I hopping replacing the fluid will fix the brakes Good looking out Thanks for the video
@kerryeff407
3 жыл бұрын
Thank You very much!! I have been searching for this tool forever.
@KeffelewAssefa
3 жыл бұрын
Thank you
@yousfiamar
6 жыл бұрын
Excellent and continued
@derekmelyndadeckens2982
Жыл бұрын
This is an excellent video. Thank you for sharing
@waynebreivogel1742
3 жыл бұрын
The vacuum method is the way to do this. Bonus points for using an actual torque wrench. Kudos to that. One question, do you think I could jerry rig a shop vac with a catch bottle and some appropriate fittings to regulate vacuum pressure as the vacuum source?
@dial2fast
3 жыл бұрын
Shop vac does not provide enough PSI and doesn't have the fittings to connect.
@beloblotskiy
4 жыл бұрын
A very informative video, special thinks for the reviewing that vacuum bleeder. Good luck man.
@tiger19030
3 жыл бұрын
Very good video and well spoken!
@rtbrandley
4 жыл бұрын
hey Diald2fast, really like your videos. they are short, well done, informative. Good Job.
@dial2fast
4 жыл бұрын
Thanks for your comment!
@chiphamthien1918
2 жыл бұрын
Video very good. Thank you so much.
@drummerdem50
Жыл бұрын
great video Dial , thanks
@ahyungrocks5509
10 ай бұрын
What is the compressor size recommendation? I have a pancake compressor (very small) and did not have enough volume/power the last time I tried.
@obadiah7771
6 жыл бұрын
I would never be able to get those bleeders lose here in NY... great video though!!!
@12vgs8606
6 жыл бұрын
You certainly will not if you did what he did aka used open end wrench on it!
@xxrodneyxx
6 жыл бұрын
Pump brakes before starting (to take the assist out). Use Honda brake fluid. Great vid.
@maxfiest4096
4 жыл бұрын
I have the same mini van but is it a close or open ABS system
@laurencezemlick1979
2 жыл бұрын
I did this the cheap-ass way yesterday and it was a mess. Garage still stinks from spilled brake fluid. If you have a few cars that you own and plan on doing the brakes on all of them then it might make sense to invest in some of these gadgets now. Only advice I’d add to the video is just get the OEM Honda fluid. Small price to pay for peace of mind.
@SkunkfaceNF
3 жыл бұрын
Love your vids , but I had so many problems with the vacuum method. I didn’t get any brake fluid out. I suspect that there maybe something with vac tool in combination with user error. Had to call a friend to do the brake pump method which worked so much better. Was I supposed to pump the brake to tightness before each vacuum attempt?
@mrub7142
6 жыл бұрын
Good job as always.
@dial2fast
6 жыл бұрын
Thanks for your comment!
@OhioBikeRider
Жыл бұрын
You need to check Honda service manual for brake bleed order I'm sure you will be surprised.
@dasteufelhund
3 жыл бұрын
The penumatic...is pushing air in or drawing air out? I'm not as clear as to how the pneumatic and the pump....It's pushing compressed air in to draw fluid out...how?
@anibalmartinez5142
2 жыл бұрын
Can u use that pump to extract motor oil.
@Santos-ek8md
6 жыл бұрын
Great vid. Just what I needed to see. You make it look real ez too. Questions, once getting in to the driver seat should the firmness of the brake be seen right away? Do you discard the remaining DOT fluid? Or save it to use later? Where did you find that CFM information if it wasn’t in the ins booklet? I’ve a Porter Cable 6 gal, w/2.6 scfm @ 90psi. Is this not acceptable? Thanks,
@dial2fast
6 жыл бұрын
Unless your old brake system had air in it, usually you don't feel a huge difference after flushing the brake fluid (regardless what people tell you). The old fluid is discarded and not to be used again. This brand of bleeder gives no spec on CFM, so I used spec from another well known company which has the same design (as a general guide). I wanted to share this info because many people are not able to get this bleeder to work with their setup and CFM plays a big part in its operation.Your compressor will probably not be able to operate this tool properly.
@Santos-ek8md
6 жыл бұрын
dial2fast So I guess I’ll be looking to purchase the hand pump operated type so that pressure gets to build for vacuum, right? Thanks for the quick reply earlier. I’ve already shared your video w/ friends.
@marktechsci
2 жыл бұрын
Good video. I would bleed the brakes before changing the brakes to avoid touching the new rotors with contaminated gloves…
@jinfan775
3 жыл бұрын
my compressor only has 2.35 cfm @ 90 psi. will it work or not?
@12vgs8606
6 жыл бұрын
How much vacuum (i.e. volume) does it generate? Would handheld vacuum such as MityVac be used instead? Do you feel that you get lot more vacuum with this tool than MitVac?
@salimalhinai3034
6 жыл бұрын
Good work🔧🔧🔨👍💓
@dial2fast
6 жыл бұрын
Thanks for your comment!
@alexjiminian2847
5 жыл бұрын
Hey Dial 2 Fast where can I get a shop service manual for my 2014 Honda Odyssey Elite?
Пікірлер: 43