In this short episode I show how I put my pipes in chased thermolite brick walls, clipped and protected. Moving a water main and replacing the stop tap with also fitting 2 outside taps for hot and cold water!
Really nice workmanship like the way you did a set on the right horizontal piece instead of running it at an angle
@no-ic3rg
Жыл бұрын
You work to a high standard look forward to your videos.
@mmplumber
Жыл бұрын
Really appreciate it pal
@owsi2297
Жыл бұрын
Great work mate👏 keep them coming 👍
@TheMark1840
6 ай бұрын
I love your videos and your explanations. Im getting a lot from them. Thanks.
@bwan47
Жыл бұрын
alright mate i remember working with you in a kitchen late last year 👍
@mmplumber
Жыл бұрын
Sparky or chippy? 😂
@bwan47
Жыл бұрын
Sparky . Working on a kitchen
@mmplumber
Жыл бұрын
@@bwan47 I remember buddy hope your all okay and using the packout still 🤣 I still need to buy mine!
@AminAz-wb5ph
2 ай бұрын
Iwant see you how you put the boiler mate😊
@hassyg4083
Жыл бұрын
how to be a plumber or learn any trade go to job centre and college yall
@FlyingAndy
Жыл бұрын
quality vid mate well done
@MrMedicalUK
21 күн бұрын
Ouch black MPDE
@Mike_5
Жыл бұрын
Pipework chases are so much fun as they always annoy Kitchen Fitters and Electricians!
@mmplumber
Жыл бұрын
Always good to spice up there days eh 🤣
@Razz60
Жыл бұрын
Great video just wanted to ask when you 1st fixs for standard rads whats the distance you leave on each side for valves to fit? For example if you had 1000mm length rad what distance wud you leave on each side for valves to fit? Thanks
@mmplumber
Жыл бұрын
1080 I would allow for and if pipes coming out the floor drill a 20mm hole so you have play or even 25 if carpet above
@mmplumber
Жыл бұрын
40mm either side
@mmplumber
Жыл бұрын
Sometimes if your using loctite or liquid ptfe you need to go in as the they finished tighter so 75mm added
@Razz60
Жыл бұрын
@@mmplumber thank you very much
@FlyingAndy
Жыл бұрын
questions: 1/ how high do you set your 1st fix above ffl? is it always the same? are rad pipes always the same distance apart or do different valves mean you have to measure each time, ie if you have a 500mm towel rad, you always set your pipework at 550mm centres for example?
@mmplumber
Жыл бұрын
So above here was plastic but it’s all clipped and in straight lines so no tension on anything . For rads you add 40mm on each end for valves. Here on the towel rails you come in 22.5 from each side for valves going back into the wall. So if it’s 500 wide your 455 pipe centres
@johnmcnamara4846
7 ай бұрын
Quality video.
@pallsmortion4750
Жыл бұрын
What's the point in putting points to improve on when you argue you were right in the first place?
@mmplumber
Жыл бұрын
Improve on the video making mate, I want to know your feed back and how I can make the videos better for you to watch. There’s always different ways to do plumbing. Aslong as we get the best result in the end that’s all that matters.
@TheDickPuller
Жыл бұрын
For the Towel Rail tails, I’d not clip tight at the tails, it gives you some movement when you’re fitting the Valves. That’s Black Alkathene Class C or D.
@mmplumber
Жыл бұрын
That’s why they are in a chase and only strap banded over the top and not around the pipe. I technically got wiggle room in the that chase 👍👌
@mmplumber
Жыл бұрын
Cheers mate for the info!
@schmuuth_dot_com3202
Жыл бұрын
Nice work - think the format is good - you could equally mix a bit of 'live' commentary and voiceover for variety but I enjoy your content - I typically watch pb, mjtiff, nathan and tom plumb but look out your videos when they appear too
@mmplumber
Жыл бұрын
I’m going to start focusing more now on KZitem so expect more regular vids on the week I’ve had!
Пікірлер: 30