Here is a link to our install video- kzitem.info/news/bejne/omaPyZqOhpOLiGU
@isaiahe174
2 жыл бұрын
After installing these, I keep on hearing a thudding sound every now and then is there something else that should be tightened or should I call to replace the 2 driver side coilovers?
@racelandsuspension
2 жыл бұрын
Give us a call and we'll run through some trouble shooting with you. Our number to call is 801.365.1440.
@Trashmane_
2 жыл бұрын
Just wanna make sure I heard that right. If you compress the spring by taking the collar up you are raising the ride height?
@racelandsuspension
2 жыл бұрын
For a partially threaded kit, yes.
@kevinjay8051
Жыл бұрын
which of these kits/setups would apply to the 2013-2019 BRZ coilovers?
@racelandsuspension
Жыл бұрын
Our BRZ kit is a fully threaded kit.
@nathanhatch1971
6 ай бұрын
On the fully threaded ones, how do I know when I’ve reached max height? Is there a stopper or will the whole thing just fall out of the bottom mount?
@racelandsuspension
6 ай бұрын
It depends on which kit you have. For most, there is a peep hole on the side of the lower mount. As long as there is thread showing in the peep hole, you're safe.
@johnnycooley6761
Жыл бұрын
I'm confused by this. The Coilovers I purchased from you guys are like the ones to the guys right and look nothing like those. Mine have 2 separate springs on front struts. Taller spring on top with a lower mount then a smaller spring below that with 2 adjustment nuts on the bottom of those springs. There were no instructions in the box just a sticker and key chain. I've either thrown away invoice or misplaced it and need to know if I am adjusting them right or wrong. Thanks
@racelandsuspension
Жыл бұрын
Give us a call when you have a moment and we'll clear that up for you. Our number to call is 801.365.1440.
@joshmeacham3326
2 жыл бұрын
Can you buy the wrenches from you guys? I bought a Subaru with these, but the owner only had one wrench
@racelandsuspension
2 жыл бұрын
For sure. Give us a call to order. Our number to call is 801.365.1440.
@calebdunn8703
2 жыл бұрын
So when your raising it to its max, it it okay if the lip above the actual collar is raised over the mount. This is really hard to explain lol sorry.
@racelandsuspension
2 жыл бұрын
No worries. Which vehicle do you have?
@Henry-jr5bv
Жыл бұрын
It’s the same for the rear coils on an Acura RSX ?
@racelandsuspension
Жыл бұрын
Yes. To raise the car, turn the collars up the shock etc.
@WheelerDealer1561
6 ай бұрын
Which of these set ups would apply for a 2014 Scion tC?
@racelandsuspension
6 ай бұрын
Our tC coilovers are partially threaded coilovers.
@diaz_reyes5558
4 ай бұрын
How about the preload on the rear coils ?
@racelandsuspension
4 ай бұрын
For which vehicle?
@fordracing5oh
7 ай бұрын
How to adjust the classic for 99-04 mustang
@racelandsuspension
7 ай бұрын
Our Mustang coilovers are known as "partially threaded" coilovers, so the process will be the same.
@angelocaluya5081
Жыл бұрын
I’m having trouble removing the coil
@racelandsuspension
Жыл бұрын
Feel free to give us a call and we'll run through some troubleshooting with you. Our number to call is 801.365.1440.
@LazarosOdwar
4 ай бұрын
I lost the tool where can I buy another
@racelandsuspension
4 ай бұрын
Give us a call and we can get an order through for you. Our number is 801.365.1440.
@kwvq8762
2 жыл бұрын
Why don’t y’all sell the top mounts for the 06 maxima kits
@racelandsuspension
2 жыл бұрын
We are expanding our upper mount line-up. We'll keep you posted if we decide to do the kit.
@duxkuna9685
Жыл бұрын
i have a set of coils for the subaru forester 03-08, is there any way to make the springs more stiff at all? particularly the rear?
@racelandsuspension
Жыл бұрын
Unfortunately, there isn't a way to stiffen up the springs.
@duxkuna9685
Жыл бұрын
@@racelandsuspension thank you very much
@FastLab_Garage
Жыл бұрын
my car is extremely stiff in the rear how to make it softer i have fully threeaded coils
@racelandsuspension
Жыл бұрын
Which coilovers are you running?
@FastLab_Garage
Жыл бұрын
@@racelandsuspension ta technix fully threaded in front i learnend how to make them softer but in the rear they are hard stiff need help please
Пікірлер: 50