Tutorial on plastic box building. If you have any questions, please add your questions to comments below and I will answer as best I can. Sac Makers Academy sacmakers.com
Thank you very much,this is exactly what I have been looking for to display my Pop vinyls out of box! :)
@sacmakers4770
9 жыл бұрын
Thank you COOLnessGod . I will be making more very soon!
@javipuente86
7 жыл бұрын
damn first time I see someone that knows what they're doing, I work at a custom acrylic fabrication company and I see a lot of videos giving wrong info. good work dude
@samsykes8616
Жыл бұрын
That’s good to know! Looking into making some acrylic box for metal sculptures I make.
@JemDhali
9 жыл бұрын
Really great! Hoping to see more.
@GaryMcKinnonUFO
4 жыл бұрын
Very nice, love the bending apparatus.
@b.williamchapman9774
5 жыл бұрын
I just started looking into this craft and this is the best instructional video that I have found. Thank you.
@iwantosavemoney
2 ай бұрын
Yes sir that the way a over flow box is made also
@JemmySheng
8 жыл бұрын
great work!
@florencecouture8738
Жыл бұрын
Thanks! Well done.
@marcosarebalo9099
5 жыл бұрын
i want to build custom cases for action figures on the card, i was wondering how i go about doing so? exactly what tools do i need?
@rithotyn
4 жыл бұрын
The fingers have been captured here in all their glory for posterity.
@robmill3r
3 жыл бұрын
as someone who has lost a digit to a tablesaw, this was hard to watch. I really don't understand someone not using a push stick, especially cutting down this small. eeep!
@Chevyman27705
3 жыл бұрын
Get a push stick bro. 🤘🏻
@MRNIIK
8 жыл бұрын
This was very insightful but I wish the camera work wasn't so Michael Bay
@warrenthomas1253
3 жыл бұрын
@@mcm3825 don't be a pussy say what you really mean
@DanielLouzonis
7 жыл бұрын
In other words....I can't do this on my own. :(
@supermodelatlanta1354
5 жыл бұрын
Daniel Louzonis right bc i dont have the tools.
@BioClone
4 жыл бұрын
actually only the right filament needs to be bought (so you use a batery or something and use it to heat the material, some heat gun could work aswell, however is not recomended as it works better with the same temperature on all the joint or it could get deformed) Anything else could be made with wood, or use more primitive sanding tools... also you could give the chamfers a transparent look if you did sanded it roughly with a torch, even one 4 cooking should work)
@sg3037
4 жыл бұрын
😂😆 exactly
@DeA2875
3 жыл бұрын
All you really need is a scoring tool you can get at Home Depot, the right glue and a torch tool wise. The jig is necessary though.. I make displays at work and it can be done with hand tools, a bit slower but...
@n3dnarbofficial95
2 жыл бұрын
Hahaha
@leogue8404
5 жыл бұрын
Good work, can you make 2”x4”x8 “ boxes?
@AndrewWilliams-sk1ss
4 жыл бұрын
Does anyone know what the name of that glue is by chance. The rest of the stuff i have. Cheers and great video.
@katrishamays6058
7 жыл бұрын
need more details on the saw blade who makes it and where can you get it
@n3dnarbofficial95
2 жыл бұрын
Standard home tool setup that everyone should have...... lol
@gerrybalderas2062
5 жыл бұрын
What we call that equipment that you use to bent the plastic
@akashdarji8117
4 жыл бұрын
What type of silicone can i use for a acrylic fish tank that i want to build please tell me what i can use
@kristeearbourgh5296
Жыл бұрын
What happens if you get glue residue on plexiglass where you don’t want it? Will something remove it?
@teabagNBG
6 жыл бұрын
are there online shops where i can order custom shapes?
@leoderadt596
7 жыл бұрын
Curious about the details of the trim-flush fence for the router. It says details in the description, but not seeing them. Am I missing something obvious?
@sacmakers4770
3 жыл бұрын
Hey! I was using a 3/4" Trim Flush Router bit with a standard barring. Hope that helps! Nothing fancy. Just needs to ride along wall and trim off the panel that has been glued to the bended panel.
@sacmakers4770
3 жыл бұрын
I will dive back into the Fence fabrication at some point. Life got crazy.
@seamoreseeless
8 жыл бұрын
I hope you are looking forward to a trip to the ER. The method of cutting with your (R) hand between the material, straight edge and blade is extremely dangerous. You should be using a block of wood to hold work straight without putting yourself in danger. I sincerely hope this tragedy never happens.
@brannonharris9761
8 жыл бұрын
+Norman Featherston Your first and last sentences nearly contradict eachother. If you turn on annotations, the video mentions the dangers and suggests guards.
@seamoreseeless
8 жыл бұрын
You are correct Brannon Harris. I should have used the word 'may' instead of 'hope'. All the best, stay safe.
@brannonharris9761
8 жыл бұрын
+Norman Featherston hey, thank you!
@Tigerbricks11
6 жыл бұрын
He’s cutting clear material. It’s not like it’s going to surprise him a cut off his fingertip.
@webtrekkeruk2487
6 жыл бұрын
Sullyvan Famous last words!
@anancrypto2213
2 жыл бұрын
1 how to bind/join transparent polycarbonate sheet to make a box? Will acrylic grade glue/polyfix can be used ? 2 How much thick sheet will be sufficient to withstand hot water upto 45 d celcius ?
@melannieworld
8 жыл бұрын
Question, would you make a custom box? please let me know.
@MADDMOODY516
Жыл бұрын
Is there any way to cut it without a saw? Like with scissors?
@fredygabuardy546
3 жыл бұрын
Hey ! Did you use a normal router bit to clean up the extra plexiglass or did you use a special bit for it?
@sacmakers4770
3 жыл бұрын
Hey! I was using a 3/4" Trim Flush Router bit with a standard barring. Hope that helps! Nothing fancy. Just needs to ride along wall and trim off the panel that has been glued to the bended panel.
@anancrypto2213
2 жыл бұрын
@@sacmakers4770 1 how to bind/join transparent polycarbonate sheet to make a box? Will acrylic grade glue/polyfix/chlorofom can be used ? 2 How much thick sheet will be sufficient to withstand hot water upto 45 d celcius ?
@bryynn_lxmn
2 жыл бұрын
what called that plastic clear you used???
@dgiroir6344
4 жыл бұрын
Great video, Hey do you still have 10 fingers. Be safe my friend!
@polymakegames
4 жыл бұрын
Yea, still building and got all ten. Of course, that's thanks to swapping to push sticks in general.
@michaeltudda2988
3 жыл бұрын
I am looking for a three side wall for a diorama? 3 foot sides by 14 inches high, by four feet long, by 14 inches high, any suggestions?
@mothersmucker1
4 жыл бұрын
and for those of us at home who do not have all this equipment and tools.....
@hernanalvarez7519
3 жыл бұрын
what glue you use?
@calebcombs3669
4 жыл бұрын
Is this acrylic or polycarbonate?
@karishmashah6270
5 жыл бұрын
Would you be willing to take an order? I can send you a pic of what I have (which broke) and measurements. Thanks!
@anabelorozco3973
4 жыл бұрын
Do u sell them i really need one 6"x6"x11" I looked everywhere i can't find I'm bedridden cancer i want it to put my trophy Cancer fighting trophy
@guyfisher2050
5 жыл бұрын
How do you calibrate the router fence for removing saw cuts (1:27), I don't find the link for this or in any of your videos
@highendvape
Жыл бұрын
Same
@elsahernandez6409
Жыл бұрын
Do you make custom acrylic displays? I need about 10
@juans.3547
3 жыл бұрын
Dude I would honestly pay u for this I’m not even joking if u could make me some 1:64 display cases that would be amazing 😇
@Dhampir6990
6 жыл бұрын
How do you place the action figure in the case if its glued shut
@sacmakers4770
3 жыл бұрын
It isn't glued shut. Just placed onto its step-base. Like a friction fit bottom
@jacobgregory2426
Жыл бұрын
Hey do you make customs ones to sell?
@mightySHRIMP420
3 жыл бұрын
I'll make my own cases for pops and pokemon boxs. Nvm I'll just buy them 😂
@COOLnessGod
9 жыл бұрын
Nice video.
@emcapitan7494
2 жыл бұрын
what was called the blade you used to bend the case?
@highendvape
Жыл бұрын
It’s just called a heat bender
@kevinh8736
6 жыл бұрын
I need one that is 16 inches tall, 8 inches wide and 2 feet long with a black base.
@sacmakers4770
6 жыл бұрын
Feel free to ask any questions!
@kevinh8736
6 жыл бұрын
SacMakers - Do you have a website I can order from????
@Phoenixknight79
4 жыл бұрын
how much would you charge
@sindoooyasser
6 жыл бұрын
Hello please which blade do you use?
@sammybaby1413
5 жыл бұрын
Any carbide tipped blade should work fine. 60 - 80 tooth. Triple chip grind works best.
@mikejessmax
Жыл бұрын
Holy smokes, you're pretty brave (or uneducated) with that table saw. Still have all your fingers?
@the_beyswapper9688
2 жыл бұрын
I want them for Beyblades
@kabba4575
4 жыл бұрын
Uhhhh...ur website........my phone will not let me access it because it says that the domain is trying to hack into my account or retrieve passwords.
@FF60MpD
3 жыл бұрын
How much to build me a custom one?
@bingcocris4286
5 жыл бұрын
hi SacMakers can i ask L x W x H of that project. thanks
@liamr6672
4 жыл бұрын
Wow, you trimmed your fingernail while cutting at 50 seconds.
@collectordannyrr3654
3 жыл бұрын
Could you make Four please for my Ninja Turtles? Then another 6 For my Street Sharks Pleaseeee
@nisaleranda32
5 жыл бұрын
can i buy 200pcs from this?
@candychen7408
5 жыл бұрын
Our company specializes in producing acrylic products. Can you email me your request? candyacrylic@163.com
@lupitaayala3690
4 жыл бұрын
Well, in order to make a cheap plastic box, I need to expend more money buying the tools .... I can do my own without tools thanks
@mydemon
4 жыл бұрын
Can you post your it KZitem tutorial for this?
@LLPOF
3 жыл бұрын
To anybody watching this, please don't use the saw in the manner used in this video.
@sacmakers4770
3 жыл бұрын
I agree. But almost 7 years later I still have 10 fingers. Freedom to create in the manner in which we choose is truly a blessing. I don't remember making a tutorial on using a table saw. :)
@theintrovertedguy7054
11 ай бұрын
Oh no
@rustyneedles3743
2 жыл бұрын
Well, someones sure to lose a finger someday.
@youtubefree7389
3 жыл бұрын
Now do this without using those type of tools
@chrissangenette6359
Жыл бұрын
$100 worth of tools plus materials spend the $20 on Amazon
@iwantosavemoney
2 ай бұрын
30 seconds worth of typing for not
@vinnyivanov2906
5 жыл бұрын
I cant like what I seen because camera moves around so much that video was like an action movie
@mydemon
4 жыл бұрын
Dude you lost me 16 seconds into the video when you're using a professional sawblade as large as a fridge for this. How is this diy?
@tomm1968
4 жыл бұрын
It's a table saw with a carbide tipped saw blade. You can buy them at Home Depot. Not Professional Grade Unobtainium. They're pretty ordinary if you actually go out and look.
@mydemon
4 жыл бұрын
@@tomm1968 Yeah I ended up getting one, it fits nicely in the middle of my tiny NYC studio apartment. However, I use it as sa surface to score the acrylic sheets with a knife and cut it that way. Otherwise it wakes up the baby.
Пікірлер: 100