For me, the ideas in kzitem.infoUgkxAfqpMLyFn37qcqUl0FAzqkkycQeXqrhP Plans were a starting point for building different sheds . Ryan gives ideas that allow an individual to draw nicest conclusions into the design and building of his or her own shed.
@jfinaz99
8 жыл бұрын
Excellent explanations along with how to do it and 'those oversights' to avoid. Thanks, this is exactly the guidance I was looking for. Please continue with your outstanding tutorials for beginners like me, no doubt you saved me a lot of cursing this weekend. I've looked at several video clips on building stair railings and yours is the best! thanks, jf
@sheilamclaughlin963
5 жыл бұрын
A lot easier to nail on the floor
@steamenginewatt2712
4 жыл бұрын
Great video! You don't talk to much, you give a thorough explanation. I do my stringers and joists the same as you, 16" on center, but prior to instillation, if I see that the last stringer will be short, (less then 16" on center) I do the math and even them up. I also put a ledger board below my decking board on the steps "face" and then a ledger on my stringers, just like you, in between the outsides and notched on the center stringers, then screwed or nailed and lagged into place......Strong. I've watched countless video's where people "toe" in the stringers, or have the top step on the same plain as the deck and in my humble opinion they just don't know what they're doing, I searched for your video for affirmation of how it's done right. I'm putting in a new deck in the couple of weeks, and I appreciate your tips! Thanks!!
@davidgiesfeldt6650
2 жыл бұрын
NEXT TIME… AFTER you make the the first angle cut, temporarily attach a scrap piece of 2x to the LOWER EDGE of the post FACE at two points above and below the level cut line and away from the blade. This will avoid pinching the blade and having the waste stock fall on you. :)
@Ed-rv5wn
9 ай бұрын
thank you for the guidance Chris Pratt
@michaelwebb57
19 күн бұрын
I really like your videos. I'm a novice carpenter and preparing to build and attach stairs to my deck. My question is at 5:40 in the video you're nailing the 2x4 to the bottom of the string and holding the 2x4 flush to the outside stringer. Is there a reason the two middle stringer are outside the notch you cut and not flush with the bottom of the stringer like the outside? Can see when you place steps against deck and floor that the two middle stringers aren't flush with the floor like the outside stringers. Thanks!
@justinvilleneuve2058
5 жыл бұрын
these are always well explained videos !!
@jacquesd5781
6 жыл бұрын
Why all the whining about the detailed explanations? There are already too many half-assed videos out there that only cover part of everything that's involved. What's "common sense" to one isn't automatically for all - and besides, sometimes it's good to get a reminder on basic stuff. This covers all the bases and doesn't keep us amateur DIY's guessing. Nice work!
@Darkstalker834
3 жыл бұрын
I just used this on my deck. This is by far a much better way to install them.
@dariomendoza191
2 жыл бұрын
WELL EXPLAINED1!!! Thanks for SHARING!!!
@davidrodriguez3348
5 жыл бұрын
If you pre drill the whole then you won't have an issue with splitting the wood just my two cents worth you're doing a great job
@daveross8
4 жыл бұрын
Do t worry about the guys saying you talk too much. You’ll dial it in as you gain confidence. And as you do, you will stop saying “go ahead” which is a nervous tick in some parts of the US but sticks out for people not from those places.
@NormFarnumFamily
4 жыл бұрын
Thanks. Very comprehensive!
@tcl379
4 жыл бұрын
Wonderful!
@jens_hatje
4 жыл бұрын
When measuring for the stair railing post, why put a board down to measure off of, only to later measure from the top of the railing, then use a 2x material to bring that measurement back down the 1.5 inches? Just measure up from the stair stringer would have been a couple less steps to do. Just a thought.
@bantheshift
3 жыл бұрын
I got hung up on this too but I believe its because you need to account for the adjusted thickness of the 2x6 when its on an angle.
@jtltet
5 жыл бұрын
Why not draw that straight line across the back of your post and then line up the line on the front and back of the post and draw a line to connect and that sets your angle instead of trying to determine an angle with your speed square?
@9mmkahr
4 жыл бұрын
Same shit but I do it your way.. Regardlesss, that angle needs to be figured out anyway to bevel top of handrail where it hits deck post.
@darrenmcintosh326
3 жыл бұрын
Does pre-building work on a 26 ft long strung stair...basicly?
@enricopallazzo3244
5 жыл бұрын
I’m also a nail from behind kind of guy.
@archael18
4 жыл бұрын
Went ahead, go ahead, go ahead, went ahead, gonna go ahead, go ahead, go ahead, go ahead, make sure you go ahead, go ahead.
@Porkwhitemeat
Жыл бұрын
Hand nailing. You must work by the hour
@energizeyou6666
Жыл бұрын
What color is urine in diabetes?
@eltoncarvalho9339
2 жыл бұрын
So funny he hiding his cutting on the top of the post.
@tacaobell
4 жыл бұрын
Nice video, but you gotta work on not using the word "ummm" so much.
@georgejaymes4756
4 жыл бұрын
To much talking not enough showing how to install n cut stairway..lol
@squirrel0349
4 жыл бұрын
Way to much talking and over showing!
@popstaf
5 жыл бұрын
If you talk less, it would make sense of watching your videos.
Пікірлер: 31