A masterclass Derek, thank you for generously sharing your knowledge with us; great detailed videos, with clear, helpful close ups. You've saved me hours of frustration, top man 🙂👍
@tomkatgastraining
29 күн бұрын
@@Marktb363 thank you 🙏
@saleh8944
3 жыл бұрын
To the thumbs down folk who obviously didn't understand or fully appreciate the best pipe bending videos out there: I would suggest you pay someone to do it for you as Derek is far and away the best instructor on this subject :)
@mikebarron4929
4 жыл бұрын
I've been plumbing 37 years and I've not long found your channel and can say honestly if all tutors were as straight to the point and clear in there instructions as yourself then the training industry would be much improved your vids are spot on with little faff and lots of good knowledge
@tomkatgastraining
4 жыл бұрын
Thanks for your comment and watching cheers
@phasedout6769
4 жыл бұрын
Honestly the most helpful video on bending I've seen. Hats off. Time to mark my bender 👍
@hdhanji8006
4 жыл бұрын
Great tips thrown in Derek... measured properly with no unnecessary pipe wastage 👍
@mohammednadeem7274
3 жыл бұрын
Another well presented video with very valuable tips to help with the pipe bending, I love the drawing with the angles, the solder was a well cool tip to get the bends and angles correct. An excellent video once again derek.
@johnswilley6764
2 жыл бұрын
Thank you Sir! I'm going through your videos, just got to #2, getting ready to make a Cu pipe dryer/receiver setup for my compressor. You have produced an excellent stock of info. From Orlando, Florida, U.S.A. thanks again, and best wishes!
@mj0n4id36
3 жыл бұрын
Truly amazing. Great tips given by a great teacher. The making use of a template and solder is genius. Marking out the centre of the pipe was a great tip too. I’m going to create a template, laminate it and keep it with my pipe bender. Thanks Derek 👍🏻 Asian Jon. Training.
@Agopper
4 жыл бұрын
Great learning video as usual and thanks for for sharing your knowledge to newcomers, all your video are very educational for new entries in the trade cheers derek
@MarcusT86
3 жыл бұрын
Thanks for taking the time to make these. Great stuff mate!
@joebaikaikamara7509
10 ай бұрын
Great tutorial lesson
@AJ-cw9rb
4 жыл бұрын
As always Derek, great Video, keep it up mate 👍
@davyogi9796
3 жыл бұрын
Thanks Derek, at least you have shown that sometime we can over bend the pipe, marking the bender and another great tip, a bit different to when I was tault with 2 metal folding rules.
@willlomas2725
2 жыл бұрын
Very informative Derek .....Thanks.
@rivkiroyde4362
4 жыл бұрын
Thanks Derek great video 👍👍👍
@TheRumpusView
2 жыл бұрын
Thanks very much for this. It is just what I need, except I need to do a 60mm offset on 22mm pipe. I need to work out what the minimum offset is, I hope that a 30 degree bend is possible. Good camera work here. Well done.
@monikanader9454
3 жыл бұрын
Another great video👍
@TheDickPuller
4 жыл бұрын
Very informative as always Del. Know what I was impressed by most - that fucking Silverline bending machine, it looks the Dog’s Bollox!! I guess for the course cowboys & career change chancers you can only buy cheap tools. Of course for speed on-site, you don’t have time to draw lines. For a parallel line stick the pipe against the Skirting & measure/mark from that. Another wee tip; use a bit of core solder to get the complete offset size, centre to centre, then use that on yer Bender.
@fredjennings9268
4 жыл бұрын
Informative... thanks for giving you time👍
@ashkanrajabzadeh9632
4 жыл бұрын
That’s perfect boss
@markroberts6864
3 жыл бұрын
Cheers
@rotarurazvan8792
3 жыл бұрын
You are great, clever...
@koliakolian810
3 жыл бұрын
Good
@1Monaghan
4 жыл бұрын
Oh no the dreaded saddle bend next
@jamiel6482
3 жыл бұрын
yes lads
@allanfuller7293
2 жыл бұрын
Please tell me what pipe thickness you use. I bought a Rothenberger Multi-Bender and when I bend pipe it cracks. I want to start practicing pipe bending. Thank you
@secondchance4498
3 жыл бұрын
chris Taylor
@creditlink
3 жыл бұрын
Hi is this really a 30degree angle because it looks more like 150degree?
@Dreancaidi
2 жыл бұрын
How do you bend 1 inch copper pipe?
@M20DAN
3 жыл бұрын
Tomkat👍🏻
@patricklynch2731
Жыл бұрын
Does anyone show how to bend 22mm pipe. What measurement do you come back to pull a 90deg
@davidjingga8356
2 жыл бұрын
Hi, does anyone know how to bend flat copper pipes? I understand I'd have to stuff the flat copper pipes with, like, fine sand so that kinks won't form when bending. But is there a specific tool to bend flat copper pipes with?
Пікірлер: 34