Love seeing the kind of work that can be done with minimal/marginal tools. Not everybody has access to a shop with the latest and greatest equipment.
@michaelperry4308
6 күн бұрын
We used the same trick making racing motorcycle frames when they were made of Reynolds Aircraft Tubing in the 60's and 70's.
@chrisbrady-t1u
Ай бұрын
I've always wanted to do that but was afraid gases would build up inside the tube and blow my head off like a pipe bomb.Thought you had to drill a couple of small vent holes to let the gases escape or you were dead.
@jarikinnunen1718
Ай бұрын
I did that using beach sand and cold bending. Using hole in plank. I put it on the stairs and I did stand on it for counter weight.
@mariop8576
17 күн бұрын
And there you have it boys a steel cane for Mr. Magoo.
@akashbrahoi6381
7 ай бұрын
Hi, That is a very good idea. Do you have the same experience bending aluminum pipes? Please teach me how much temperature is required to bend the aluminum tube?
@jarnosaarinen4583
Ай бұрын
Aluminium is very difficult to judge the temp, not sure if that be a method for that.
@xiyuanli95
Ай бұрын
nice work
@jamesbarbour8400
11 ай бұрын
Nice 'safety sandals' ! 🙄
@dancurrier374
Жыл бұрын
Good job my friend !
@dougalbyrne2817
Ай бұрын
Don't really need sand and heat to bend schedule 40 pipe just the former and and a jack, be a better job as well, only really need heat if below 10 C and then only on 2 inch and over.
@lutzvonpeter9170
6 күн бұрын
It will collapse on you if you don't fill it with sand
@dougalbyrne2817
5 күн бұрын
@@lutzvonpeter9170 schedule 40 wont its low alloy steel pipe
@fredjones1238
3 ай бұрын
that is not exhaust pipe try on 2 1/2 inch pipe
@baboowam23
Жыл бұрын
Can i bend 15degrees stainless steel pipe without using sand, but with just enough heat to bend it?
@homecreativeworks
Жыл бұрын
For me, It can't be. The pipe would be damaged if you don't use sand. Thank you! Please Like and Subscribe for more videos ♥️
@justinh1245
Жыл бұрын
What's the significance of heating the sand?
@homecreativeworks
Жыл бұрын
So that the sand will not stick to the pipe. Thank you for your support! Please Like and Subscribe for more videos ♥️ -Homecreativeworks
@alan_2056
7 ай бұрын
I've always heated the sand to bake out the moisture so that the tubing won't become pressurized and maybe pop when heated.
@kabookiejoe5534
10 ай бұрын
That’s some tiny exhaust pipe. What a joke.
@MrErasuur
9 ай бұрын
I've seen guys use this same exact method, all the way down to the charcoal, with 3" pipe, carefully bending around old rims. Not everyone can afford mandrel benders.
@davebarrie8569
9 ай бұрын
Ever hear of a motorcycle?
@wonkylommiter6364
20 күн бұрын
its just demonstrating the method. you could use bigger diameter tube, dont be such a dick
@cristianpopescu78
7 ай бұрын
...Our looks out like a damaged hot dog....why?
@MikeyMack303
24 күн бұрын
Too much work. I would just heat it and bend around a fixture.
@alan_2056
7 ай бұрын
I was hoping to see this done with thin wall exhaust tubing.
@cristianpopescu78
7 ай бұрын
Me too.
@leslieaustin151
Ай бұрын
@@cristianpopescu78Works the same, just be more careful when bending the tube. Make sure you also do not have any moisture in the sand (wet sand + enclosed space = bomb to blow up in your face.
@cristianpopescu78
Ай бұрын
@@leslieaustin151 Thanks!
@timsimpson4579
Ай бұрын
Weld a pipe closed - bad news. Work with coal in shorts and sandals - plain old stupid. No gloves - nuts. But best of all grind on the side of a wheel - only in Asia.
@nathandevine552
3 күн бұрын
Sometimes you just gotta piss with the prick ya got
@noscadefpv4954
11 ай бұрын
welding with sandals must be fun.
@Michael-lg4wz
7 ай бұрын
just need a layer of tin foil ontop during welding
@iareid8255
Ай бұрын
An excellent way to make complicated dends in thin walled tube. Arguably quicker than cutting and welding pre bent tube and visibly nicer. I don't understand why the jig was not bolted to the floor, that would give both hands to doing the bending. I cringe at the lack of guard on the angle grinder and worse the bench grinder. Abrasive wheels do shatter and with no guard thepieces would fly everywhere rather than being contained within the guard.
@rickspa8348
5 күн бұрын
Use fine dry silver sand and a wooden plug at one end with the other welded closed. Using a oxy/gas torch heat the outside of the bend more than the inside to prevent kinking. I did this job for over ten years.
@jamesboardman7048
Ай бұрын
That stone grinder looks a we bit dangerous, but your video has given me idea out a motorcycle exhaust I need to make
Пікірлер: 45