The best part about this video is wendigoon in the background also the simple step by step process. Great video all around
@8BloodyKnuckles
Жыл бұрын
Glad I found this video. Trying to take mine apart to fit onto a TNV PBM-A. Was wondering why it wouldn’t unthread after a certain point.
@cpm-3374
2 жыл бұрын
To avoid small debris or fingerprints you can try to use surgical gloves.
@EagleBayNightSupplies
2 жыл бұрын
I have those when I assemble my sac lenses, but since I don't touch either the glas on the tube or lenses I don't bother with gloves. And I don't wipe them unless they a actually are dirty since they are usually already clean from factory. But thanks for the advice ☺️
@AK--yx7vj
Жыл бұрын
my dude watching straight mr ballen in the backround, thats worth a like 👍
@redplemons8084
2 жыл бұрын
Any guidance on where to get "kit" to rebuild a PVS14. mine has a milspec tube in a civilian body I forget the name of it . But its not compatible with any helmet mount.
@gkft
2 жыл бұрын
Nice video. I have a one year old PVS-14 that I got from JRH, I love it, but sometimes I wish I had a loaner to use when bringing out a friend or family member, and considered doing a more "budget" setup and trying my hand and throwing one together. I take it that you did not nitrogen purge the unit, would you say in your experience this isn't 100% necessary? Where is a good source for parts/tubes?
@perchowski3021
Жыл бұрын
You can buy wine preserver which is 100% nitrogen and spray it into the PVS14, then put the cap on. It's not as perged as a professional perge but it's a lot better than nothing. Considering it's heavier than air, it should get 95% nitrogen in approx.
@nighthorus
2 жыл бұрын
Nice man
@EagleBayNightSupplies
2 жыл бұрын
Thanks m8!
@enriquealbors5822
2 жыл бұрын
How should I clean the inside part of lens and tube ?
@EagleBayNightSupplies
2 жыл бұрын
Make sure to get rid of all debris. Then you should take a cotton Q-tip, start in the middle of the lens and move outwards in a circular motion. Do not apply to much pressure. If there are still fingerprints or grease on the tube/glas. Take a new Q-tip, dip in isopropylalcohol and redo the circulare wiping motion.
@NightVisionHunting
3 ай бұрын
What grease or sealant are you using ?
@EagleBayNightSupplies
3 ай бұрын
A high quality silicone grease that dosnt change it's viscosity due to temperature changes.
@NightVisionHunting
3 ай бұрын
@@EagleBayNightSupplies can you please tell me the brand?
@EagleBayNightSupplies
3 ай бұрын
@@NightVisionHunting Abbey Silicon gun grease
@heyarno
Жыл бұрын
Is that 8ohclock spot dirt or a tube blem?
@EagleBayNightSupplies
Жыл бұрын
It's unfortunate a blem
@heyarno
Жыл бұрын
@@EagleBayNightSupplies Oh well, the military sucks up all the good stuff these days. At least this way we get something.
@EagleBayNightSupplies
Жыл бұрын
@@heyarno It's all good, very smal and not that noticeable 😊
@rachmathidayat7736
Жыл бұрын
This is a vps madein china or original pvs 14?
@EagleBayNightSupplies
Жыл бұрын
This is a complete Carson unit with Carson glas and a Photonis tube.
@sermike16
Жыл бұрын
Parts list?
@EagleBayNightSupplies
Жыл бұрын
Carson ocular and objectiv pvs14 glas, Carson pvs14 housing, Carson pvs14 batterypack, Carson Light pipe and retainer ring and Photonis echo tube
@TomColontonio
3 ай бұрын
Why the black spot?
@EagleBayNightSupplies
3 ай бұрын
Black spots with sharp edges are defects from the manufacturing process. And black spots with soft edges are light damages. It's quite common to have a few smal black spots, especially on commercial grade tubes just like this Photonis echo tube in the video.
@davidwong209
5 ай бұрын
Don’t you have to purge the tube?
@EagleBayNightSupplies
5 ай бұрын
You can't purge a tube. But it is recommended to purge the unit once it's built. But as it says in the title "without special tools". We got full set of correct tools and purging device. But for this specific video that aims to help people who wanna build their own pvs14 so we didn't bother because cheap DIY won't afford a purging device😊 Never the less, a unit needs to be purged every 6 months which I highly doubt anyone outside the military does.
@PreppedScots
16 күн бұрын
@@EagleBayNightSupplies only way to really augment that would be the use of a inert gas like argon thats typically found in wine preservers. nowhere near a commercial purge but helps a wee bit
@TechSavvyOptics
2 жыл бұрын
That is certainly a very well “lubricated” pvs14. (Edit)
@EagleBayNightSupplies
2 жыл бұрын
You do know that you can legally obtain nightvision outside the US?
@TechSavvyOptics
2 жыл бұрын
@@EagleBayNightSupplies I may have heard about that…
@EagleBayNightSupplies
2 жыл бұрын
And regarding the lube, it's not more than was used in my ACT built unit😊
@TechSavvyOptics
2 жыл бұрын
@@EagleBayNightSupplies Yeah I believe that. From my experience, that much grease is going to migrate to places you don’t want it. That is especially true, in high heat environments. -.02
@EagleBayNightSupplies
2 жыл бұрын
@@TechSavvyOptics That's why I use high quality silicone grease that won't change its viscosity due to higher Temps. But thanks for the heads up
@davideinstein7887
Жыл бұрын
i fucked up my pigtail installing one today..... fk my life.
@EagleBayNightSupplies
Жыл бұрын
You can convert it to a autogain tube by changing the pigtail to a resistor
@jimmyjames_yt
3 ай бұрын
Dirty
@davesackenheim2937
6 ай бұрын
You know this might have been an interesting video with a little commentary but what the fuck was going on in the background what was I listening to? It made me turn it off that was annoying
Пікірлер: 42