Woke up this morning, radiators all cold...this vid saved me a callout :)
@FBay
Жыл бұрын
That totally worked stopped the humming sound! Thank you 🤙🏽
@johnmcgahan1001
9 ай бұрын
great clear video thanks for posting!!
@mikego18753
3 жыл бұрын
Thanks mate.
@lexdaniloff
Жыл бұрын
Thanks
@Voxac100b
2 жыл бұрын
Hi I've a wooshing then bubbling coming from one radiator we have bled the radiators but the system still has this sound. I also do not have any hot water but my radiators are very warm. Would this solve one or both problems? Pump speed is 2
@diyshop839
2 жыл бұрын
Hi there, The pump serves your heating and hot water, what I would recommend is that you bleed all your radiators, systematically starting from downstairs and working your way upstairs and finishing by bleeding your raditor that is at the highest level last. If this hasn't worked I would bleed the central heating pump as instructed in my video. If the pump speed is at 2 and has always been like that then I would leave it for now. You may need to bleed the air stalk. Hope this helps feel free the contact me for more information.
@hekhuu6620
2 жыл бұрын
hi there, do i need to change the oil or add some for my Grundfos UPS15-58FC Circulator Pump, thanks alot
@diyshop839
2 жыл бұрын
Hi there, The pump bearings are lubricated by water so they don't require any maintenance. However if you have your central heating system drained down and refilled, or your pump changed you must add a inhibitor.
@hekhuu6620
2 жыл бұрын
@@diyshop839 thank you for your reply! well i had to drain all the water and refill after i have replaced the air valve! There was a lot of air in the cast iron water radiator, and my friend!!!what s exactly an inhibitor?
@diyshop839
2 жыл бұрын
Hi there, Central heating inhibitor protects against corrosion from inside your heating system.
@Jim77463
2 жыл бұрын
Hi need help!!!!!! My mothers boiler kerosene!!!! Is cooking and not getting the water to the rads?? I tried the spinning the propeller bit!! It spins ok and plumb is scolding
@diyshop839
2 жыл бұрын
Hi there, There is a possibility that there is a air lock in the heating system, I would bleed all your radiators starting from downstairs and working your way upstairs finishing off with the radiator last that is at the highest point. Hope this helps.
@Jim77463
2 жыл бұрын
@@diyshop839 wow thanks for replying the ass has downstairs upstairs on 2 separate systems
@ivanstoicic1965
3 жыл бұрын
Reci mi prijatelju od čega zavisi i sta se postiže odredjenom brzinom pumpi imam tri pumpe jedna pre miš ventila i dve posle miš ventila na koju brzinu koja pumpa treba da radi hvala unapred.
@diyshop839
3 жыл бұрын
Thank you for your message. I have used Google translate, so I hope I have understood your question correctly. With Central Heating Pumps they normally have 3 speeds. The best way to work out what speed is the best for you, is to start on the lowest speed (speed 1) If that doesn’t work try speed 2 and then speed 3. The best way is to start at the lowest speed and work your way up.
@ivanstoicic1965
3 жыл бұрын
@@diyshop839 Sagen Sie mir, ob die erste Pumpe vor dem Mischen des Ventils eine niedrigere Drehzahl haben kann, danke recite mi moze li prva pumpa ona pre mešajući ventila da bude u manjoj brzini hvala
@SuckMyCurry
3 жыл бұрын
@@diyshop839 Good on you for translating that mate, most youtubers wouldn't have bothered!
@takisaki1503
2 жыл бұрын
Pumpe uvijek pumpaju istu količinu vode u određenom vremenu bez obzira na brzinu! Što znači, ako je vodi potrebna jedna minuta da procirkulise od pumpe i nazad kroz, recimo, 50m cijevi na najmanjoj brzini, onda će i na najvećoj brzini opet biti potrebno isto vrijeme. Čemu onda brzine? 😁 Većom brzinom pumpe se, koliko sam uspio shvatiti, postiže veći pritisak. Uprosteno rečeno, Što veći sistem, potreban je i veći pritisak. 😊 Pozdrav
@ivanstoicic1965
2 жыл бұрын
@@takisaki1503 hvala puno prijatelju
@omistic
8 ай бұрын
Can pump make difference in temperature???? Last year i installed central heating sistem and it was great, reaching temperature of 26 celsius easyyyyyyyy, going for 27 evan 28 somethimes!!!! BUT this year is not the same, going up to 26 and that’s it!!! I did bleed it little bit, evan went for that bolt inside. It is a little better but still not like last year!!!! Cleaned the stove nicely to before using it!!! What could be the problem?????
@diyshop839
7 ай бұрын
Hi There, A new pump won't make a difference in temperature, however it will make it more efficient. When changing the pump I would always recommend draining down the system and adding inhibitor to the system. If you have a magnetic filter this needs to be cleaned. I would check the pump is set at the correct speed. Also bleed all your radiators systematically starting from downstairs and working your way upstairs and finishing with the radiator at the highest point. Lastly I would check your room thermostat it could be faulty. All the best DIYShop
@CherZinc
11 ай бұрын
Thanks for video, I tried bleeding the pump twice but it's still squealing and the Noise is still coming from the pump.
@diyshop839
11 ай бұрын
Hi there, I do have another video called radiators not working/central heating pump stuck, you can try that. However if that doesn't work its a possibility that you have a build up of sludge in the system. All the best Mustafa
@CherZinc
11 ай бұрын
@@diyshop839 Thanks for taking the time to reply.
@shaftt4067
9 ай бұрын
Hy Afhter the summer the heating doesn't turn on,i have hot water but when i rurn on the heating only the top radiators from the bedrooms are getting warm,downstairs all the radiators are cold,i out my hands on the pump and i cam fell it working,shud i need to bleed the radiators? Thank you
@diyshop839
9 ай бұрын
Hi there, In this case bleeding the radiators won't work, However I do have another video called radiators not working/central heating pump stuck. What I would recommend is to follow my video and this should work, However there is a possibility that you have a gravity fed heating system, and the ballvalve/ballcock has failed in the F&E tank (the small tank) this then would need replacing. As always these jobs are a process of elimination. All the best Mustafa
@shaftt4067
9 ай бұрын
@@diyshop839 thanks for advice,I bleed the pump ,the pump is working but still the heating don t turn on..get warmed only the top rooms
@diyshop839
9 ай бұрын
Hi There, try this link to another of my videos which will help. kzitem.info/news/bejne/sGuG2KOuendlmW0si=_Vcrzq9-wqpDmY-Q All the best
@jantje2280
6 ай бұрын
And what about ticking sounds around 2 or 3 times a second? Is that the capacitor ?
@diyshop839
6 ай бұрын
Hi there, Its unlikely to be the capacitor if your pump turns off and then back on again. There is a possibility that it is a faulty wiring issue in the pump, there's also is a possibility that the impeller is struggling to turn, due to a build up of sludge in the system. I have got another video which you may find helpful, this is the link: kzitem.info/news/bejne/sGuG2KOuendlmW0si=jzHpIvZvFI9fa0I6 All the best.
@AKGarfunkel
6 ай бұрын
I have a look more hissing and water escaping than in the video. Do I just let it keep going until it stops?
@diyshop839
6 ай бұрын
Hi there, once you have the water coming out that means the air has been bleeded from the pump, and that's the job completed. If you have any further problems feel free to ask. All the best.
@rushmabaral2378
4 ай бұрын
Hey ya ! I just saw your video. We're having the same problem, and we tried to bleed the pump, but the screw just won't turn. It's way too hard to turn. Is there any solution for this ? Thank you !
@diyshop839
4 ай бұрын
Hi there, You can spray a little bit of WD40 around the bleed screw and wait 30 minutes to one hour for it to work, then you should be able to turn it anticlockwise. Hope this helps.
@lukegoodwin3292
2 жыл бұрын
I tried now the the pump is red hot with no hot water or heating what have I done ?
@diyshop839
2 жыл бұрын
Hi Luke, Ideally I need more information but I can give you some advice, if the impeller is spinning but there is no water in the pump I would check the ball valves in the loft in both tanks to make sure there working. F&E tank first then the CWS second. Also check your consumer unit, that a breaker hasn't tripped. If you have a condensate pipe that is outside it may be frozen and you would need to thaw it out by putting hot water on it (not boiling). I would check that your room thermostat is set up high. Also I would check your programmer to see what times your heating and hot water is set at. Visually check that your boiler has power to it, and always follow manufacturers instructions regarding boiler issues. Hope this helps.
@vpryt18
7 ай бұрын
Hi, what does ICHS mean in GRUNDFOS UPS 15-50 ICHS
@diyshop839
7 ай бұрын
Hi there, If you can send a photo with all the numbers and letters I can track it down for you. All the best Mustafa
@rebeccascott6403
2 жыл бұрын
What if I bled it but now it won’t stop leaking?
@diyshop839
2 жыл бұрын
Hi Rebecca, Two things make sure the rubber o ring is there which should be behind the screw, And you may have to tighten it slightly more.
@suzannealexander9681
5 ай бұрын
Mine is buzzing when the heating/water is off. Would this fix it? Thanks
@diyshop839
5 ай бұрын
Hi there, It's unusual for it to be making a noise if your heating and hot water is off. However it's worth giving it a go as a process of elimination.
@suzannealexander9681
5 ай бұрын
@@diyshop839 OK, thanks for the reply 🙂
@hikaru9624
3 жыл бұрын
Cheers for this! My boiler started making strange noises today and it came from the pump. I suspect it's an air lock but I'm not ruling out other issues such as old age. I hope it is just an air lock and nothing more complex.
@slabbyrider8665
2 жыл бұрын
what about if no water drips out? I can remove that screw & no water comes out at all. Impeller spins freely, pump runs hot & the pump makes the emersion heater buzz loudly? And the pipes bang & shake then the boiler cuts out. The same thing would happen often till i found the cowboy who installed our magnaclean filter fitted the louvres the wrong way round. Ran sweet after then today I removed a rad to decorate & it suddenly all shut down & now it no longer pumps water.
@diyshop839
2 жыл бұрын
Hi, It sounds like there is an airlock in your heating system. Firstly If your heating has been on, turn it off and let it cool down for an hour. Then bleed all your radiators, and work systematically bleeding each radiator from downstairs to upstairs. Also I would bleed the Magnaclean filter as well. Once you've done that if that doesn't work I would bleed the central heating pump. If all this fails I would check the speed setting on the central heating pump, and increase it by one. Hope that helps All the best Mustafa
@slabbyrider8665
2 жыл бұрын
@@diyshop839I done exactly that yesterday afternoon. It still wouldn't work. I then undone one nut on the pump on the feed end and no water came out of that either. So I went further and looked inside the header tank and saw the water level had dropped a couple of inches or so. I then pushed the valve down to fill it back to level. Turned the heating on and loads of bubbles came up and some gurgling. A short while later all rads were hot and it's been working flawless since 15:25pm 👍👍. Lucky as we were contemplating accepting defeat and calling a plumber.
@diyshop839
2 жыл бұрын
Well done for persevering, Fantastic news, it might be helpful to change the ball valve if it's getting stuck, Part 2 ball valve make sure it has a red seating valve as you have a gravity fed system. Low pressure system.
@Timothy_Pitt
2 жыл бұрын
what if no water drips out?
@diyshop839
2 жыл бұрын
Hi Timothy, It could be that you haven't turned the bleed screw round enough I would try that first. Other than that it could be that your impeller is stuck.
Пікірлер: 54