You'll probably never read this but I wish u would do more of these, man it's takes forever to find one to the point and that actually works, ty for info, I've been looking for two days and was about to break my phone lol
@Hobby365
2 жыл бұрын
Guess what? I do read these lol. My whole point in doing this channel was to get to the point. What other things are you struggling with? I Love suggestions.
@shawnmalicek1189
2 жыл бұрын
I up graded my alt to a Dx3 ,I bind it up and i have steering but no throttle and then when i put it in reverse it will go forward so you no what the problem could be? Thanks
@jerryhermann7233
Жыл бұрын
I guess the days of needing a bind plug is over.
@geek9642
17 күн бұрын
Thanks for your help believe it or not spektrum helpline couldn’t help me on that but you have
@TTORADell
11 ай бұрын
I learned nothing from this tutorial. My SCX6 comes with the Spektrum DX-3 and SR515 RX and I can find nothing related to that binding ? Anyone else have a link discussing that set up ? My SCX6 has currently become dead in the water. As the programming is currently screwed up ! The local Hobby Store here in Alaska is either stupid or clueless and says the RX is defective. But they really have no clue. I need to know a default setting or how to rebind the TX to the RX. I believe the RX is not defective and has simply lost its bind to the DX3. youtube is the most F'd up information source out there. And I have learned nothing but more confusion regarding.
@jonebalcarcel
3 ай бұрын
Do them works wit radient reaktor esc and brushless motor?
@JusRc
2 жыл бұрын
very helpful! instructions never mentioned pressing three times. Good ol youtube came through again
@Hobby365
2 жыл бұрын
So happy it helped you out
@afraz1er
Жыл бұрын
About as unhelpful as they come
@billybigbie9411
9 ай бұрын
What do u do if esc does 2 beeps in a row
@FdJ96
10 ай бұрын
Thank you thank you thank you!!
@TheMdavis07
3 жыл бұрын
Thank you for helping me out with you informative and short video. Saved the day
@Hobby365
3 жыл бұрын
You are welcome. I am happy it helped.
@rinyotsu2.0
8 ай бұрын
Thank you!!!!
@baileyn.1812
2 жыл бұрын
My sr315 doesn't flash with three presses any ideas?
@Hobby365
2 жыл бұрын
Depending on its age you may not have a dual protocol receiver. in that case you would only be binding to the DSM radios.
@KingCat_pvp
Жыл бұрын
thx u
@chelmswoodjunction
Жыл бұрын
hello i love the way you have made a test rig for testing components of the rc hobby. would you ever consider selling this item for people to make a test rig of their own. and if you would make one and sell it how much would you sell it for and would you ship to the england united kingdom??? many thanks for your time and what a brill video. peter birmingham united kingdom
@vhopkins6784
3 жыл бұрын
I have my gyro hooked up to my spectrum SR315 receiver...and gyro works until i turn on transmitter..could u help me out??
@Hobby365
3 жыл бұрын
I love that your question made me think really hard. I think your gyro must have a third connector with one wire in it. That third connector is your gyro's remote gain adjustment. If you have a 2 channel radio or if your 3 channel radio isn't set up properly, the gain is either turned all the way up or all the way down. So what is happening is when you turn on your radio the signal gets to the receiver it causes your trouble. You can test my theory by unplugging that third connector and if it solves the issue we are on the right track. If you have a three channel radio you need to go trough your radio's set up and program your third channel to a switch with a linear adjustment. This way you can set up your gyro gain to your liking from the radio. If you have a 2 channel radio just leave that gyro unplugged and use the trim pot on the gyro. I will see if I can get a video in the queue for the gyro I have in my YD-2 to help you out.
@vhopkins6784
3 жыл бұрын
Thanks for taking the time out to explain really appreciate it
@mazakq
Жыл бұрын
Hi. What to do when my transmiter don't work with second bind style, with the SLT3, only working when i push bind button one time for longer time , but when i do this is not binding on slt 3 controller...??? Help ...
@206beastman
2 жыл бұрын
I'm getting steering no throttle response
@Hobby365
2 жыл бұрын
If this is a brushless model try recalibrating the ESC. kzitem.info/news/bejne/jn6Fp4RpcYhpdWU
@pinktacotuesday4573
7 ай бұрын
Tonight after work this video will save my life on my new VRD Carbon build with DX5C/SR315 and a Hobbywing Fusion Pro. 😄
@talkischeap7418
Жыл бұрын
Will the Spektrum SR315 DSMR 3CH Receiver bind to the Rugged DX5 ?
@hanau73
Жыл бұрын
Can you have steering plug in the RX when binding?
@imemovengeance
Жыл бұрын
Hey man thanks for doing this
@adamgreear4127
Жыл бұрын
Thank you so much for this video.
@TheSteveniell
3 жыл бұрын
Hi, I’m trying same steps with same devices as you and after is done is turning left instead of right. I can’t figure this out. Help please.
@Hobby365
3 жыл бұрын
You need to flip the steering reverse switch on the radio. On the computer radios it is under the servo setup menu. On a regular radio it is a switch on the back of the radio.
@karnivor5906
Жыл бұрын
Man, you rescued my kids day! Thanks
@KRNpics
Жыл бұрын
Thanks so much for this!
@balckmetal01
3 жыл бұрын
Anyway you could tell me what transmitter are compartible ? I've searched everywhere
@Hobby365
3 жыл бұрын
There are 2 different sr315 receivers. So you need to look at the side of the receiver to see what modulation that receiver supports. Once you know the modulation you can look at the transmitter specs to see if it matches the modulation.
@rcjabroniyup4959
2 жыл бұрын
Thank you so much ! Some videos are just too long and want to babble. I just subbed. I would buy one of those 3d printed test blocks if your interested in making me one.
@Hobby365
2 жыл бұрын
I am glad I was able to help you with your R/C needs. I don't do commission work on 3d printing though I have been considering uploading some of my 3d printable designs to a source where people can print it for them self's.
@scottanderson6129
2 жыл бұрын
Does the receiver need to be sitting perfectly level and on the DX3 do the throttle and steering trims have to be set certain way during the binding/calibration? Thought I saw a Spectrum Rep video saying it did. But maybe not for the SR315.
@Hobby365
2 жыл бұрын
Those conditions are for the AVC receivers but not for the SR315.
@monosurge
2 жыл бұрын
Can you bind the slt3 transmitter to multiple SLR300 receivers and just turn on the model you want to use without rebinding every time?
@Hobby365
2 жыл бұрын
It is recommended to rebind every time as well as recalibrate and re-center the steering servos. For radios that accept multiple models you would need to look for a radio with model memory.
@rcboy6s909
3 жыл бұрын
I have a Kraton 6s and I just installed a new servo everything is good but for some reason I’m losing connection when I go far it wasn’t doing that before do you think this will help?
@Hobby365
3 жыл бұрын
Probably not, It might be an issue with the internal BEC not being able to support the power demands of your servo of choice. You can double check this by using www.hobbytown.com/tactic-4-cell-aa-battery-holder-with-futaba-j-connector-tacm2020/p-xuhwsffqqqabg4yz. Plug it into an open slot in the receiver and if it solves your issues install a auxiliary BEC like this one www.hobbytown.com/castle-creations-10-amp-adjustable-bec-cse010-0004-00/p-xqyyhehqzqsbg4yz
@Openthrottlerc
3 жыл бұрын
After i bind with slt3 the receiver goes solid but then it starts to sound a beeping noise
@Hobby365
3 жыл бұрын
You are the second person today that recalibrating the radio might solve the issue. I had one scheduled for tomorrow but have just published it try kzitem.info/news/bejne/w5eit5OKnZZjn4Y. Before you try that put some fresh batteries in the remote. I hope this helps you.
@TEAMTOYOTA85
3 жыл бұрын
Another not so helpful video.
@Hobby365
3 жыл бұрын
Im sorry I wasnt able to help you. I hope you get it figured out.
@JacobLoebel
3 жыл бұрын
When i triple tap the bind button it does nothing
@Hobby365
3 жыл бұрын
Make sure your sr315 receiver is in fact a dual protocol. There should be a sticker on the side of the receiver indicating that it is. If it turns out that it is a dual protocol receiver then make sure what ever power supply you are plugging in is fully charged. Low battery levels can cause failed binding. If all else fails then you might have a bad receiver.
@t.s.9656
2 жыл бұрын
Your instructions are crystal clear. Well done.
@Hobby365
2 жыл бұрын
Thank you so much I hope I was able to help you
@nickobrown654
3 жыл бұрын
Will this help me get throttle on my kraton 6s
@Hobby365
3 жыл бұрын
If you have steering but no throttle. Then this will not help you. You will need to search a video on calibrating your esc as a next step.
@jimmyv1753
3 жыл бұрын
So I have a Arrma Typhon 6S it came with the slt controller but says it is capable of functioning with the DX3 and the dashboard app. So I got another spectrum powered car the Losi Lasernut and it came with the DX3 and I got the BT2000 installed and it works great. I’d like to be able to use that controller for both cars (separately of course) I don’t want to risk damaging the Typhon or the receiver. Will this process work for that and will I be able to bind the controller to both vehicles at the same time so I won’t have to redo the process every time I want to use to other vehicle. I know the settings will be possibly different which is something I know I’ll have to adjust the settings for each car. But do I have to redo the bind each time? Thanks
@Hobby365
3 жыл бұрын
The receiver only has memory for one radio at a time. You will need to rebind the radio and recalibrate the esc every time you want to switch the radio.
@jimmyv1753
3 жыл бұрын
@@Hobby365 thanks that’s what I was affraid of.
@Hobby365
3 жыл бұрын
@@jimmyv1753 anytime. Sorry I didn't have better news.
@darkbloodgt6577
2 жыл бұрын
Thank you man how hard was it for someone to do this video
@Hobby365
2 жыл бұрын
I am glad it helped. I wasn't all that hard to make it just have to have a good plan.
@pascalboulet7237
3 жыл бұрын
Thank you….. You save my day))))
@Hobby365
3 жыл бұрын
You are welcome I am so happy to have helped you out.
@gregory9157
2 жыл бұрын
Great information 👍👍
@Hobby365
2 жыл бұрын
Thank you for the feed back.
@coreymartin6087
3 жыл бұрын
Would this work for transmitter DX2E seems like it wants to im binding the two and the receiver will stay solid orange but the esc just blinks fast green idk what's going on with it
@Hobby365
3 жыл бұрын
The process should be the same for the receiver but there is a bind button on that transmitter next to the on/off switch that you need to hold while turning on the transmitter.
@coreymartin6087
3 жыл бұрын
@@Hobby365 I did hold the bind button while turning on the transmitter then the receiver stayed solid green then the esc just beeped and blinked fast
@Hobby365
3 жыл бұрын
@@coreymartin6087 Ohh I see. Most ESC's have a failsafe mode that if the ESC sees a throttle input when it its powered on it goes to flashing and beeping instead of throttling out of control. I think you need to re-calibrate your esc to the radio.
@coreymartin6087
3 жыл бұрын
@@Hobby365 yeah you might be right I'll give that a go
@elimatus
3 жыл бұрын
Hey, do you know how to bind the SR315 with the dx3. Do I have to press once or three times with that radio?
@Hobby365
3 жыл бұрын
Hi there! First hold the bind button on the receiver when you power it on. Then hold the bind button under the trim knobs while you turn on the radio. That will put the radio into bind mode and they will bind.
@elimatus
3 жыл бұрын
@@Hobby365 Thanks a lot for answering. Thanks! 👍
@Hobby365
3 жыл бұрын
@@elimatus You are very welcome
@Associate00
2 жыл бұрын
@@Hobby365 you are a gentleman and a scholar, saved my ash here man! Liked and subscribed for someone that genuinely goes above and beyond!
@Hobby365
2 жыл бұрын
@@Associate00 Thank you so much for the amazing complement. I'm so glad I could help you out.
@dirtbike9003
3 жыл бұрын
Awesome!
@Hobby365
3 жыл бұрын
Thank you I am glad you enjoyed it
@georgebowen2161
2 жыл бұрын
I have a 315 that came with my brand new Axial Base Camp. I had been using my DX5C with it, and wanted to switch to the SLT3 for testing purposes, but I cannot get the SLT3 to bind. Tried the 3 pushes, but they do not work. If I press and hold, it goes into bind mode but refuses to bind to the SLT3. If I turn on my DX5C, it connects to that. Any ideas?
@Hobby365
2 жыл бұрын
Double check the side of the receiver and make sure it has a sticker that says both SLT and DSM.
@georgebowen2161
2 жыл бұрын
@@Hobby365 This transmitter came with the truck and was originally bound to the receiver. I bound it to my DX5C and now I can't get it to rebind to the SLT3.
@Hobby365
2 жыл бұрын
@@georgebowen2161 Hmmm. Not sure what to suggest if the 3 button presses don't do it. When you press the button 3 times does the receiver blink?
@georgebowen2161
2 жыл бұрын
@@Hobby365 No. Only comes on if I hold the bind button down. Weird.
@Hobby365
2 жыл бұрын
@@georgebowen2161 sounds like you may have a bad receiver.
Пікірлер: 89